I created a new network based on the default network. However the network
is unreachable to the XEN guest.
I used net-dumpxml to print the "default" xml. I changed the network XML
network name, bridge name, and uuid
and successfully created a new network. I replaced source network
attribute in the domain creation XML to point to the new network name.
However, the guest can not properly initialize eth0 because the new network
is unreachable.
It tries to ping the ip assigned to the new bridge but fails. The same
guest created with the default network works
fine, i.e. it can access the network.
This what network restart looks like on the guest (I'm not sure if this
will be visible on the forum):
(Embedded image moved to file: pic26442.jpg)
This is a copy of the network XML:
<network>
<name>test-net1</name>
<uuid>7cfbfa88-542f-44c7-bbc1-3e19f67d8ca6</uuid>
<forward mode='nat'/>
<bridge name='test-br1' stp='on' forwardDelay='0' />
<ip address='192.168.122.1' netmask='255.255.255.0'>
<dhcp>
<range start='192.168.122.2' end='192.168.122.254' />
</dhcp>
</ip>
</network>
This the interface segment domain creation XML:
<interface type='network'>
<!--source network='default'/-->
<source network='test-net1'/>
<script path='vif-bridge'/>
</interface>
This is the relevant ifconfig on host:
....
test-br1 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet addr:192.168.122.1 Bcast:192.168.122.255
Mask:255.255.255.0
inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:81 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9768 (9.5 KiB) TX bytes:5018 (4.9 KiB)
vif13.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:90 errors:0 dropped:0 overruns:0 frame:0
TX packets:194 errors:0 dropped:2771 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:11136 (10.8 KiB) TX bytes:10122 (9.8 KiB)
virbr0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
inet addr:192.168.122.1 Bcast:192.168.122.255
Mask:255.255.255.0
inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:365 errors:0 dropped:0 overruns:0 frame:0
TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:34127 (33.3 KiB) TX bytes:512877 (500.8 KiB)
This the brctl show output:
bridge name bridge id STP enabled interfaces
br1 8000.000000000000 no
eth1 8000.001a64a12e56 no peth1
test-br1 8000.feffffffffff yes vif13.0
virbr0 8000.000000000000 yes
What am I missing?
Thanks in advance.
-Kenneth Nagin
Attachment:
pic26442.jpg
Description: JPEG image
-- Libvir-list mailing list Libvir-list@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/libvir-list