If you take a checkpoint snapshot of a running domain, then pause
qemu, then restore the snapshot, the result should be a running
domain, but the code was leaving things paused. Furthermore, if
you take a checkpoint of a paused domain, then run, then restore,
there was a brief but non-deterministic window of time where the
domain was running rather than paused. Fix both of these
discrepancies by always pausing before restoring.
Also, check that the VM is active every time lock is dropped
between two monitor calls.
* src/qemu/qemu_driver.c (qemuDomainRevertToSnapshot): Always
pause before reversion.
---
src/qemu/qemu_driver.c | 61 +++++++++++++++++++++++++++++++++--------------
1 files changed, 43 insertions(+), 18 deletions(-)
diff --git a/src/qemu/qemu_driver.c b/src/qemu/qemu_driver.c
index 12f8179..7950aff 100644
--- a/src/qemu/qemu_driver.c
+++ b/src/qemu/qemu_driver.c
@@ -8776,44 +8776,69 @@ static int qemuDomainRevertToSnapshot(virDomainSnapshotPtr snapshot,
if (snap->def->state == VIR_DOMAIN_RUNNING
|| snap->def->state == VIR_DOMAIN_PAUSED) {
-
+ /* When using the loadvm monitor command, qemu does not know
+ * whether to pause or run the reverted domain, and just stays
+ * in the same state as before the monitor command, whether
+ * that is paused or running. We always pause before loadvm,
+ * to have finer control. */
if (virDomainObjIsActive(vm)) {
priv = vm->privateData;
+ if (virDomainObjGetState(vm, NULL) == VIR_DOMAIN_RUNNING) {
+ if (qemuProcessStopCPUs(driver, vm,
+ VIR_DOMAIN_PAUSED_FROM_SNAPSHOT,
+ QEMU_ASYNC_JOB_NONE) < 0)
+ goto endjob;
+ /* Create an event now in case the restore fails, so
+ * that user will be alerted that they are now paused.
+ * If restore later succeeds to a running state, we
+ * replace this event with another. */
+ event = virDomainEventNewFromObj(vm,
+ VIR_DOMAIN_EVENT_SUSPENDED,
+ VIR_DOMAIN_EVENT_STARTED_FROM_SNAPSHOT);
+ if (!virDomainObjIsActive(vm)) {
+ qemuReportError(VIR_ERR_INTERNAL_ERROR, "%s",
+ _("guest unexpectedly quit"));
+ goto endjob;
+ }
+ }
qemuDomainObjEnterMonitorWithDriver(driver, vm);
rc = qemuMonitorLoadSnapshot(priv->mon, snap->def->name);
qemuDomainObjExitMonitorWithDriver(driver, vm);
- if (rc < 0)
+ if (rc < 0) {
+ /* XXX resume domain if it was running before the
+ * failed loadvm attempt? */
goto endjob;
+ }
} else {
if (qemuDomainSnapshotSetCurrentActive(vm, driver->snapshotDir) < 0)
goto endjob;
rc = qemuProcessStart(snapshot->domain->conn, driver, vm, NULL,
- false, false, -1, NULL, VIR_VM_OP_CREATE);
+ true, false, -1, NULL, VIR_VM_OP_CREATE);
virDomainAuditStart(vm, "from-snapshot", rc >= 0);
+ if (rc < 0)
+ goto endjob;
if (qemuDomainSnapshotSetCurrentInactive(vm,
driver->snapshotDir) < 0)
goto endjob;
- if (rc < 0)
- goto endjob;
}
+ /* Touch up domain state. */
if (snap->def->state == VIR_DOMAIN_PAUSED) {
- /* qemu unconditionally starts the domain running again after
- * loadvm, so let's pause it to keep consistency
- * XXX we should have used qemuProcessStart's start_paused instead
- */
- rc = qemuProcessStopCPUs(driver, vm,
- VIR_DOMAIN_PAUSED_FROM_SNAPSHOT,
- QEMU_ASYNC_JOB_NONE);
+ virDomainObjSetState(vm, VIR_DOMAIN_PAUSED,
+ VIR_DOMAIN_PAUSED_FROM_SNAPSHOT);
+ } else {
+ if (!virDomainObjIsActive(vm)) {
+ qemuReportError(VIR_ERR_INTERNAL_ERROR, "%s",
+ _("guest unexpectedly quit"));
+ goto endjob;
+ }
+ rc = qemuProcessStartCPUs(driver, vm, snapshot->domain->conn,
+ VIR_DOMAIN_RUNNING_FROM_SNAPSHOT,
+ QEMU_ASYNC_JOB_NONE);
if (rc < 0)
goto endjob;
- event = virDomainEventNewFromObj(vm,
- VIR_DOMAIN_EVENT_SUSPENDED,
- VIR_DOMAIN_EVENT_SUSPENDED_FROM_SNAPSHOT);
- } else {
- virDomainObjSetState(vm, VIR_DOMAIN_RUNNING,
- VIR_DOMAIN_RUNNING_FROM_SNAPSHOT);
+ virDomainEventFree(event);
event = virDomainEventNewFromObj(vm,
VIR_DOMAIN_EVENT_STARTED,
VIR_DOMAIN_EVENT_STARTED_FROM_SNAPSHOT);
--
1.7.4.4
--
libvir-list mailing list
libvir-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/libvir-list