Thanks a lot for your reply I'll get back to you soon, after working on that. Thanks a lot On Tue, 08 Feb 2005 10:45:56 -0600, Peter Eisch <peter@xxxxxxxx> wrote: > > If you look at 'pivotroot' down in the source, you'll see that stage2.img > gets mounted as the new / during the install. Whatever drivers you updated > in initrd.img will also need to be updated on the new / image loaded from > stage2.img. > > What Drivers? ... the drivers for whatever controller your target install > disk is connected. > > On 2/8/05 10:36 AM, "Jaswinder Singh Kohli" <jskohli@xxxxxxxxx> wrote: > > > Installing only bare minimum system, to act as gateway and proxy server. > > All the partitions are correctly formatted. > > > > I am using stripped down, buildinstall which only updates, initrd.img > > and not the other files. > > > > Since building stage2.img using buildinstall, requires lot of other > > packages to be in the > > install tree, for X and others, which i dont' want to include, as it > > is for proxy server > > and very small image. > > > > And what kind of drivers ??? > > > > > > On Tue, 08 Feb 2005 10:16:05 -0600, Peter Eisch <peter@xxxxxxxx> wrote: > >> > >> You probably don't have drivers for that particular kernel that you are now > >> booting from in the stage2.img. Whatever you did to update the boot > >> initrd.img, also do to the stage2.img. > >> > >> peter > >> > >> On 2/8/05 6:18 AM, "Jaswinder Singh Kohli" <jskohli@xxxxxxxxx> wrote: > >> > >>> Hi, > >>> > >>> I am getting this error while installation, using the ks.cfg which > >>> partitions the drive into > >>> three partitions, / = 1 G > >>> swap = 1 G > >>> /var = rest of space ( 30 + G) > >>> > >>> The cd image that i built had modified stage2.img, ( took care of > >>> .buildstamp) > >>> bootdisks upgraded to kernel 2.6.10..., > >>> Only Modified isolinux/initrd.img is used, rest of the files like, > >>> stage2.img and hdstg2.img > >>> are just repackaged version of what were on Original FC3 Iso's, only > >>> changed .buildstamp > >>> > >>> Now when i booot that CD, the boots up, detects hardware, anaconda starts X > >>> The partitions are created and formatted, but then the Install ends > >>> with a message. > >>> > >>> "An error occured while transfering install image to your harddrive . > >>> You are probably > >>> out of disk space" > >>> > >>> Where as when i perform fdisk -l on tty2, which shows, all the > >>> partitions were created > >>> and also on console 6 the formatting was successful and hence lot of > >>> space is there. > >>> > >>> On tty3, the detailed error message is as follows... > >>> > >>> Error transfering stage2.img: [Errno 2] No such file of directory: > >>> '/mnt/sysimage/proc/rhinstall-stage2.img' > >>> > >>> I did a search on google, and archives, came up with no results. > >>> > >>> Can any one tell me what i am missing or doing wrong and why it is > >>> trying to copy > >>> rhinstall-stage2.img from some proc fs instead of stage2.img from CD. > >>> > >>> I am stuck at this point for too long now, any Pointers, any ideas, > >>> will be helpful, that can > >>> get me going in forward direction. > >>> > >>> Thanks.... > >> > >> _______________________________________________ > >> Kickstart-list mailing list > >> Kickstart-list@xxxxxxxxxx > >> https://www.redhat.com/mailman/listinfo/kickstart-list > >> > > > > _______________________________________________ > Kickstart-list mailing list > Kickstart-list@xxxxxxxxxx > https://www.redhat.com/mailman/listinfo/kickstart-list > -- Regards JSK jskohli (AT) gmail (DOT) com
