On Tue, Jul 17, 2018 at 12:52:40AM -0300, Julio Faracco wrote: > If a domain is configured to start on boot, it has a symlink to the > domain definition inside the autostart directory. If you rename this > domain, the definition is renamed too. The symlink need to be pointed to > this renamed file. This commit recreates the symlink after renaming the > XML file. > > Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1594985 > > Signed-off-by: Julio Faracco <jcfaracco@xxxxxxxxx> > --- > src/qemu/qemu_driver.c | 42 ++++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 42 insertions(+) > > diff --git a/src/qemu/qemu_driver.c b/src/qemu/qemu_driver.c > index 8fae46370e..6bbea324b9 100644 > --- a/src/qemu/qemu_driver.c > +++ b/src/qemu/qemu_driver.c > @@ -20914,6 +20914,8 @@ qemuDomainRenameCallback(virDomainObjPtr vm, > char *old_dom_name = NULL; > char *new_dom_cfg_file = NULL; > char *old_dom_cfg_file = NULL; > + char *new_dom_autostart_link = NULL; > + char *old_dom_autostart_link = NULL; > > virCheckFlags(0, ret); > > @@ -20934,6 +20936,22 @@ qemuDomainRenameCallback(virDomainObjPtr vm, > vm->def->name))) > goto cleanup; > > + if (vm->autostart) { > + if (!(new_dom_autostart_link = virDomainConfigFile(cfg->autostartDir, > + new_dom_name)) || > + !(old_dom_autostart_link = virDomainConfigFile(cfg->autostartDir, > + vm->def->name))) > + goto cleanup; > + > + if (virFileIsLink(old_dom_autostart_link) && > + unlink(old_dom_autostart_link) < 0) { > + virReportSystemError(errno, > + _("Failed to delete symlink '%s'"), > + old_dom_autostart_link); > + goto cleanup; > + } The patch can be further optimized...^this unlink could be done at very last moment after the new config has been defined (if you put it right below the old config unlink). > + } > + > event_old = virDomainEventLifecycleNewFromObj(vm, > VIR_DOMAIN_EVENT_UNDEFINED, > VIR_DOMAIN_EVENT_UNDEFINED_RENAMED); > @@ -20946,6 +20964,16 @@ qemuDomainRenameCallback(virDomainObjPtr vm, > if (virDomainSaveConfig(cfg->configDir, driver->caps, vm->def) < 0) > goto rollback; > > + > + if (vm->autostart) { > + if (symlink(new_dom_cfg_file, new_dom_autostart_link) < 0) { > + virReportSystemError(errno, > + _("Failed to create symlink '%s to '%s'"), > + new_dom_autostart_link, new_dom_cfg_file); > + goto rollback; > + } > + } ...you would then put ^this hunk in the if block above... ... > + if (!virFileExists(old_dom_autostart_link) && > + symlink(old_dom_cfg_file, old_dom_autostart_link) < 0) { > + virReportSystemError(errno, > + _("Failed to create symlink '%s to '%s'"), > + old_dom_autostart_link, old_dom_cfg_file); > + } > + } > + And ^this bit could go away completely. The thing is that usually, you prepare everything ahead and then perform the switch in 1 go to minimize all the places where it can go wrong...same here, you create the new symlink and config and then just simply unlink both the old config and the old symlink - if that fails, you go to rollback where you just simply unlink all the new data that has been created but to which we couldn't successfully switch. Patch looks fine otherwise, so v4 should be pretty straightforward to get in. Thanks, Erik -- libvir-list mailing list libvir-list@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/libvir-list