|
The server receives an address during PXE:
output from syslog: Oct 7 16:10:24 edcappsrhat7 dhcpd:
DHCPDISCOVER from 00:14:c2:3c:a9:d2 via eth0 Oct 7 16:10:24 edcappsrhat7 dhcpd:
DHCPOFFER on 10.xxx.xxx.xxx to 00:14:c2:3c:a9:d2 via eth0 Oct 7 16:10:28 edcappsrhat7 dhcpd: DHCPREQUEST
for 10.xxx.xxx.xxx (10.xxx.xxx.xxx) from 00:14:c2:3c:a9:d2 via eth0 Oct 7 16:10:28 edcappsrhat7 dhcpd:
DHCPACK on 10.xxx.xxx.xxx to 00:14:c2:3c:a9:d2 via eth0 Oct 7 20:10:28 edcappsrhat7
in.tftpd[9102]: RRQ from 10.xxx.xxx.xxx filename pxelinux.0 Oct 7 20:10:28 edcappsrhat7
in.tftpd[9102]: tftp: client does not accept options Oct 7 20:10:28 edcappsrhat7
in.tftpd[9103]: RRQ from 10.xxx.xxx.xxx filename pxelinux.0 Oct 7 20:10:28 edcappsrhat7
in.tftpd[9104]: RRQ from 10.xxx.xxx.xxx filename pxelinux.cfg/01-00-14-c2-3c-a9-d2 Oct 7 20:10:28 edcappsrhat7
in.tftpd[9104]: sending NAK (1, File not found) to 10.xxx.xxx.xxx Oct 7 20:10:28 edcappsrhat7
in.tftpd[9105]: RRQ from 10.xxx.xxx.xxx filename pxelinux.cfg/0xxxxxx Oct 7 20:12:03 edcappsrhat7 in.tftpd[9224]:
RRQ from 10.xxx.xxx.xxx filename vmlinuz Oct 7 20:12:03 edcappsrhat7
in.tftpd[9225]: RRQ from 10.xxx.xxx.xxx filename initrd.img Then it starts the process and dies with
the message I posted earlier. It just hangs at the: Welcome to Red Hat Configure TCP/IP screen Thanks. Liz Brosch TSH System Services office: (215) 386-0100 x1144 cell: (267)
784-9166 From:
kickstart-list-bounces@xxxxxxxxxx [mailto:kickstart-list-bounces@xxxxxxxxxx] On Behalf Of Shabazian, Chip Do you get an address when you boot from
disk 1 or the boot.iso? From:
kickstart-list-bounces@xxxxxxxxxx [mailto:kickstart-list-bounces@xxxxxxxxxx] On Behalf Of Elizabeth.Brosch@xxxxxxxxxxx Thanks for the reply Chip but it
didn’t work. I received the same error. Liz From:
kickstart-list-bounces@xxxxxxxxxx [mailto:kickstart-list-bounces@xxxxxxxxxx] On Behalf Of Shabazian, Chip Will this server get a dhcp address if you
boot from the boot.iso (or disk 1 with askmethod) and select http, ftp or nfs
as your install path? If so, you are probably running into a
switch timing issue that I have to deal with every day. Try adding an
ethtool option to the end of your command line: if 100MB Full Duplex: ksdevice=eth0
eth0_ethtool="autoneg=off speed=100 duplex=full" If 1000MB Full: ksdevice=eth0
eth0_ethtool="autoneg=on speed=1000 duplex=full" Chip From:
kickstart-list-bounces@xxxxxxxxxx [mailto:kickstart-list-bounces@xxxxxxxxxx] On Behalf Of Elizabeth.Brosch@xxxxxxxxxxx I have been trying to get kickstart working but have had no
success. Here are the last few lines of the kickstart process before
it dies: *getting kickstart file *sending dhcp request through device eth0 *waiting for link * 5 seconds * running dhcp for eth0 * pump told us: No DHCP reply received * eth0 isn’t a wireless adaptor I have checked every possible configuration with regards to
dhcp, pxe, tftp, but cannot find anything wrong. Has anyone else seen this type of behavior? Thanks in advance. Liz Brosch TSH System Services office: (215) 386-0100 x1144 cell: (267) 784-9166 |
