[libvirt] RHEL 5 with Xen - changed IPs and now weirdness

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi all,

I had installed RHEL 5 x86_64 with virtualization right off the bat.  Everything ran beautifully with two Xen guests (also RHEL 5.)  All 3 IPs (host and 2 guests) were in the same subnet.

Then I had to change all the IP addresses to a different subnet (but again all 3 within the same subnet - trying to stay away from 802.1q stuff)...  so I modified each guest's /etc/hosts, etc/sysconfig/network, etc/sysconfig/network-scripts/ifcfg-eth0 and then shutdown both guests.  Then modified the configs on the host and rebooted.

When it boots now it seems like it's fine but there is no network connectivity and the default route is pointing to the virbr0 interface!!
ifconfig shows eth0 but without an IP address

If I do a 'service network restart' then everything works fine again, eth0 has the correct IP and the default route is in place.  At that point everything seems fine with the exception of:

I get this every two minutes now:
libvir: Remote error : unable to connect to '/var/run/libvirt/libvirt-sock': Connection refused
libvir: warning : Failed to find the network: Is the daemon running ?
libvir: Remote error : unable to connect to '/var/run/libvirt/libvirt-sock': Connection refused
libvir: Remote error : unable to connect to '/var/run/libvirt/libvirt-sock': Connection refused
libvir: warning : Failed to find a node driver: Is the libvirtd daemon running ?
libvir: Remote error : unable to connect to '/var/run/libvirt/libvirt-sock': Connection refused
libvir: warning : Failed to find the network: Is the daemon running ?
libvir: Remote error : unable to connect to '/var/run/libvirt/libvirt-sock': Connection refused
libvir: Remote error : unable to connect to '/var/run/libvirt/libvirt-sock': Connection refused
libvir: warning : Failed to find a node driver: Is the libvirtd daemon running ?

virt-manager seems to work fine and lists my dom0 and my two xens which also seem to be working just fine.  virsh also seems to have no issues showing my xens:

virsh list
 Id Name                 State
----------------------------------
  0 Domain-0             running
  1 jhsympa1             idle
  2 jhsympa2             idle

xm list also shows no issues:
xm list
Name                                      ID Mem(MiB) VCPUs State   Time(s)
Domain-0                                   0    30050     8 r-----   2596.2
jhsympa1                                   1     1023     1 -b----    159.7
jhsympa2                                   2     1023     1 -b----   4125.3

'service libvirtd status' shows:
libvirtd dead but subsys locked

dmesg doesn't show anything that sticks out other than the fact that eth0 and eth1 seem to be pronounced to be DOWN, then UP, then DOWN, then UP, then DOWN then UP again and again in a time span of a few seconds as different modules start to act - mDNS, xend, bnx iSCSI support, whatever.  But when I compared that to the logs prior to the IP change, they're the same.

I do notice that when I launch virt-manager there is nothing listed in the 'virtual network' tab - it's all greyed out.

SELinux is disabled.  I can't find anything in any configs pertaining to xen or libvirt that are IP related.

I know if this server is rebooted for any reason I'm going to need to do a 'service network restart' before connectivity to/from the guests will work and that's not a good thing!

another error I noticed is:
virsh net-list --all
error: Failed to list active networks
error: this function is not supported by the hypervisor: virConnectNumOfNetworks

whereas xm gives me this:
#xm network-list Domain-0 comes back with nothing
#xm network-list jhsympa1
Idx BE     MAC Addr.     handle state evt-ch tx-/rx-ring-ref BE-path
0   0  00:16:36:32:6e:39    0     4      8     768  /57      /local/domain/0/backend/vif/1/0
# xm network-list jhsympa2
Idx BE     MAC Addr.     handle state evt-ch tx-/rx-ring-ref BE-path
0   0  00:16:36:7b:f3:14    0     4      8     769  /768     /local/domain/0/backend/vif/2/0

Where am I to fix this weirdness?  Changing IPs shouldn't involve all of this!  Especially when I'm only changing eth0 and they are all in the same subnet as before and nothing else was modified.


These guests are about to be put into production and I only have a few days to make changes.
Any help would be awesome!


Thanks
-- 
Denny Snyder
Systems Engineer
IT@Johns Hopkins
5801 Smith Ave Suite 3110C
Baltimore, MD 21209
(410) 735-7613: DESK
(410) 735-4660: FAX
--
Libvir-list mailing list
Libvir-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/libvir-list

[Index of Archives]     [Virt Tools]     [Libvirt Users]     [Lib OS Info]     [Fedora Users]     [Fedora Desktop]     [Fedora SELinux]     [Big List of Linux Books]     [Yosemite News]     [KDE Users]     [Fedora Tools]