On Wed, May 11, 2022 at 11:41:52AM -0400, Eric Garver wrote: > Convert the existing behavior into policies. > > This commit has no functional changes. > > Signed-off-by: Eric Garver <eric@xxxxxxxxxxx> > --- > src/network/libvirt-nat-out.policy | 12 ++++++++++++ > src/network/libvirt-to-host.policy | 20 ++++++++++++++++++++ > src/network/libvirt.zone | 23 +++++------------------ > src/network/meson.build | 10 ++++++++++ > 4 files changed, 47 insertions(+), 18 deletions(-) > create mode 100644 src/network/libvirt-nat-out.policy > create mode 100644 src/network/libvirt-to-host.policy > > diff --git a/src/network/libvirt-nat-out.policy b/src/network/libvirt-nat-out.policy > new file mode 100644 > index 000000000000..7d1cf6dfb4c4 > --- /dev/null > +++ b/src/network/libvirt-nat-out.policy > @@ -0,0 +1,12 @@ > +<?xml version="1.0" encoding="utf-8"?> > +<policy target="ACCEPT"> > + <short>libvirt-nat-out</short> > + > + <description> > + This policy is used to allow NAT virtual machine traffic to the > + rest of the network. > + </description> > + > + <ingress-zone name="libvirt" /> > + <egress-zone name="ANY" /> > +</policy> The 'libvirt' zone contains the host bridge device (virbr0, IP address 192.168.122.1). The VMs are implicitly in 'libvirt' zone because their TAP devices are members of virbr0. So this policy allows traffic originating in the VMs to forwarded to any other zone. IIUC, it would also allow traffic originating from the host via the virbr0 device to forward to any other zone. In practice the only traffic originating on the host from virbr0, should be traffic destined for the guest. Is it possible to force traffic on host destined for the LAN to originate in virbr0, and forward with NAT, instead of just originating in eth0 and get onto the LAN without forwarding ? If it is possible, do we actually care ? > diff --git a/src/network/libvirt-to-host.policy b/src/network/libvirt-to-host.policy > new file mode 100644 > index 000000000000..045b35d58d0d > --- /dev/null > +++ b/src/network/libvirt-to-host.policy > @@ -0,0 +1,20 @@ > +<?xml version="1.0" encoding="utf-8"?> > +<policy target="REJECT"> > + <short>libvirt-to-host</short> > + > + <description> > + This policy is used to filter traffic from virtual machines to the > + host. > + </description> > + > + <ingress-zone name="libvirt" /> > + <egress-zone name="HOST" /> > + > + <protocol value='icmp'/> > + <protocol value='ipv6-icmp'/> > + <service name='dhcp'/> > + <service name='dhcpv6'/> > + <service name='dns'/> > + <service name='ssh'/> > + <service name='tftp'/> > +</policy> So this applies to traffic originating in the VM, and destined for the host. I'm fuzzy on exactly what "HOST" expands to in our context. IIUC 'policy' rules apply to traffic transitting between zones, but we shouldn't have any zone transits involved. virbr0 is in the 'libvirt' zones and VM TAP devs are part of virbr0. So traffic VM -> host should be entirely within the libvirt zone, never transitting zones. Does this use of "HOST", for example allow traffic from the VMs to connect to the host via its public IP address on eth0, instead of via its private IP on virbr0 which is what we want ? > diff --git a/src/network/libvirt.zone b/src/network/libvirt.zone > index b1e84b52ecc9..4c5639d8a84f 100644 > --- a/src/network/libvirt.zone > +++ b/src/network/libvirt.zone > @@ -1,25 +1,12 @@ > <?xml version="1.0" encoding="utf-8"?> > -<zone target="ACCEPT"> > +<zone> > <short>libvirt</short> > > <description> > - The default policy of "ACCEPT" allows all packets to/from > - interfaces in the zone to be forwarded, while the (*low priority*) > - reject rule blocks any traffic destined for the host, except those > - services explicitly listed (that list can be modified as required > - by the local admin). This zone is intended to be used only by > - libvirt virtual networks - libvirt will add the bridge devices for > - all new virtual networks to this zone by default. > + This zone is intended to be used only by libvirt virtual networks - > + libvirt will add the bridge devices for all new virtual networks to > + this zone by default. > </description> > > -<rule priority='32767'> > - <reject/> > -</rule> > -<protocol value='icmp'/> > -<protocol value='ipv6-icmp'/> > -<service name='dhcp'/> > -<service name='dhcpv6'/> > -<service name='dns'/> > -<service name='ssh'/> > -<service name='tftp'/> > + <forward /> What does '<forward/>' do - i'm not actually finding it mentioned in the zone docs at https://firewalld.org/documentation/man-pages/firewalld.zone.html > </zone> With regards, Daniel -- |: https://berrange.com -o- https://www.flickr.com/photos/dberrange :| |: https://libvirt.org -o- https://fstop138.berrange.com :| |: https://entangle-photo.org -o- https://www.instagram.com/dberrange :|
