Humm,
not too good.
This dongle works fine with fedora 20
This is the output of mmcli with fedora 20 after I give the PIN number
-------------------------
Hardware | manufacturer: 'TCT Mobile International Limited'
| model: 'HSPA+ Data Card'
| revision: 'GX120K00XX'
| supported: 'gsm-umts'
| current: 'gsm-umts'
| equipment id: '356698042474859'
-------------------------
System | device: '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-6'
| drivers: 'option1'
| plugin: 'X22X'
| primary port: 'ttyUSB4'
| ports: 'ttyUSB3 (at), ttyUSB4 (at)'
-------------------------
Numbers | own : 'unknown'
-------------------------
Status | lock: 'none'
| unlock retries: 'unknown'
| state: 'disabled'
| power state: 'on'
| access tech: 'unknown'
| signal quality: '0' (cached)
-------------------------
Modes | supported: 'allowed: 2g; preferred: none
| allowed: 3g; preferred: none
| allowed: 2g, 3g; preferred: none'
| current: 'allowed: any; preferred: none'
-------------------------
Bands | supported: 'unknown'
| current: 'unknown'
-------------------------
IP | supported: 'ipv4'
-------------------------
3GPP | imei: '356698042474859'
| enabled locks: 'sim, net-pers'
| operator id: 'unknown'
| operator name: 'unknown'
| registration: 'unknown'
-------------------------
SIM | path: '/org/freedesktop/ModemManager1/SIM/0'
Hardware | manufacturer: 'TCT Mobile International Limited'
| model: 'HSPA+ Data Card'
| revision: 'GX120K00XX'
| supported: 'gsm-umts'
| current: 'gsm-umts'
| equipment id: '356698042474859'
-------------------------
System | device: '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-6'
| drivers: 'option1'
| plugin: 'X22X'
| primary port: 'ttyUSB4'
| ports: 'ttyUSB3 (at), ttyUSB4 (at)'
-------------------------
Numbers | own : 'unknown'
-------------------------
Status | lock: 'none'
| unlock retries: 'unknown'
| state: 'disabled'
| power state: 'on'
| access tech: 'unknown'
| signal quality: '0' (cached)
-------------------------
Modes | supported: 'allowed: 2g; preferred: none
| allowed: 3g; preferred: none
| allowed: 2g, 3g; preferred: none'
| current: 'allowed: any; preferred: none'
-------------------------
Bands | supported: 'unknown'
| current: 'unknown'
-------------------------
IP | supported: 'ipv4'
-------------------------
3GPP | imei: '356698042474859'
| enabled locks: 'sim, net-pers'
| operator id: 'unknown'
| operator name: 'unknown'
| registration: 'unknown'
-------------------------
SIM | path: '/org/freedesktop/ModemManager1/SIM/0'
And in fedora 22 (it never ask me for the PIN)
-------------------------
Hardware | manufacturer: 'TCT Mobile International Limited'
| model: 'HSPA+ Data Card'
| revision: 'GX120K00XX'
| supported: 'gsm-umts'
| current: 'gsm-umts'
| equipment id: '356698042474859'
-------------------------
System | device: '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-6'
| drivers: 'option1'
| plugin: 'X22X'
| primary port: 'ttyUSB4'
| ports: 'ttyUSB3 (at), ttyUSB4 (at)'
-------------------------
Numbers | own : 'unknown'
-------------------------
Status | lock: 'sim-pin'
| unlock retries: 'unknown'
| state: 'locked'
| power state: 'on'
| access tech: 'unknown'
| signal quality: '0' (cached)
-------------------------
Modes | supported: 'allowed: any; preferred: none'
| current: 'allowed: any; preferred: none'
-------------------------
Bands | supported: 'unknown'
| current: 'unknown'
-------------------------
IP | supported: 'none'
-------------------------
SIM | path: '/org/freedesktop/ModemManager1/SIM/2'
Hardware | manufacturer: 'TCT Mobile International Limited'
| model: 'HSPA+ Data Card'
| revision: 'GX120K00XX'
| supported: 'gsm-umts'
| current: 'gsm-umts'
| equipment id: '356698042474859'
-------------------------
System | device: '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-6'
| drivers: 'option1'
| plugin: 'X22X'
| primary port: 'ttyUSB4'
| ports: 'ttyUSB3 (at), ttyUSB4 (at)'
-------------------------
Numbers | own : 'unknown'
-------------------------
Status | lock: 'sim-pin'
| unlock retries: 'unknown'
| state: 'locked'
| power state: 'on'
| access tech: 'unknown'
| signal quality: '0' (cached)
-------------------------
Modes | supported: 'allowed: any; preferred: none'
| current: 'allowed: any; preferred: none'
-------------------------
Bands | supported: 'unknown'
| current: 'unknown'
-------------------------
IP | supported: 'none'
-------------------------
SIM | path: '/org/freedesktop/ModemManager1/SIM/2'
-------------------------
Bearers | paths: 'none'
Bearers | paths: 'none'
here is the ifconfig of fedora 20
em1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:14:22:f8:91:72 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 17
ether 00:14:22:f8:91:72 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 17
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 856 bytes 66444 (64.8 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 856 bytes 66444 (64.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 856 bytes 66444 (64.8 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 856 bytes 66444 (64.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
ppp0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1500
inet 10.159.32.93 netmask 255.255.255.255 destination 10.64.64.64
ppp txqueuelen 3 (Point-to-Point Protocol)
RX packets 16 bytes 1079 (1.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 18 bytes 769 (769.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
inet 10.159.32.93 netmask 255.255.255.255 destination 10.64.64.64
ppp txqueuelen 3 (Point-to-Point Protocol)
RX packets 16 bytes 1079 (1.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 18 bytes 769 (769.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
And the one of fedora 22
em1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:14:22:f8:91:72 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 17
ether 00:14:22:f8:91:72 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 17
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:2d:9f:e3 txqueuelen 0 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:2d:9f:e3 txqueuelen 0 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Can I configure ppp0 manually?
===========================================================================
Patrick DUPRÉ | | email: pdupre@xxxxxxx
Laboratoire de Physico-Chimie de l'Atmosphère | |
Université du Littoral-Côte d'Opale | |
Tel. (33)-(0)3 28 23 76 12 | | Fax: 03 28 65 82 44
189A, avenue Maurice Schumann | | 59140 Dunkerque, France
===========================================================================
Patrick DUPRÉ | | email: pdupre@xxxxxxx
Laboratoire de Physico-Chimie de l'Atmosphère | |
Université du Littoral-Côte d'Opale | |
Tel. (33)-(0)3 28 23 76 12 | | Fax: 03 28 65 82 44
189A, avenue Maurice Schumann | | 59140 Dunkerque, France
===========================================================================
Sent: Sunday, August 02, 2015 at 9:22 PM
From: "Paul Cartwright" <pbcartwright@xxxxxxxxx>
To: "Patrick Dupre" <pdupre@xxxxxxx>
Subject: Re: Mobile Broadand
From: "Paul Cartwright" <pbcartwright@xxxxxxxxx>
To: "Patrick Dupre" <pdupre@xxxxxxx>
Subject: Re: Mobile Broadand
On 08/02/2015 01:07 PM, Patrick Dupre wrote:
It is an onetouch Alcatel
lots of google hits for alcatel & linux.. I never found a good answer..
http://alcatelonetouch.com/global-en/support/faq/datacard.html
- Q2Is my modem compatible with Windows / Mac / Linux OS?
Alcatel Modems are compatible with Windows / Mac OS. Detailed specifications might be different according to different models. Please find the detailed information on the Alcatel Website:
http://www.alcatelonetouch.com/global-en/products/mobile_broadband.html
http://www.draisberghof.de/usb_modeswitch/bb/viewtopic.php?f=3&t=2110
Tried Alcatel OT X602D with Fedora 22, CentOS 6.5 and Fedora 20. No luck at all.
Fedora 22 have a record for it, but end with segfault:
Fedora 19 32bit with glibc-2.17 and latest usb_modeswitch - segfault in libc-2.17...
-- Paul Cartwright -- Paul Cartwright Registered Linux User #367800 and new counter #561587
-- users mailing list users@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe or change subscription options: https://admin.fedoraproject.org/mailman/listinfo/users Fedora Code of Conduct: http://fedoraproject.org/code-of-conduct Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines Have a question? Ask away: http://ask.fedoraproject.org
