Hi,, I kinda jumped off of the group for a "personal" question. I'm using Dell 2950's which have a BroadComm nic. Dell says use Open Manage (which is not an option for me) When I did this manually (CD ISO's) the software from Dell actually did a kernel re-compile!! Any ideas? thanks Rick Leonhardt Belo Interactive System Admin 214 977 4815 -----Original Message----- From: Shabazian, Chip [mailto:Chip.Shabazian@xxxxxxxxxxxxxxxxx] Sent: Thursday, January 11, 2007 2:52 PM To: Discussion list about Kickstart Subject: RE: the driverdisk option in the .cfg file Actually, you can access the driver over the network if the NIC successfully PXEBoots. Either add it to the initrd that gets loaded, or load it via the commandline. I ran into a situation where we needed to do this a long time ago, but we couldn't change the update level that we were building from. The easiest solution was to bust open the initrd, and swap out loader from a more recent initrd that had the driver. As for the online documentation, to say that it is basic is a kind statement. I'm hoping to create a much more technical brief on kickstart over the next few months, if time permits. Along those lines, I'll be asking people to send me their tips/tricks that they have learned over the years. Chip -----Original Message----- From: kickstart-list-bounces@xxxxxxxxxx [mailto:kickstart-list-bounces@xxxxxxxxxx] On Behalf Of Ray Van Dolson Sent: Thursday, January 11, 2007 12:45 PM To: Discussion list about Kickstart Subject: Re: the driverdisk option in the .cfg file On Thu, Jan 11, 2007 at 01:42:28PM -0700, Harner Keith-FKH006 wrote: > > Sure, > > I get: > *ASSERT: no network device in choosenetworkinterface *Unable to bring > up network > > So even though the host will PXE load a kernel it still cannot get to > a network resource? Oooh. Well, looks like there is no built-in driver support for your network cards. :) You'll need a driver disk for that as well likely. You may need to modify your installation CD in order to include this driver as there's no way to access it across the network without the NIC's working :D That or actually provide a physical driver disk, but that kind of negates the benefits of a hands-off Kickstart install. > My goal is to eliminate the need for a driver disk at boot time as we > run XCat and routinely have users reboot to upgrade their workstations. > > Thanks, > > Keith Harner > Engineering Compute > Phone: 480-413-8625 > Pager: 7393862@xxxxxxxxxx > > > > > -----Original Message----- > From: kickstart-list-bounces@xxxxxxxxxx > [mailto:kickstart-list-bounces@xxxxxxxxxx] On Behalf Of Ray Van Dolson > Sent: Wednesday, January 10, 2007 5:06 PM > To: Discussion list about Kickstart > Subject: Re: the driverdisk option in the .cfg file > > On Wed, Jan 10, 2007 at 05:05:23PM -0700, Harner Keith-FKH006 wrote: > > I recently received some new Sun Ultra 20 m2 workstations. > > Our current supported release RHEL3 update 7 does not contain > > drivers for this new hardware. > > > > I attempted to utilize the driverdisk option in the .cfg file and > > point to an NFS exported directory containing all of the needed > drivers. > > > > driverdisk --source=nfs:host_ip:path_to_drivers > > > > For some reason it cannot seem to find the drivers although the path > > is valid and any host can mount it. > > > > What am I missing? > > Keith, are you seeing any error messages in any of the console screens > you could share with us? > > Ray _______________________________________________ Kickstart-list mailing list Kickstart-list@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/kickstart-list
