The "df" command gives me this:
-----
bash.1[~]: df
Filesystem 1K-blocks Used Available Use% Mounted on
devtmpfs 8174992 0 8174992 0% /dev
tmpfs 8186908 27688 8159220 1% /dev/shm
tmpfs 8186908 1808 8185100 1% /run
tmpfs 8186908 0 8186908 0% /sys/fs/cgroup
/dev/sda6 51475068 30103124 18734120 62% /
tmpfs 8186908 28 8186880 1% /tmp
/dev/sda3 487652 215053 242903 47% /boot
/dev/sda7 947624164 8118256 891346268 1% /home
tmpfs 1637380 24 1637356 1% /run/user/0
bash.2[~]
-----
The "smartctl" command with a parameter of "sda3" gives me this:
-----
bash.7[~]: smartctl -a /dev/sda3
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.14.13-200.fc26.x86_64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST2000DM006-2DM164
Serial Number: Z4Z89YG1
LU WWN Device Id: 5 000c50 0a3169115
Firmware Version: CC26
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Jan 24 15:08:04 2018 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 80) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 207) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x1085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 162318392
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 524
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 073 060 030 Pre-fail Always - 24305368
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 2614
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 524
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 063 058 045 Old_age Always - 37 (Min/Max 36/39)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 074 074 000 Old_age Always - 53764
194 Temperature_Celsius 0x0022 037 042 000 Old_age Always - 37 (0 17 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 1717 (118 144 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1779480900
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 88879919912
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5 -
# 2 Short offline Completed without error 00% 3 -
# 3 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
bash.8[~]:
-----
This looks like the output I was getting last spring, when the old hard drive was dying. The current drive, a new drive, was installed at that time (late June). It's as if smartctl is at least in part simply re-displaying results from the last run I did on the old drive last June.
Also, the output is basically the same whether the smartctl parameter is "sda", "sda3", or "sd?".
The "Disks" I was referring to is what Samuel identified.
_______________________________________________
users mailing list -- users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to users-leave@xxxxxxxxxxxxxxxxxxxxxxx
