On Mon, 2019-07-29 at 18:11 +0100, Daniel P. Berrangé wrote: [...] > +++ b/src/remote/Makefile.inc.am > +remote/virtproxyd.conf: remote/libvirtd.conf.in > + $(AM_V_GEN)sed \ > + -e '/[@]CUT_ENABLE_IP[@]/d' \ > + -e '/[@]END[@]/d' \ > + -e 's/[@]DAEMON_NAME[@]/virtproxyd/' \ > + < $^ > $@ Unnecessary input redirection. [...] > +remote/virtproxyd.aug: remote/libvirtd.aug.in > + $(AM_V_GEN)$(SED) \ > + -e '/[@]CUT_ENABLE_IP[@]/d' \ > + -e '/[@]END[@]/d' \ > + -e 's/[@]DAEMON_NAME[@]/virtproxyd/' \ > + -e 's/[@]DAEMON_NAME_UC[@]/Virtproxyd/' \ > + $< > $@ Same here. [...] > +remote/test_virtproxyd.aug: remote/test_libvirtd.aug.in \ > + remote/virtproxyd.conf $(AUG_GENTEST) > + $(AM_V_GEN)$(AUG_GENTEST) remote/virtproxyd.conf \ > + $(srcdir)/remote/test_libvirtd.aug.in | \ > + $(SED) -e '/[@]CUT_ENABLE_IP[@]/d' \ > + -e '/[@]END[@]/d' \ > + -e 's/[@]DAEMON_NAME[@]/virtproxyd/' \ > + -e 's/[@]DAEMON_NAME_UC[@]/Virtproxyd/' \ > + > $@ || rm -f $@ Wrong formatting for first argument (should be on its own line). [...] > libvirtd.service: remote/libvirtd.service.in $(top_builddir)/config.status > $(AM_V_GEN)sed $(LIBVIRTD_UNIT_VARS) < $< > $@-t && mv $@-t $@ > > libvirt%.socket: remote/libvirt%.socket.in $(top_builddir)/config.status > - $(AM_V_GEN)sed $(LIBVIRTD_UNIT_VARS) < $< > $@-t && mv $@-t $@ > + $(AM_V_GEN)sed $(LIBVIRTD_UNIT_VARS) \ > + < $< > $@-t && mv $@-t $@ Unnecessary input redirection and questionable formatting: $(LIBVIRTD_UNIT_VARS) should be on a separate line. Also, and I'm sorry I've just noticed this, you're using 'sed' instead of $(SED). All three issues trace back to previous patches and should be fixed there. > +virtproxyd.service: remote/virtproxyd.service.in $(top_builddir)/config.status > + $(AM_V_GEN)sed $(VIRTPROXYD_UNIT_VARS) < $< > $@-t && mv $@-t $@ > + > +virtproxy%.socket: remote/libvirt%.socket.in $(top_builddir)/config.status > + $(AM_V_GEN)sed $(VIRTPROXYD_UNIT_VARS) \ > + < $< > $@-t && mv $@-t $@ These rules also suffer from all the issues listed above, but they're introduced by this patch. [...] > +++ b/src/remote/remote_daemon_config.c > @@ -108,7 +108,11 @@ daemonConfigNew(bool privileged ATTRIBUTE_UNUSED) > +# ifdef LIBVIRTD > + data->listen_tls = 1; /* Only honoured it --listen is set */ s/it --listen/if --listen/ -- Andrea Bolognani / Red Hat / Virtualization -- libvir-list mailing list libvir-list@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/libvir-list