On 11/22/2012 02:38 PM, Ranjan Maitra wrote:
On Thu, 22 Nov 2012 15:57:46 -0600 Ranjan Maitra
<maitra.mbox.ignored@xxxxxxxxx> wrote:
Hi,
Following up on my previous e-mail, I wanted to mention that two usb
interfaces are being recognized. Here is the relevant output of
% usb-devices
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 15 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0bb4 ProdID=0c02 Rev=02.22
S: Manufacturer=ARNOVA 10
S: Product=ARNOVA 10
S: SerialNumber=11223344
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=256mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42
Prot=01 Driver=(none)
I want to mount this as a USB storage device, so that i can access the
filesystem.
Question: How do I mount the first interface?
Sorry to add to my e-mail, the output of lsusb -v is as follows:
$ lsusb -v -s 001:024
Bus 001 Device 024: ID 0bb4:0c02 High Tech Computer Corp. Dream /
ADP1 / G1 / Magic / Tattoo (Debug) Couldn't open device, some
information will be missing Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0bb4 High Tech Computer Corp.
idProduct 0x0c02 Dream / ADP1 / G1 / Magic / Tattoo (Debug)
bcdDevice 2.22
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 55
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 256mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
And the output of:
$ lsusb -D /dev/bus/usb/001/001
Device: ID 1d6b:0002 Linux Foundation 2.0 root hub
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 3.06
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
and
$ lsusb -D /dev/bus/usb/001/024
Device: ID 0bb4:0c02 High Tech Computer Corp. Dream / ADP1 / G1 /
Magic / Tattoo (Debug) Couldn't open device, some information will be
missing Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0bb4 High Tech Computer Corp.
idProduct 0x0c02 Dream / ADP1 / G1 / Magic / Tattoo (Debug)
bcdDevice 2.22
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 55
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 256mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
All I want to do is to be able to mount the usb as a storage device and
then edit files in it.
Many thanks again and best wishes,
Ranjan
I didn't catch your original email, so please excuse if I answer a
question you didn't ask.
You want to mount a usb device that for some reason doesn't automount?
Try these commands in a console window:
[1] unplug the usb device
[2] > ls /dev
[3] plug in the device
[4] > ls /dev
Now identify the new device in /dev by comparing the output from [2] and
[4].
There should be a new device (probably) named /dev/sd?n - where "?" is a
letter ("a" - "z") and "n" is a number.
There should be multiple devices, the device without a number, and 1 or
more devices, one for each partition
in the devices's filesystem. If the device has no partitions, the you
only get /dev/sd?.
On my box, I always get devices "/dev/sdd" and "/dev/sdd1", but it
depends on the storage devices in your system.
This information should also be in /var/log/messages.
If a new device doesn't appear in /dev, then someone smarter than me
will be required.
[5] > mkdir <some-directory> - I usually do > mkdir X
[6] > sudo mount /dev/sd?n (or /dev/sd?) <some-directory>
If it fails to mount, then you should check the mount manpage for some
options that might help ( -t ), but
mount usually does the right thing.
You could also post the output of [6] to this list and someone will
figure it out.
Regards,
John
--
users mailing list
users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe or change subscription options:
https://admin.fedoraproject.org/mailman/listinfo/users
Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
Have a question? Ask away: http://ask.fedoraproject.org
