I've revised the configuration and followed all your instructions.
I'll try to give you a better explain of my problem.
a) I need a bridged (3) configuration, because I have to connect the guests from each others. (via ssh and execute mpi). I've three hosts, each of one has at least a guest.
I'll only explain about the configuration of one of them, because the problem is only related a one configuration.
hostname=rionegro ip=192.168.1.4
guest-name=rnompi1
b) I've configured host bridge following step by step ther instruction on http://wiki.libvirt.org/page/Networking
this is the /etc/network/config
# The loopback network interface
auto lo
iface lo inet loopback
auto br0
iface br0 inet static
address 192.168.1.4
netmask 255.255.255.0
network 192.168.1.0
broadcast 192.168.1.255
gateway 192.168.1.10
bridge_ports eth0
bridge_stp on
bridge_fd 0
bridge_maxwait 0
c) this is the xml guest configuration related to the network.
<interface type='bridge'>
<source bridge='br0'/>
</interface>
d) But the guest doesn't get any IP automatically, and create an interface with a variable name (eth4, eth5,etch6..). I don't know how to achieve the guest don't behave like this and create always its network interface with a fixed name, for example, eth0).
Why I ask that?
if the guest created an interface with a fixed name, I would configure and static ip for the it.
I'm attaching a printscreen "rnompi1.jpg" that show what ifconfig ahow on the guest (eth14 and without any IP). It doesn't get their host either.
The only way I achieve to solve but "temporally" until reboot is configuring the guest statically using the name of the interface that has just up.In that case every works fine, and the guest can connect to all the other guests on the lan and others can connect to it.
But this only works until reboot or reconfigure the guest, because each time the name of interface change, and my configuration I had done of /etc/network/interface didn't work any more because is related to another interface.
I hope I've explained better the problem I have.
Thank you very much, you've already helped too much to better understand the different cases of network configuration
Regards.
2011/2/10 Marcela Castro León <mcastrol@xxxxxxxxx>
Hello Laine:
Thank you very much.
I've showed only one of the guest, each one have it's own ip address. Anyway, I'll follow your advise of revise all the configuration after reading the doc.
Thank you very much again.
Regards.2011/2/8 Laine Stump <laine@xxxxxxxxx>(For future questions such as this, you may find you get a better response (and lower signal-noise ratio) by asking on the recently -created libvirt-users@xxxxxxxxxx list, as libvir-list has a very large volume of patches and discussion about the internals of libvirt)So are you saying that you're attempting to give each guest the *same* IP address? There's no way that can possibly work, even if each is connected to a separate virtual network or bridge. Since the host's IP stack can "see" all of the guests' network traffic, regardless of the connection mode you choose, each must have a unique IP address even if they can't see each other.
On 02/08/2011 12:05 PM, Marcela Castro León wrote:Hello
I've a lan of virtual machine configured with bridge. I've a private lan of 4 machine, but one of them have 2 lan-card with access to internet.
Evertything works almost fine, except that I've configured on each guest the static configuration of the bridge with the ip address, like this:
auto lo
iface lo inet loopback
auto eth6
iface eth6 inet static
address 192.168.1.41
network 192.168.1.0
netmask 255.255.255.0
gateway 192.168.1.10
There must be a mixup in the explanation - I'm understanding that you put the same config file in each guest, but each guest, when it starts, shows a different ethernet interface in its ifconfig. That doesn't seem right, because none of the guests know about each other. Or are you saying something different? Where are you seeing the "eth6", "eth7", ... "eth12"? In the guest XML config maybe?
But each time I, for example, define the guest, it start with a ascending number of interface: eth6,eth7, eth8, etc, Now is initializing with eth12.Why are you doing a manual/static definition on the guest at all? It's simpler to just leave the guest to automatically configure its eth0, and if you really want a particular IP address for a particular guest, handle that with a <host> element in the <dhcp> section of the virtual network the guest is connected to (or, if you're using a pure bridging setup, then in the static hosts config of the dhcp server on that network).
So, it doesn't get the manual configuration I've done on the /etc/network/interfaces.
How can avoid this way of work of the number of ethernet interface the guest start?
The guest xml interface configuration cannot be used to setup the IP address, route, etc config of the guest. It is only used for two things:
A way i'm trying to solve is configuring the interface trough the guest xml definition,
1) configuring what kind of hardware appears on the guest (but not what name the guest gives to it!)
2) configuring how that hardware is connected to the physical network (usually either via an existing bridge interface on the host (in order for the guest to appear as if its directly connected to the physical network), or via a "virtual network" created by libvirt (which is really just a bridge that's not directly connected to any physical interface, relying instead on the host's IP stack to route packets from the guest out to the physical network.)That document is targeted towards software developers writing applications to manage virtual guests using the libvirt API, not for system administrators who are configuring virtual guests manually (or, more likely, by using software that uses the libvirt API, eg virsh or virt-manager). It likely contains more detail and less overview than what you need, which is probably what led to the confusion. I've included a pointer to a wiki page below that is more the appropriate level of information (Justin, if the docs you were working on are somewhere easily accessible, you can point to those instead.)
but the operation "define" on virsh accepted without error the xml i've done, but the dumpxml doesn't show them, so, it doesn't work at all.
I've followed the instruction that said the manual "Application development guide - a guide to application development with libvirt" on page 71.
You are confusing the guest interface config (that is part of the guest's XML config, and described above), and host physical interface config (that is not in any way associated with guest config, but instead used to configure the host's physical network interfaces, bridges, bonds, and vlan interfaces; and nearly as important, is not supported on Ubuntu anyway).
The whole definition of the VM is attached, but the related to interface is:
<interface type='bridge'>
<source bridge='br0'/>
<target dev='vnet0'/>
<protocol>
<ip address="192.168.1.41" prefix="24"/>
<route gateway="192.168.1.10"/>
</protocol>
<bridge stp="off" delay="0.01">
<interface type="ethernet" name="eth12">
<protocol>
<ip address="192.168.1.41" prefix="24"/>
<route gateway="192.168.1.10"/>
</protocol>
</interface>
</bridge>
</interface>
Actual guest interface config is *much* simpler than that.That's because everything else you've put in your guest config is not actually a part of a valid guest interface config, and so is ignored.
But after define, the dumpxml only show this part:
<interface type='bridge'>
<mac address='52:54:00:3c:92:9a'/>
<source bridge='br0'/>
</interface>
In this case I think it may be useful to start over. You've somehow been tricked into misunderstanding the way that network configuration in libvirt works, confusing host interface config with guest interface config, and the resulting config bears little resemblance to what would actually work.
I would appreciate any help to solve the question. The problem I've is I lost the access to the guest every time the libvirt change the name of the interface eth1,2,3, etc.
==
The first step is to read this page:
http://wiki.libvirt.org/page/Networking
to get a basic overview.
==
Second step: you should decide which of the three methods of connecting to guests to the physical network you want to use:
1) NATed
2) routed
3) bridged
The simplest is (1), and that will probably work just fine as long as 1) you don't need incoming connections to the guests, and 2) you're not concerned about getting the last fraction of an ounce of performance out of the network.
Depending on which of those 3 you decide to use:
==
Third step: follow the instructions to either create a bridge interface on the host connected to a physical network interface (for (3)), or to create a libvirt virtual network using one of the two modes ((1) or (2) - actually the stock libvirt config already has a "default" network that is probably adequate for (1), and unless you understand IP routing very well, you'll likely want to avoid (2)).
Once the physical network is setup:
==
Fourth step: define your guests. In each guest, you'll have an <interface> element, but it will be much simpler than what you've previously tried. For bridged mode, the interface section would look like this:</interface>
<interface type='bridge'>
<source bridge='br0'/>
Depending on the guest, you may want to specify what type of hardware is presented to the guest (default is rtl, which almost always works, but is not the best perfrorming), in particular, if the guest supports virtio-net, you'll want to add this into the <interface> element:
<model type='virtio'/>
For NATed or routed mode, the guest's interface definition would look like this:
<interface type='network'> <source network='default'/> </interface>(replace "default" with the name of the network you've defined, if you've defined your own). In this case also, you can add a <model type='...'/> if appropriate.
Note that I don't put anything in the <interface> element about MAC address, target device, or bus address. Those are all setup automatically by libvirt the first time you start the guest, and it will make sure that the guests don't interfere with each other.
==
Fifth step: only if you need a particular guest to have a particular fixed IP address, either 1) edit the network config file on the guest, 2) add a static host to the libvirt virtual network definition (giving the MAC address provided to the guest by libvirt during the initial guest startup) with a <host> element added to the <dhcp> element of the network; details are here:
http://www.libvirt.org/formatnetwork.html
or 3) if you're using the bridged method to connect to the physical network, again either configure the guest's own config file, or add a static host definition to the dhcp server running on your physical network.
If you still have problems don't hesitate to send another mail (although, as I said at the top, sending to libvirt-users@xxxxxxxxxx may yield better results than libvir-list@xxxxxxxxxx).
Attachment:
rnompi1.jpg
Description: JPEG image
