On 12/15/2015 04:12 PM, Vlad Yasevich wrote:
On 12/15/2015 02:45 PM, Laine Stump wrote:
On 12/15/2015 01:34 PM, Laine Stump wrote:
On 12/13/2015 10:51 AM, Moshe Levi wrote:
Hi,
I have a setup with libvirt 1.3.0 and OpenStack trunk.
Before launched the VM ip link command show the following VF mac/vlan configuration [1]
When I launch a VM with <interface type='hostdev'> via openstack api (OpenStack direct
port)
I can see that the VF get the mac/vlan according to libvrit xml [2] and ip link
command [3], but when I delete the VM the mac/vlan config are still shown as in [3]
and not restored to [1]
Shouldn’t libvirt restore the mac/vlan to [1].
The same problem exists when using <interface type='direct'> (OpenStack macvtap port)
but just for the MAC configuration of the VF.
What libvirt does is to restore the MAC address to whatever it was before we set it up
for use with a guest. Although there are some sriov net drivers that (for some
unfathomable reason) think it's cool to assign a random MAC address to each VF at boot
time, the "normal" thing is for the VFs to have a MAC address of all 0's to start with.
So libvirt should be saving 00:00:00:00:00:00 (it will be in the file
/var/run/libvirt/hostdevmgr/$ifname_vf$vfnum) then setting the MAC to use; when done,
libvirt will read the 00:00:00:00:00:00 and use netlink to set the MAC address, but this
is apparently failing.
I checked on my Fedora 22 system with the igb driver, and found that if the MAC address
was originally set to something other than 0's, it was restored properly by libvirt, but
if it was set to all 0's originally, the attempt to set it back to 0 would fail.
I then tried doing the same thing with the "ip" utility:
# ip link set dev p4p2 vf 0 mac 00:00:00:00:00:00
and I get the following response:
RTNETLINK answers: Invalid argument
So it appears that either the kernel or the NIC driver is refusing to set the MAC
address to all 0's. I'm reasonably certain this is a regression in the kernel,
Sigh. It appears that this has "always" been the case - I just checked on a 2.6.32-573
RHEL kernel, and a 3.10.x RHEL7.2 kernel, and 4.1 (Fedora 22) and both of them also refuse
to set the MAC address to 00:00:00:00:00:00. I'm not sure if this limitation is in the NIC
driver or some basic code in the kernel.
It's considered to be an invalid address by is_valid_ether_addr() function.
There appear to be different behaviour in some adapters. In current upstream, it looks
like a quarter of the VF capable drivers (bnxt, enic, fm10k, sfc) permit VF mac setting of
all zeros. The others simply use is_valid_ether_addr function without specifically
testing for all-0. I am not sure if this is HW related or simply oversights... Might
want to bringing this up on netdev.
Thanks, Vlad!
Moshe,
It sounds like in your case it is caused by code in the mlx driver, so
hopefully you can have some influence there. My path is a bit more
difficult, as the failure on mine is in the igb driver :-)
Sending a message to netdev is a good idea. It would be wonderful if all
the vendors could agree to:
1) initialize all VFs with a MAC address of 0
2) allow setting VF MAC address to 0 at any time.
I'll put that on my to-do list :-P
-vlad
although I can't say how long it's been there, as I don't normally pay attention to this
(and as I said, many SRIOV NIC drivers don't default their VFs to 0 MAC addresses)
What distro and kernel are you using for your tests?
[1] - 24: enp3s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master
ovs-system state UP mode DEFAULT group default qlen 1000
link/ether e4:1d:2d:a5:f1:22 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 1 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 2 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 3 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
[2] - <interface type='hostdev' managed='yes'>
<mac address=' fa:16:3e:11:af:fe '/>
<driver name='kvm'/>
<source>
<address type='pci' domain='0x0000' bus='0x02' slot='0x00' function='0x7'/>
</source>
<vlan>
<tag id='190'/>
</vlan>
<alias name='hostdev0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</interface>
[3] 24: enp3s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master ovs-system
state UP mode DEFAULT group default qlen 1000
link/ether e4:1d:2d:a5:f1:22 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 1 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 2 MAC 00:00:00:00:00:00, spoof checking off, link-state auto
vf 3 MAC fa:16:3e:11:af:fe, vlan 190, spoof checking off, link-state enable
--
libvir-list mailing list
libvir-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/libvir-list
F15
--
libvir-list mailing list
libvir-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/libvir-list
--
libvir-list mailing list
libvir-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/libvir-list