Hi Stefan, May be you can try again this test of macvtap on your environment, but please remove the bridge from eth0. because macvtap doesent work with bridge setup. -----Original Message----- From: Amit Tewari Sent: Thursday, December 15, 2011 9:05 AM To: 'Laine Stump'; libvir-list@xxxxxxxxxx Subject: RE: macvtap nt working on kvm Hi, Actually macvatap doesn't work with bridge. So once the physical device is attached to a bridge, a macvtap attached to that device no longer works. In my case there is no bridge on the interface. but still guest os is not able to get ip address. Is there no support for macvtap on red hat 6.1 x_86 platforms? -----Original Message----- From: libvir-list-bounces@xxxxxxxxxx [mailto:libvir-list-bounces@xxxxxxxxxx] On Behalf Of Laine Stump Sent: Thursday, December 15, 2011 2:31 AM To: libvir-list@xxxxxxxxxx Subject: Re: macvtap nt working on kvm On 12/14/2011 02:26 PM, Stefan Berger wrote: > On 12/14/2011 07:40 AM, Amit Tewari wrote: >> >> Hi all, >> >> My test environment >> >> Host os=rhel6.1 >> >> Guest os = rhel6.1 >> >> Libvirt=0.8.7 >> >> Kvm hypervisor >> >> I have made this entry in guest xml file >> >> <interface type='direct'> >> >> <source dev='eth0' mode='bridge'/> >> >> <model type='virtio'/> >> >> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' >> function='0x0'/> >> >> </interface> >> >> Now when I start the guest >> >> *#virsh start guest* >> >> Following macvtap0 is created on host and is shown below >> >> #*ip link show macvtap0* >> >> 51: macvtap0@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc >> mq state UNKNOWN qlen 500 >> >> link/ether 52:54:00:55:AE:B5brd ff:ff:ff:ff:ff:ff >> >> but when the guest is up and I try to perform >> >> ** >> >> *# ifup eth0* >> >> *eth0 has same mac address as that of macvatap0 that is >> 52:54:00:55:AE:B5* >> >> ** >> >> *due to this guest is not able to get dhcp address nor static ip >> address is working*. >> >> Please let me know how macvtap work on kvm. >> > > I have tried your setup on my machine with the following host > configuration: > > # brctl show > bridge name bridge id STP enabled interfaces > br0 8000.001a64d00016 no eth0 > virbr0 8000.000000000000 yes > > If I use the configuration as you have shown it doesn't work for me, > either. However, if I use > > <source dev='br0' mode='bridge'/> > > then it works as expected. Do you happen to have a similar > configuration on the host with the interface the macvtap device wants > to use as 'source' being bridged? Interesting. So you're saying that once the physical device is attached to a bridge, a macvtap attached to that device no longer works? That's useful to know :-) -- libvir-list mailing list libvir-list@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/libvir-list DISCLAIMER: ----------------------------------------------------------------------------------------------------------------------- The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only. It shall not attach any liability on the originator or NECHCL or its affiliates. Any views or opinions presented in this email are solely those of the author and may not necessarily reflect the opinions of NECHCL or its affiliates. Any form of reproduction, dissemination, copying, disclosure, modification, distribution and / or publication of this message without the prior written consent of the author of this e-mail is strictly prohibited. If you have received this email in error please delete it and notify the sender immediately. . ----------------------------------------------------------------------------------------------------------------------- -- libvir-list mailing list libvir-list@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/libvir-list