Re: Need help for F18 with Canon LBP2900

Khemara Lyn <lin.kh@xxxxxxxxxxxx> · Wed, 03 Jul 2013 13:33:10 +0700

    Dear Ed and all,

      I managed to make it work by reading the documentation in deep.
      The problem was this:

      As said in the readme file of the Doc directory that comes with
      the CATP driver package,

      I had to use -P <full-path-to-the-PPD-file>:

      /usr/sbin/lpadmin -p LBP5000 -P
      /usr/share/cups/model/CNCUPSLBP5000CAPTK.ppd -v
      ccp://localhost:59687 -E

      while the instructions I found on Google use the -m:

      /usr/sbin/lpadmin -p LBP2900 -m
        CNCUPSLBP2900CAPTK.ppd -v ccp://localhost:59787 -E

      To summarize the steps as this may benefits someone else later:

      - Download and install CAPT driver package from here:

http://www.canon-europe.com/Support/Consumer_Products/products/printers/Laser/i-SENSYS_LBP2900.aspx?type=download&page=1

      - Register the printer with this command:

      /usr/sbin/lpadmin -p LBP5000 -P
      /usr/share/cups/model/CNCUPSLBP5000CAPTK.ppd -v
      ccp://localhost:59687 -E

      where the PPD file got placed in the folder /usr/share/cups/model/
      by the driver package installed in the above step.

      - Start the CCP daemon:

      /etc/init.d/ccpd start

      - Print a TestPage

      I could also use the "Add Printer" link from the CUPS Web page
      http://localhost:631/admin and specifying the correct Device URI
      (ccp://localhost:59787/) and selecting the correct PPD file
      (/usr/share/cups/model/CNCUPSLBP5000CAPTK.ppd).

      If TestPage does not work, try to restart the printer. 

      I found that, when I plug in the printer, the CUPS system
      adds/installs automatically; however that one does not work and if
      I tried to print TestPage with it; I won't work and mess it all
      up: the printer won't print any more even with the correct setup I
      had before. I need to restart the printer to make it work again.

      That is all my observations.

      Now, I need a little more help: how can I disable the automatic
      adding/installing of printer by CUPS?

      I tried with "Browsing Off" in /etc/cups/cupsd.conf" but did not
      do it.

      Again, thanks for all the help so far, very much appreciated.

      Regards,

      Khem

      On 07/03/2013 10:12 AM, Ed Greshko wrote:

      On 07/03/13 10:59, Ed Greshko wrote:

        On 07/03/13 10:40, Ed Greshko wrote:

          On 07/03/13 10:22, Khemara Lyn wrote:

            Yes, this printer was bought here, in Cambodia.
Even so, is there a solution. How can i make the printer work with F18?

          What I would do is....

1.  Download this from canon...
     http://www.canon-europe.com/Support/Consumer_Products/products/printers/Laser/i-SENSYS_LBP2900.aspx?DLtcmuri=tcm:13-1060371&page=1&type=download

2.  Un-tar the download....

3.  Then go to where you un-tared ..../Linux_CAPT_PrinterDriver_V256_uk_EN/Doc

4.  Un-tar guide-capt-2.56UK.tar.gz and then point your browser to file://...../guide-capt-2.56UK/index

They seem to have put a fair amount of effort into documentation.

        Please note that the instructions are prior to the introduction of "systemd".  So, you'll need to adjust for that.  It may be "slightly" more complex.

      http://www.canon-europe.com/Support/Consumer_Products/contact_support/Index.aspx

may also come in handy.....  

-- 
users mailing list
users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe or change subscription options:
https://admin.fedoraproject.org/mailman/listinfo/users
Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
Have a question? Ask away: http://ask.fedoraproject.org