All:
I hope I am doing this right, the instructions for submitting kernel bug
reports are a bit confusing. I have been redirected here, because I reported
Bug #1328746 on Launchpad, and the bug was identified as an upstream issue.
With this e-mail, I am following the instructions here:
https://wiki.ubuntu.com/Bugs/Upstream/kernel
[1.] Soundblaster Audigy front panel MIDI fails to initialize
[2.] The bug concerns the Soundblaster Audigy cards (emu10k1 chip) with front
panel extension, such as the Audigy ZS Pro. Those cards have two MIDI UARTs,
the on-board joystick MIDI interface and the optional front-panel module.
Under Linux, the front-panel MIDI input does not work. People with dual-boot
systems have reported that booting Windows first, then rebooting into Linux
makes the UART function properly.
The cause for the bug lies in the fact that the front panel MIDI is routed
through a microcontroller (resides in the front panel module), and this
microcontroller needs a defined reset signal once after power-up. Up to this
point, the GPIO _levels_ are initialized correctly, but the reset _pulse_ is
never issued. Essentially, the emu10k1 chip's GPIO2 needs to be pulled high
for a brief interval when the kernle module snd-emu10k1 initializes.
The bug can be reproduced with almost any kernel (I tested this from 2.6.x to
3.15.0) when the computer is cold-started and booted directly into Linux. I
also propose a workaround, which is a modified emumpu401.c file that fixes the
issue.
[3.] (this section empty as per Launchpad instructions)
[4.] $ cat /proc/version
Linux version 3.15.0-031500-lowlatency (apw@gomeisa) (gcc version 4.6.3
(Ubuntu/Linaro 4.6.3-1ubuntu5) ) #201406081435 SMP PREEMPT Sun Jun 8 18:44:17
UTC 2014
[5.] No kernel oops exists
[6.] The problem begins at boot-time, and no script can be used to trigger it.
[7.] $ lsb_release -rd
Description: Ubuntu 12.04.4 LTS
Release: 12.04
[7.1.] $ sh ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux cantabile 3.15.0-031500-lowlatency #201406081435 SMP PREEMPT Sun Jun 8
18:44:17 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux
Gnu C 4.6
Gnu make 3.81
binutils 2.22
util-linux 2.20.1
mount support
module-init-tools 3.16
e2fsprogs 1.42
pcmciautils 018
PPP 2.4.5
Linux C Library 2.15
Dynamic linker (ldd) 2.15
Procps 3.2.8
Net-tools 1.60
Kbd 1.15.2
Sh-utils 8.13
wireless-tools 30
Modules Loaded bnep rfcomm bluetooth rpcsec_gss_krb5 6lowpan_iphc nfsd
nfsv4 nfs_acl auth_rpcgss nfs fscache lockd sunrpc snd_emu10k1_synth
snd_emux_synth snd_seq_virmidi snd_seq_midi_emul snd_emu10k1 snd_ac97_codec
ac97_bus snd_pcm snd_util_mem snd_hwdep snd_seq_midi snd_rawmidi
snd_seq_midi_event snd_seq hid_generic hid_logitech_dj ppdev snd_timer
snd_seq_device uas usb_storage parport_pc usbhid snd hid psmouse emu10k1_gp
serio_raw gameport soundcore edac_core sp5100_tco mac_hid k10temp wmi f71882fg
edac_mce_amd i2c_piix4 lp parport pata_acpi firewire_ohci firewire_core r8169
mii crc_itu_t ahci pata_atiixp libahci pata_jmicron
[7.2.] $ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 16
model : 4
model name : AMD Processor model unknown
stepping : 2
cpu MHz : 800.000
cache size : 512 KB
physical id : 0
siblings : 4
core id : 0
cpu cores : 4
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb
rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid
pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a
misalignsse 3dnowprefetch osvw ibs skinit wdt hw_pstate npt lbrv svm_lock
nrip_save
bogomips : 5599.89
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 48 bits physical, 48 bits virtual
power management: ts ttp tm stc 100mhzsteps hwpstate
processor : 1
vendor_id : AuthenticAMD
cpu family : 16
model : 4
model name : AMD Processor model unknown
stepping : 2
cpu MHz : 800.000
cache size : 512 KB
physical id : 0
siblings : 4
core id : 1
cpu cores : 4
apicid : 1
initial apicid : 1
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb
rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid
pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a
misalignsse 3dnowprefetch osvw ibs skinit wdt hw_pstate npt lbrv svm_lock
nrip_save
bogomips : 5599.89
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 48 bits physical, 48 bits virtual
power management: ts ttp tm stc 100mhzsteps hwpstate
processor : 2
vendor_id : AuthenticAMD
cpu family : 16
model : 4
model name : AMD Processor model unknown
stepping : 2
cpu MHz : 1600.000
cache size : 512 KB
physical id : 0
siblings : 4
core id : 2
cpu cores : 4
apicid : 2
initial apicid : 2
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb
rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid
pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a
misalignsse 3dnowprefetch osvw ibs skinit wdt hw_pstate npt lbrv svm_lock
nrip_save
bogomips : 5599.89
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 48 bits physical, 48 bits virtual
power management: ts ttp tm stc 100mhzsteps hwpstate
processor : 3
vendor_id : AuthenticAMD
cpu family : 16
model : 4
model name : AMD Processor model unknown
stepping : 2
cpu MHz : 800.000
cache size : 512 KB
physical id : 0
siblings : 4
core id : 3
cpu cores : 4
apicid : 3
initial apicid : 3
fpu : yes
fpu_exception : yes
cpuid level : 5
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb
rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid
pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a
misalignsse 3dnowprefetch osvw ibs skinit wdt hw_pstate npt lbrv svm_lock
nrip_save
bogomips : 5599.89
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 48 bits physical, 48 bits virtual
power management: ts ttp tm stc 100mhzsteps hwpstate
[7.3.] $ cat /proc/modules
bnep 19884 2 - Live 0x0000000000000000
rfcomm 75078 0 - Live 0x0000000000000000
bluetooth 465597 10 bnep,rfcomm, Live 0x0000000000000000
rpcsec_gss_krb5 40513 0 - Live 0x0000000000000000
6lowpan_iphc 18968 1 bluetooth, Live 0x0000000000000000
nfsd 291805 2 - Live 0x0000000000000000
nfsv4 486947 1 - Live 0x0000000000000000
nfs_acl 12883 1 nfsd, Live 0x0000000000000000
auth_rpcgss 60073 2 rpcsec_gss_krb5,nfsd, Live 0x0000000000000000
nfs 252218 2 nfsv4, Live 0x0000000000000000
fscache 64282 2 nfsv4,nfs, Live 0x0000000000000000
lockd 95124 2 nfsd,nfs, Live 0x0000000000000000
sunrpc 305164 17 rpcsec_gss_krb5,nfsd,nfsv4,nfs_acl,auth_rpcgss,nfs,lockd,
Live 0x0000000000000000
snd_emu10k1_synth 17414 0 - Live 0x0000000000000000
snd_emux_synth 42830 1 snd_emu10k1_synth, Live 0x0000000000000000
snd_seq_virmidi 13525 1 snd_emux_synth, Live 0x0000000000000000
snd_seq_midi_emul 17975 1 snd_emux_synth, Live 0x0000000000000000
snd_emu10k1 162497 1 snd_emu10k1_synth, Live 0x0000000000000000
snd_ac97_codec 135207 1 snd_emu10k1, Live 0x0000000000000000
ac97_bus 12730 1 snd_ac97_codec, Live 0x0000000000000000
snd_pcm 109717 2 snd_emu10k1,snd_ac97_codec, Live 0x0000000000000000
snd_util_mem 14117 2 snd_emux_synth,snd_emu10k1, Live 0x0000000000000000
snd_hwdep 13613 2 snd_emux_synth,snd_emu10k1, Live 0x0000000000000000
snd_seq_midi 13564 0 - Live 0x0000000000000000
snd_rawmidi 30816 3 snd_seq_virmidi,snd_emu10k1,snd_seq_midi, Live
0x0000000000000000
snd_seq_midi_event 14899 2 snd_seq_virmidi,snd_seq_midi, Live
0x0000000000000000
snd_seq 67636 5
snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_midi,snd_seq_midi_event,
Live 0x0000000000000000
hid_generic 12559 0 - Live 0x0000000000000000
hid_logitech_dj 18647 0 - Live 0x0000000000000000
ppdev 17711 0 - Live 0x0000000000000000
snd_timer 30069 3 snd_emu10k1,snd_pcm,snd_seq, Live 0x0000000000000000
snd_seq_device 14497 5
snd_emu10k1_synth,snd_emu10k1,snd_seq_midi,snd_rawmidi,snd_seq, Live
0x0000000000000000
uas 27672 0 - Live 0x0000000000000000
usb_storage 66862 1 uas, Live 0x0000000000000000
parport_pc 32906 0 - Live 0x0000000000000000
usbhid 53072 0 - Live 0x0000000000000000
snd 74146 10
snd_emux_synth,snd_seq_virmidi,snd_emu10k1,snd_ac97_codec,snd_pcm,snd_hwdep,snd_rawmidi,snd_seq,snd_timer,snd_seq_device,
Live 0x0000000000000000
hid 106436 3 hid_generic,hid_logitech_dj,usbhid, Live 0x0000000000000000
psmouse 113046 0 - Live 0x0000000000000000
emu10k1_gp 12622 0 - Live 0x0000000000000000
serio_raw 13434 0 - Live 0x0000000000000000
gameport 19986 2 emu10k1_gp, Live 0x0000000000000000
soundcore 12680 1 snd, Live 0x0000000000000000
edac_core 63001 0 - Live 0x0000000000000000
sp5100_tco 14134 0 - Live 0x0000000000000000
mac_hid 13275 0 - Live 0x0000000000000000
k10temp 13191 0 - Live 0x0000000000000000
wmi 19379 0 - Live 0x0000000000000000
f71882fg 36181 0 - Live 0x0000000000000000
edac_mce_amd 22792 0 - Live 0x0000000000000000
i2c_piix4 22310 0 - Live 0x0000000000000000
lp 17799 0 - Live 0x0000000000000000
parport 42432 3 ppdev,parport_pc,lp, Live 0x0000000000000000
pata_acpi 13053 0 - Live 0x0000000000000000
firewire_ohci 45251 0 - Live 0x0000000000000000
firewire_core 65209 1 firewire_ohci, Live 0x0000000000000000
r8169 73316 0 - Live 0x0000000000000000
mii 13981 1 r8169, Live 0x0000000000000000
crc_itu_t 12707 1 firewire_core, Live 0x0000000000000000
ahci 30167 0 - Live 0x0000000000000000
pata_atiixp 13279 4 - Live 0x0000000000000000
libahci 32191 1 ahci, Live 0x0000000000000000
pata_jmicron 12775 0 - Live 0x0000000000000000
[7.4.a.] $ cat /proc/ioports
0000-0cf7 : PCI Bus 0000:00
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0071 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:14.1
0170-0177 : pata_atiixp
01f0-01f7 : 0000:00:14.1
01f0-01f7 : pata_atiixp
02f8-02ff : serial
0376-0376 : 0000:00:14.1
0376-0376 : pata_atiixp
03c0-03df : vga+
03f6-03f6 : 0000:00:14.1
03f6-03f6 : pata_atiixp
03f8-03ff : serial
040b-040b : pnp 00:05
04d0-04d1 : pnp 00:05
04d6-04d6 : pnp 00:05
0800-0803 : ACPI PM1a_EVT_BLK
0804-0805 : ACPI PM1a_CNT_BLK
0808-080b : ACPI PM_TMR
0810-0815 : ACPI CPU throttle
0820-0827 : ACPI GPE0_BLK
0900-090f : pnp 00:05
0910-091f : pnp 00:05
0b00-0b0f : pnp 00:05
0b20-0b3f : pnp 00:05
0c00-0c01 : pnp 00:05
0c14-0c14 : pnp 00:05
0c50-0c51 : pnp 00:05
0c52-0c52 : pnp 00:05
0c6c-0c6c : pnp 00:05
0c6f-0c6f : pnp 00:05
0cd0-0cd1 : pnp 00:05
0cd2-0cd3 : pnp 00:05
0cd4-0cd5 : pnp 00:05
0cd6-0cd7 : pnp 00:05
0cd8-0cdf : pnp 00:05
0cf8-0cff : PCI conf1
0d00-ffff : PCI Bus 0000:00
0e80-0f5f : pnp 00:0b
0e80-0e87 : f71882fg
0f40-0f4f : pnp 00:0b
4000-400f : 0000:00:11.0
4000-400f : ahci
5000-5003 : 0000:00:11.0
5000-5003 : ahci
6000-6007 : 0000:00:11.0
6000-6007 : ahci
7000-7003 : 0000:00:11.0
7000-7003 : ahci
8000-8007 : 0000:00:11.0
8000-8007 : ahci
9000-9fff : PCI Bus 0000:01
9800-987f : 0000:01:00.0
a000-bfff : PCI Bus 0000:02
a400-a40f : 0000:02:00.1
a400-a40f : pata_jmicron
a800-a803 : 0000:02:00.1
a800-a803 : pata_jmicron
b000-b007 : 0000:02:00.1
b000-b007 : pata_jmicron
b400-b403 : 0000:02:00.1
b400-b403 : pata_jmicron
b800-b807 : 0000:02:00.1
b800-b807 : pata_jmicron
c000-cfff : PCI Bus 0000:03
c800-c8ff : 0000:03:00.0
c800-c8ff : r8169
d000-dfff : PCI Bus 0000:04
d800-d8ff : 0000:04:00.0
d800-d8ff : r8169
e000-efff : PCI Bus 0000:05
e000-e07f : 0000:05:02.0
e400-e407 : 0000:05:00.1
e400-e407 : emu10k1-gp
e800-e83f : 0000:05:00.0
e800-e83f : EMU10K1
fe00-fefe : pnp 00:05
ff00-ff0f : 0000:00:14.1
ff00-ff0f : pata_atiixp
[7.4.b.] $ cat /proc/iomem
00000000-00000fff : reserved
00001000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : PCI Bus 0000:00
000c0000-000cddff : Video ROM
000d0000-000dffff : PCI Bus 0000:00
000e6000-000fffff : reserved
000f0000-000fffff : System ROM
00100000-cffaffff : System RAM
01000000-017831d8 : Kernel code
017831d9-01d1e43f : Kernel data
01e77000-01fdbfff : Kernel bss
2d000000-34ffffff : Crash kernel
cffb0000-cffbdfff : ACPI Tables
cffbe000-cffdffff : ACPI Non-volatile Storage
cffe0000-cfffffff : reserved
d0000000-dfffffff : PCI Bus 0000:00
d0000000-dfffffff : PCI Bus 0000:01
d0000000-dfffffff : 0000:01:00.0
e0000000-efffffff : PCI MMCONFIG 0000 [bus 00-ff]
e0000000-efffffff : pnp 00:0c
f0000000-febfffff : PCI Bus 0000:00
fbffa000-fbffafff : 0000:00:14.5
fbffa000-fbffafff : ohci_hcd
fbffb000-fbffbfff : 0000:00:13.1
fbffb000-fbffbfff : ohci_hcd
fbffc000-fbffcfff : 0000:00:13.0
fbffc000-fbffcfff : ohci_hcd
fbffd000-fbffdfff : 0000:00:12.1
fbffd000-fbffdfff : ohci_hcd
fbffe000-fbffefff : 0000:00:12.0
fbffe000-fbffefff : ohci_hcd
fbfff400-fbfff4ff : 0000:00:13.2
fbfff400-fbfff4ff : ehci_hcd
fbfff800-fbfff8ff : 0000:00:12.2
fbfff800-fbfff8ff : ehci_hcd
fbfffc00-fbffffff : 0000:00:11.0
fbfffc00-fbffffff : ahci
fc000000-fe7fffff : PCI Bus 0000:01
fc000000-fcffffff : 0000:01:00.0
fd000000-fdffffff : 0000:01:00.0
fe7e0000-fe7fffff : 0000:01:00.0
fe800000-fe8fffff : PCI Bus 0000:02
fe8fe000-fe8fffff : 0000:02:00.0
fe8fe000-fe8fffff : ahci
fe900000-fe9fffff : PCI Bus 0000:03
fe9c0000-fe9dffff : 0000:03:00.0
fe9ff000-fe9fffff : 0000:03:00.0
fe9ff000-fe9fffff : r8169
fea00000-feafffff : PCI Bus 0000:04
feac0000-feadffff : 0000:04:00.0
feaff000-feafffff : 0000:04:00.0
feaff000-feafffff : r8169
feb00000-febfffff : PCI Bus 0000:05
febf8000-febfbfff : 0000:05:00.2
febff000-febff7ff : 0000:05:02.0
febff000-febff7ff : firewire_ohci
febff800-febfffff : 0000:05:00.2
febff800-febfffff : firewire_ohci
fec00000-fec003ff : IOAPIC 0
fec10000-fec1001f : pnp 00:05
fed00000-fed003ff : HPET 2
fee00000-fee00fff : Local APIC
fee00000-fee00fff : pnp 00:04
ffb80000-ffbfffff : pnp 00:05
fff00000-ffffffff : reserved
100000000-22fffffff : System RAM
[7.5.] $ sudo lspci -vvv
[sudo] password for {user}:
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD790 Host Bridge
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RD790 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
Capabilities: [c4] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn+ LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency 0: [a]
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz-
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA-
UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz-
600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [40] HyperTransport: Retry Mode
Capabilities: [54] HyperTransport: UnitID Clumping
Capabilities: [9c] HyperTransport: #1a
00:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RX780/RD790 PCI to
PCI bridge (external gfx0 port A) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fc000000-fe7fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency
L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4181
Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI]
Device 5956
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010 <?>
Capabilities: [110 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
00:05.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RX780/RD790 PCI to
PCI bridge (PCI express gpp port B) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: fe800000-fe8fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4191
Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI]
Device 5956
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010 <?>
Capabilities: [110 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
00:06.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD790 PCI to PCI
bridge (PCI express gpp port C) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41a1
Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI]
Device 5956
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010 <?>
Capabilities: [110 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
00:07.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RX780/RD790 PCI to
PCI bridge (PCI express gpp port D) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41b1
Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI]
Device 5956
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010 <?>
Capabilities: [110 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD/ATI]
SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] (prog-if 01 [AHCI 1.0])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 8000 [size=8]
Region 1: I/O ports at 7000 [size=4]
Region 2: I/O ports at 6000 [size=8]
Region 3: I/O ports at 5000 [size=4]
Region 4: I/O ports at 4000 [size=16]
Region 5: Memory at fbfffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] SATA HBA v1.0 InCfgSpace
Kernel driver in use: ahci
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI]
SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:12.1 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1
Controller (prog-if 10 [OHCI])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI]
SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fbfff800 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci-pci
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI]
SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fbffc000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:13.1 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1
Controller (prog-if 10 [OHCI])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fbffb000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI]
SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fbfff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci-pci
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller
(rev 3a)
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort+ <MAbort- >SERR- <PERR- INTx-
Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
00:14.1 IDE interface: Advanced Micro Devices, Inc. [AMD/ATI]
SB7x0/SB8x0/SB9x0 IDE Controller (prog-if 8a [Master SecP PriP])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ff00 [size=16]
Capabilities: [70] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: 00000000 Data: 0000
Kernel driver in use: pata_atiixp
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0
LPC host controller
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI
Bridge (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD/ATI]
SB7x0/SB8x0/SB9x0 USB OHCI2 Controller (prog-if 10 [OHCI])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbffa000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor
HyperTransport Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave-
<EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn+ LSEn- ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: [a]
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz-
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+
UIDRD- ExtRS- UCnfE-
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor
DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor
Link Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
01:00.0 VGA compatible controller: NVIDIA Corporation G73 [GeForce 7600 GS]
(rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device 822a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fc000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at 9800 [size=128]
Expansion ROM at fe7e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns,
L1 <4us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1,
Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [128 v1] Power Budgeting <?>
02:00.0 SATA controller: JMicron Technology Corp. JMB363 SATA/IDE Controller
(rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 5: Memory at fe8fe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express (v1) Legacy Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0
<1us, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: ahci
02:00.1 IDE interface: JMicron Technology Corp. JMB363 SATA/IDE Controller
(rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at a800 [size=4]
Region 4: I/O ports at a400 [size=16]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_jmicron
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411
PCI Express Gigabit Ethernet Controller (rev 01)
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: I/O ports at c800 [size=256]
Region 2: Memory at fe9ff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fe9c0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Vital Product Data
Unknown small resource type 05, will not decode more.
Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+
Address: 00000000fee0100c Data: 41c1
Capabilities: [60] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <1us,
L1 unlimited
ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [84] Vendor Specific Information: Len=4c <?>
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap-
ChkEn-
Capabilities: [12c v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [148 v1] Device Serial Number b8-02-00-00-10-ec-81-68
Capabilities: [154 v1] Power Budgeting <?>
Kernel driver in use: r8169
04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411
PCI Express Gigabit Ethernet Controller (rev 01)
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: I/O ports at d800 [size=256]
Region 2: Memory at feaff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Vital Product Data
Unknown small resource type 05, will not decode more.
Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+
Address: 00000000fee0f00c Data: 41d1
Capabilities: [60] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <1us,
L1 unlimited
ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [84] Vendor Specific Information: Len=4c <?>
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap-
ChkEn-
Capabilities: [12c v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [148 v1] Device Serial Number b9-02-00-00-10-ec-81-68
Capabilities: [154 v1] Power Budgeting <?>
Kernel driver in use: r8169
05:00.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04)
Subsystem: Creative Labs Device 2006
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at e800 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_emu10k1
05:00.1 Input device controller: Creative Labs SB Audigy Game Port (rev 04)
Subsystem: Creative Labs SB Audigy Game Port
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: I/O ports at e400 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Emu10k1_gameport
05:00.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04)
(prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: firewire_ohci
05:02.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)]
IEEE 1394 OHCI Controller (rev c0) (prog-if 10 [OHCI])
Subsystem: Foxconn International, Inc. Device 0e0e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at e000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: firewire_ohci
[7.6.] $ cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: MKNSSDCR120GB Rev: 502A
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: SONY Model: DVD RW DW-D22A Rev: BYS2
Type: CD-ROM ANSI SCSI revision: 05
Host: scsi10 Channel: 00 Id: 00 Lun: 00
Vendor: Generic- Model: Compact Flash Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Host: scsi10 Channel: 00 Id: 00 Lun: 01
Vendor: Generic- Model: SM/xD-Picture Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Host: scsi10 Channel: 00 Id: 00 Lun: 02
Vendor: Generic- Model: SD/MMC Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Host: scsi10 Channel: 00 Id: 00 Lun: 03
Vendor: Generic- Model: MS/MS-Pro Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
[7.7.] Not applicable
[X.]Other notes, patches, fixes, workarounds:
a) Launchpad bug report:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1328746
b) Workaround: Fixed file emumpu401.c pasted below. Note: The code below can be
used to compile the module snd-emu10k1, and the bug does not occur with the
module when compiled with the code below.
/*
* Copyright (c) by Jaroslav Kysela <perex@xxxxxxxx>
* Routines for control of EMU10K1 MPU-401 in UART mode
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <linux/time.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <sound/core.h>
#include <sound/emu10k1.h>
#define EMU10K1_MIDI_MODE_INPUT (1<<0)
#define EMU10K1_MIDI_MODE_OUTPUT (1<<1)
static inline unsigned char mpu401_read(struct snd_emu10k1 *emu,
struct snd_emu10k1_midi *mpu, int idx)
{
if (emu->audigy)
return (unsigned char)snd_emu10k1_ptr_read(emu, mpu->port + idx, 0);
else
return inb(emu->port + mpu->port + idx);
}
static inline void mpu401_write(struct snd_emu10k1 *emu,
struct snd_emu10k1_midi *mpu, int data, int idx)
{
if (emu->audigy)
snd_emu10k1_ptr_write(emu, mpu->port + idx, 0, data);
else
outb(data, emu->port + mpu->port + idx);
}
#define mpu401_write_data(emu, mpu, data) mpu401_write(emu, mpu, data, 0)
#define mpu401_write_cmd(emu, mpu, data) mpu401_write(emu, mpu, data, 1)
#define mpu401_read_data(emu, mpu) mpu401_read(emu, mpu, 0)
#define mpu401_read_stat(emu, mpu) mpu401_read(emu, mpu, 1)
#define mpu401_input_avail(emu,mpu) (!(mpu401_read_stat(emu,mpu) & 0x80))
#define mpu401_output_ready(emu,mpu) (!(mpu401_read_stat(emu,mpu) & 0x40))
#define MPU401_RESET 0xff
#define MPU401_ENTER_UART 0x3f
#define MPU401_ACK 0xfe
static void mpu401_clear_rx(struct snd_emu10k1 *emu, struct snd_emu10k1_midi
*mpu)
{
int timeout = 100000;
for (; timeout > 0 && mpu401_input_avail(emu, mpu); timeout--)
mpu401_read_data(emu, mpu);
#ifdef CONFIG_SND_DEBUG
if (timeout <= 0)
dev_err(emu->card->dev,
"cmd: clear rx timeout (status = 0x%x)\n",
mpu401_read_stat(emu, mpu));
#endif
}
/*
*/
static void do_emu10k1_midi_interrupt(struct snd_emu10k1 *emu, struct
snd_emu10k1_midi *midi, unsigned int status)
{
unsigned char byte;
if (midi->rmidi == NULL) {
snd_emu10k1_intr_disable(emu, midi->tx_enable | midi->rx_enable);
return;
}
spin_lock(&midi->input_lock);
if ((status & midi->ipr_rx) && mpu401_input_avail(emu, midi)) {
if (!(midi->midi_mode & EMU10K1_MIDI_MODE_INPUT)) {
mpu401_clear_rx(emu, midi);
} else {
byte = mpu401_read_data(emu, midi);
if (midi->substream_input)
snd_rawmidi_receive(midi->substream_input, &byte, 1);
}
}
spin_unlock(&midi->input_lock);
spin_lock(&midi->output_lock);
if ((status & midi->ipr_tx) && mpu401_output_ready(emu, midi)) {
if (midi->substream_output &&
snd_rawmidi_transmit(midi->substream_output, &byte, 1) == 1) {
mpu401_write_data(emu, midi, byte);
} else {
snd_emu10k1_intr_disable(emu, midi->tx_enable);
}
}
spin_unlock(&midi->output_lock);
}
static void snd_emu10k1_midi_interrupt(struct snd_emu10k1 *emu, unsigned int
status)
{
do_emu10k1_midi_interrupt(emu, &emu->midi, status);
}
static void snd_emu10k1_midi_interrupt2(struct snd_emu10k1 *emu, unsigned int
status)
{
do_emu10k1_midi_interrupt(emu, &emu->midi2, status);
}
static int snd_emu10k1_midi_cmd(struct snd_emu10k1 * emu, struct
snd_emu10k1_midi *midi, unsigned char cmd, int ack)
{
unsigned long flags;
int timeout, ok;
spin_lock_irqsave(&midi->input_lock, flags);
mpu401_write_data(emu, midi, 0x00);
/* mpu401_clear_rx(emu, midi); */
mpu401_write_cmd(emu, midi, cmd);
if (ack) {
ok = 0;
timeout = 10000;
while (!ok && timeout-- > 0) {
if (mpu401_input_avail(emu, midi)) {
if (mpu401_read_data(emu, midi) == MPU401_ACK)
ok = 1;
}
}
if (!ok && mpu401_read_data(emu, midi) == MPU401_ACK)
ok = 1;
} else {
ok = 1;
}
spin_unlock_irqrestore(&midi->input_lock, flags);
if (!ok) {
dev_err(emu->card->dev,
"midi_cmd: 0x%x failed at 0x%lx (status = 0x%x, data = 0x%x)!!!\n",
cmd, emu->port,
mpu401_read_stat(emu, midi),
mpu401_read_data(emu, midi));
return 1;
}
return 0;
}
static int snd_emu10k1_midi_input_open(struct snd_rawmidi_substream
*substream)
{
struct snd_emu10k1 *emu;
struct snd_emu10k1_midi *midi = (struct snd_emu10k1_midi *)substream-
>rmidi->private_data;
unsigned long flags;
emu = midi->emu;
if (snd_BUG_ON(!emu))
return -ENXIO;
spin_lock_irqsave(&midi->open_lock, flags);
midi->midi_mode |= EMU10K1_MIDI_MODE_INPUT;
midi->substream_input = substream;
if (!(midi->midi_mode & EMU10K1_MIDI_MODE_OUTPUT)) {
spin_unlock_irqrestore(&midi->open_lock, flags);
if (snd_emu10k1_midi_cmd(emu, midi, MPU401_RESET, 1))
goto error_out;
if (snd_emu10k1_midi_cmd(emu, midi, MPU401_ENTER_UART, 1))
goto error_out;
} else {
spin_unlock_irqrestore(&midi->open_lock, flags);
}
return 0;
error_out:
return -EIO;
}
static int snd_emu10k1_midi_output_open(struct snd_rawmidi_substream
*substream)
{
struct snd_emu10k1 *emu;
struct snd_emu10k1_midi *midi = (struct snd_emu10k1_midi *)substream-
>rmidi->private_data;
unsigned long flags;
emu = midi->emu;
if (snd_BUG_ON(!emu))
return -ENXIO;
spin_lock_irqsave(&midi->open_lock, flags);
midi->midi_mode |= EMU10K1_MIDI_MODE_OUTPUT;
midi->substream_output = substream;
if (!(midi->midi_mode & EMU10K1_MIDI_MODE_INPUT)) {
spin_unlock_irqrestore(&midi->open_lock, flags);
if (snd_emu10k1_midi_cmd(emu, midi, MPU401_RESET, 1))
goto error_out;
if (snd_emu10k1_midi_cmd(emu, midi, MPU401_ENTER_UART, 1))
goto error_out;
} else {
spin_unlock_irqrestore(&midi->open_lock, flags);
}
return 0;
error_out:
return -EIO;
}
static int snd_emu10k1_midi_input_close(struct snd_rawmidi_substream
*substream)
{
struct snd_emu10k1 *emu;
struct snd_emu10k1_midi *midi = (struct snd_emu10k1_midi *)substream-
>rmidi->private_data;
unsigned long flags;
int err = 0;
emu = midi->emu;
if (snd_BUG_ON(!emu))
return -ENXIO;
spin_lock_irqsave(&midi->open_lock, flags);
snd_emu10k1_intr_disable(emu, midi->rx_enable);
midi->midi_mode &= ~EMU10K1_MIDI_MODE_INPUT;
midi->substream_input = NULL;
if (!(midi->midi_mode & EMU10K1_MIDI_MODE_OUTPUT)) {
spin_unlock_irqrestore(&midi->open_lock, flags);
err = snd_emu10k1_midi_cmd(emu, midi, MPU401_RESET, 0);
} else {
spin_unlock_irqrestore(&midi->open_lock, flags);
}
return err;
}
static int snd_emu10k1_midi_output_close(struct snd_rawmidi_substream
*substream)
{
struct snd_emu10k1 *emu;
struct snd_emu10k1_midi *midi = (struct snd_emu10k1_midi *)substream-
>rmidi->private_data;
unsigned long flags;
int err = 0;
emu = midi->emu;
if (snd_BUG_ON(!emu))
return -ENXIO;
spin_lock_irqsave(&midi->open_lock, flags);
snd_emu10k1_intr_disable(emu, midi->tx_enable);
midi->midi_mode &= ~EMU10K1_MIDI_MODE_OUTPUT;
midi->substream_output = NULL;
if (!(midi->midi_mode & EMU10K1_MIDI_MODE_INPUT)) {
spin_unlock_irqrestore(&midi->open_lock, flags);
err = snd_emu10k1_midi_cmd(emu, midi, MPU401_RESET, 0);
} else {
spin_unlock_irqrestore(&midi->open_lock, flags);
}
return err;
}
static void snd_emu10k1_midi_input_trigger(struct snd_rawmidi_substream
*substream, int up)
{
struct snd_emu10k1 *emu;
struct snd_emu10k1_midi *midi = (struct snd_emu10k1_midi *)substream-
>rmidi->private_data;
emu = midi->emu;
if (snd_BUG_ON(!emu))
return;
if (up)
snd_emu10k1_intr_enable(emu, midi->rx_enable);
else
snd_emu10k1_intr_disable(emu, midi->rx_enable);
}
static void snd_emu10k1_midi_output_trigger(struct snd_rawmidi_substream
*substream, int up)
{
struct snd_emu10k1 *emu;
struct snd_emu10k1_midi *midi = (struct snd_emu10k1_midi *)substream-
>rmidi->private_data;
unsigned long flags;
emu = midi->emu;
if (snd_BUG_ON(!emu))
return;
if (up) {
int max = 4;
unsigned char byte;
/* try to send some amount of bytes here before interrupts */
spin_lock_irqsave(&midi->output_lock, flags);
while (max > 0) {
if (mpu401_output_ready(emu, midi)) {
if (!(midi->midi_mode & EMU10K1_MIDI_MODE_OUTPUT) ||
snd_rawmidi_transmit(substream, &byte, 1) != 1) {
/* no more data */
spin_unlock_irqrestore(&midi->output_lock, flags);
return;
}
mpu401_write_data(emu, midi, byte);
max--;
} else {
break;
}
}
spin_unlock_irqrestore(&midi->output_lock, flags);
snd_emu10k1_intr_enable(emu, midi->tx_enable);
} else {
snd_emu10k1_intr_disable(emu, midi->tx_enable);
}
}
/*
*/
static struct snd_rawmidi_ops snd_emu10k1_midi_output =
{
.open = snd_emu10k1_midi_output_open,
.close = snd_emu10k1_midi_output_close,
.trigger = snd_emu10k1_midi_output_trigger,
};
static struct snd_rawmidi_ops snd_emu10k1_midi_input =
{
.open = snd_emu10k1_midi_input_open,
.close = snd_emu10k1_midi_input_close,
.trigger = snd_emu10k1_midi_input_trigger,
};
static void snd_emu10k1_midi_free(struct snd_rawmidi *rmidi)
{
struct snd_emu10k1_midi *midi = rmidi->private_data;
midi->interrupt = NULL;
midi->rmidi = NULL;
}
static int emu10k1_midi_init(struct snd_emu10k1 *emu, struct snd_emu10k1_midi
*midi, int device, char *name)
{
struct snd_rawmidi *rmidi;
int err;
if ((err = snd_rawmidi_new(emu->card, name, device, 1, 1, &rmidi)) < 0)
return err;
midi->emu = emu;
spin_lock_init(&midi->open_lock);
spin_lock_init(&midi->input_lock);
spin_lock_init(&midi->output_lock);
strcpy(rmidi->name, name);
snd_rawmidi_set_ops(rmidi, SNDRV_RAWMIDI_STREAM_OUTPUT,
&snd_emu10k1_midi_output);
snd_rawmidi_set_ops(rmidi, SNDRV_RAWMIDI_STREAM_INPUT,
&snd_emu10k1_midi_input);
rmidi->info_flags |= SNDRV_RAWMIDI_INFO_OUTPUT |
SNDRV_RAWMIDI_INFO_INPUT |
SNDRV_RAWMIDI_INFO_DUPLEX;
rmidi->private_data = midi;
rmidi->private_free = snd_emu10k1_midi_free;
midi->rmidi = rmidi;
return 0;
}
int snd_emu10k1_midi(struct snd_emu10k1 *emu)
{
struct snd_emu10k1_midi *midi = &emu->midi;
int err;
if ((err = emu10k1_midi_init(emu, midi, 0, "EMU10K1 MPU-401 (UART)")) < 0)
return err;
midi->tx_enable = INTE_MIDITXENABLE;
midi->rx_enable = INTE_MIDIRXENABLE;
midi->port = MUDATA;
midi->ipr_tx = IPR_MIDITRANSBUFEMPTY;
midi->ipr_rx = IPR_MIDIRECVBUFEMPTY;
midi->interrupt = snd_emu10k1_midi_interrupt;
return 0;
}
int snd_emu10k1_audigy_midi(struct snd_emu10k1 *emu)
{
struct snd_emu10k1_midi *midi;
int err;
unsigned int val; /* Needed in GPOUT2 pulse initialization */
midi = &emu->midi;
if ((err = emu10k1_midi_init(emu, midi, 0, "Audigy MPU-401 (UART)")) < 0)
return err;
midi->tx_enable = INTE_MIDITXENABLE;
midi->rx_enable = INTE_MIDIRXENABLE;
midi->port = A_MUDATA1;
midi->ipr_tx = IPR_MIDITRANSBUFEMPTY;
midi->ipr_rx = IPR_MIDIRECVBUFEMPTY;
midi->interrupt = snd_emu10k1_midi_interrupt;
midi = &emu->midi2;
if ((err = emu10k1_midi_init(emu, midi, 1, "Audigy MPU-401 #2")) < 0)
return err;
midi->tx_enable = INTE_A_MIDITXENABLE2;
midi->rx_enable = INTE_A_MIDIRXENABLE2;
midi->port = A_MUDATA2;
midi->ipr_tx = IPR_A_MIDITRANSBUFEMPTY2;
midi->ipr_rx = IPR_A_MIDIRECVBUFEMPTY2;
midi->interrupt = snd_emu10k1_midi_interrupt2;
snd_printk(KERN_ERR "Both Audigy MPU-401 UARTs now intialized\n");
val = inl(emu->port + A_IOCFG);
outl (val | A_IOCFG_GPOUT2, emu->port + A_IOCFG);
udelay(10); /* udelay is a bad kludge, but remember that this is called
only once on startup */
outl (val, emu->port + A_IOCFG);
snd_printk(KERN_ERR "Audigy MPU-401: Haidekker's Hack - UART enabled\n");
return 0;
}
--
To unsubscribe from this list: send the line "unsubscribe linux-sound" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
[Index of Archives]
[Pulseaudio]
[Linux Audio Users]
[ALSA Devel]
[Fedora Desktop]
[Fedora SELinux]
[Big List of Linux Books]
[Yosemite News]
[KDE Users]
