On 04/20/2017 06:01 AM, Michal Privoznik wrote:
> Basically, whenever the new type of stream packet arrives to the
> daemon call this function that decodes it and calls
> virStreamSkipCallback(). Otherwise a regular data stream packet
> has arrived and therefore continue its processing.
>
> Signed-off-by: Michal Privoznik <mprivozn@xxxxxxxxxx>
> ---
> daemon/stream.c | 81 +++++++++++++++++++++++++++++++++++++++++++++++++--------
> 1 file changed, 70 insertions(+), 11 deletions(-)
>
> diff --git a/daemon/stream.c b/daemon/stream.c
> index 6899c18..84709da 100644
> --- a/daemon/stream.c
> +++ b/daemon/stream.c
> @@ -29,6 +29,7 @@
> #include "virlog.h"
> #include "virnetserverclient.h"
> #include "virerror.h"
> +#include "libvirt_internal.h"
^^
Is this necessary? Doesn't seem so from a test compile I ran w/o it at
least for this patch. Not until patch32 which fails to compile because
virStreamInData isn't defined. At the very least we should wait until
that patch since that's the first time that libvirt_internal.h would be
needed.
Code also has usage of skippable.
>
> #define VIR_FROM_THIS VIR_FROM_STREAMS
>
> @@ -653,6 +654,52 @@ daemonStreamHandleAbort(virNetServerClientPtr client,
> }
>
>
Probably could use some comments similar to other functions here...
> +static int
> +daemonStreamHandleSkip(virNetServerClientPtr client,
> + daemonClientStream *stream,
> + virNetMessagePtr msg)
> +{
> + int ret;
> + virNetStreamSkip data;
> +
> + VIR_DEBUG("client=%p, stream=%p, proc=%d, serial=%u",
> + client, stream, msg->header.proc, msg->header.serial);
> +
> + /* Let's check if client plays nicely and advertised usage of
> + * sparse stream upfront. */
> + if (!stream->skippable) {
> + virReportError(VIR_ERR_RPC, "%s",
> + _("Unexpected stream skip"));
> + return -1;
> + }
> +
> + if (virNetMessageDecodePayload(msg,
> + (xdrproc_t) xdr_virNetStreamSkip,
> + &data) < 0)
> + return -1;
> +
> + ret = virStreamSkip(stream->st, data.length);
would need to grab flags too
> +
> + if (ret < 0) {
> + virNetMessageError rerr;
> +
> + memset(&rerr, 0, sizeof(rerr));
> +
> + VIR_INFO("Stream skip failed");
> + stream->closed = true;
> + virStreamEventRemoveCallback(stream->st);
> + virStreamAbort(stream->st);
A couple of other places where these 3 lines are done all seem to check
(!stream->closed) first.
Of course this does follow daemonStreamHandleWriteData, but figured I'd
note it just in case...
> +
> + return virNetServerProgramSendReplyError(stream->prog,
> + client,
> + msg,
> + &rerr,
> + &msg->header);
> + }
> +
> + return 0;
> +}
> +
>
> /*
> * Called when the stream is signalled has being able to accept
> @@ -671,19 +718,31 @@ daemonStreamHandleWrite(virNetServerClientPtr client,
> virNetMessagePtr msg = stream->rx;
> int ret;
>
> - switch (msg->header.status) {
> - case VIR_NET_OK:
> - ret = daemonStreamHandleFinish(client, stream, msg);
> - break;
> + if (msg->header.type == VIR_NET_STREAM_SKIP) {
> + /* Handle special case when client sent us skip.
s/when/when the/
s/us/us a/
Although some may point out the comment is obvious...
> + * Otherwise just carry on with processing stream
> + * data. */
> + ret = daemonStreamHandleSkip(client, stream, msg);
> + } else if (msg->header.type == VIR_NET_STREAM) {
> + switch (msg->header.status) {
> + case VIR_NET_OK:
> + ret = daemonStreamHandleFinish(client, stream, msg);
> + break;
>
> - case VIR_NET_CONTINUE:
> - ret = daemonStreamHandleWriteData(client, stream, msg);
> - break;
> + case VIR_NET_CONTINUE:
> + ret = daemonStreamHandleWriteData(client, stream, msg);
> + break;
>
> - case VIR_NET_ERROR:
> - default:
> - ret = daemonStreamHandleAbort(client, stream, msg);
> - break;
> + case VIR_NET_ERROR:
> + default:
> + ret = daemonStreamHandleAbort(client, stream, msg);
> + break;
> + }
> + } else {
> + virReportError(VIR_ERR_RPC,
> + _("Unexpected message type: %d"),
> + msg->header.type);
> + ret = -1;
> }
This last hunk (from } else {) is also new and makes me wonder if
perhaps the whole "if () else if () else" should have been done earlier
when VIR_NET_STREAM_SKIP was introduced.
John
>
> if (ret > 0)
>
--
libvir-list mailing list
libvir-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/libvir-list
