Kiarie Kahurani (1):
src/xenconfig: XL parser
po/POTFILES.in | 1 +
src/Makefile.am | 3 +-
src/libvirt_xenconfig.syms | 5 +
src/libxl/libxl_driver.c | 44 ++-
src/xenconfig/xen_common.c | 140 ++++----
src/xenconfig/xen_common.h | 24 +-
src/xenconfig/xen_xl.c | 461 ++++++++++++++++++++++++++
src/xenconfig/xen_xl.h | 29 ++
tests/Makefile.am | 9 +-
tests/testutilsxen.c | 50 +++
tests/testutilsxen.h | 9 +-
tests/xlconfigdata/test-fullvirt-new-disk.cfg | 27 ++
tests/xlconfigdata/test-fullvirt-new-disk.xml | 46 +++
tests/xlconfigtest.c | 222 +++++++++++++
14 files changed, 981 insertions(+), 89 deletions(-)
create mode 100644 src/xenconfig/xen_xl.c
create mode 100644 src/xenconfig/xen_xl.h
create mode 100644 tests/xlconfigdata/test-fullvirt-new-disk.cfg
create mode 100644 tests/xlconfigdata/test-fullvirt-new-disk.xml
create mode 100644 tests/xlconfigtest.c
After *toooo* long the xen-xl parser has arrived with support for
xl disk format and spice graphics(with admittedly very kludgy code)
quick overview
1)coverts xl disk config such as
disk = ["/dev/sda,raw,hda,rw,"]
into xml config
<disk type='block' device='disk'>
<driver name='phy'/>
<source dev='/dev/sda/'>
<target dev= 'hda' bus='ide'/>
</disk>
and vice-versa
You notice that in the xl disk config there is no driver type but
it appears on the xml; I use the format to intelligently guess the
driver but this does not look very good again you notice I do not
support disk backend config which is because there is no member of
_virDomainDiskDef which I could relate to the backend
2)converts spice graphics config
spice = 1
spicehost = "127.0.0.1"
spiceport = 500
spicetls_port = 590
spicedisable_ticketing = 1 #with this set you require a passwd
spicepasswd = "thebeast"
spiceagent_mouse = 1
to
<graphics type='spice' port='500' tlsPort='590' autoport='no' listen='127.0.0.1'>
<listen type='address' address='127.0.0.1'/>
<mouse mode='server'/>
and vice-versa
You notice that the passwd is not in the xml, am still trying to figure out why
Again you will notice the current tests are a bit dependent on xen code(when
initializing the xmlOpt) which would *better* be done away with but that would
require some code in src/libxl/
Into the bargain, am not *sure* how exactly to initialize _virCapsPtr which is
reqiured for xml formatting because I *assume* that tests should be able to run
even with drivers not loaded.
Am also not *sure* that how to map disks to device type, the existing code(xm)
code maps all the disks using another driver other than 'phy' to 'block'.Am not
sure this is correct.
With the current patch
$virsh domxml-from/to-native xen-xl works perfectly
TODO
Fix tests
--
1.8.4.5
--
libvir-list mailing list
libvir-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/libvir-list