Re: dhcpd gateway settings

[Aaron Gray <aaronngray.lists@xxxxxxxxx>]

On 22 April 2011 21:45, James Wilkinson <fedora@xxxxxxxxxxxxxxxxxx> wrote:

Aaron Gray wrote:
> I am trying to set up a network and gateway on 192.168.1.x that I am using
> for BOOTP'ing servers.
<snip>
> But I cannot seem to get HTTP or other services to work on 192.168.1.x
>
> I have the existing 192.168.0.x network and was wondering how gateway
> requests should get from 192.168.1.x to 192.168.0.1 ?

I asked:

> How is this physically laid out?
>

> Are the two networks physically separate, and the gateway has two
> network cards (and hence is on both networks)?

Aaron replied:

> I have dhcpd running on a laptop with one network controller.
>

> No, all on the same physical network.

I asked:

> Do you have forwarding turned on on the gateway?

Aaron replied:
> No

That might be a good place to start.

Okay is that IPTables or routing ?

I asked:

> Does the gateway also have the connection to the Internet, or is this
> from another device?

Aaron replied:

> I want it to work as device 192.168.0.140

OK: I don’t quite think I understand this. Unless this is to be a
standalone network (and you mention Google, so…) something’s got to have
a connection to the Internet.

I have a Netgear router serving 192.168.0.x and the laptop is at static IP address 192.168.0.140.

If the laptop has a connection of its own to the Internet (say a 3G
dongle or a USB ADSL modem), what you would want is something like this:

       Internet
           ^
           |
           |
         laptop
          /   \
         /     \
        /       \
192.168.0/24   192.168.1/24

I want the laptop to serve as a gateway between the 192.168.0.x and 192.168.1.x subnets, so it can serve BOOTP and TFTP to provide PXE booting for diskless servers.

 

Then all the devices on 192.168.0/24 should have 192.168.0.140 as their
gateway (assuming that’s the laptop’s IP address). You’d probably also
have NAT already turned on.

No the Netgear router provides 192.168.0.1 and 192.168.0.140 is the static IP address of the laptop.

If, on the other hand, you’ve got a separate router (say an ADSL
router), then what you’ve got is something like this:

Internet <—–> router <—–> 192.168.1/24 <—–> laptop <—–> 192.168.0/24

yep, but all on one physical network.

 

Then you’ve got a problem for all the other devices on 192.168.1/24.
They know that anything on 192.168.1/24 is local, and should just be
sent on the local network. They “know” that anything else is on the
Internet, and should be sent to the router.

Okay.

 

So, in particular, anything on 192.168.0/24 isn’t local to them, and
gets sent to the router, not the laptop.

 

Yes 

What you need to do is to tell everything on 192.168.1/24 to use a
static route: packets to 192.168.0/24 should go to the laptop’s IP
address.

?

 

You might find it easier to get this working with static IP addresses
first, then replicate that with DHCP.

I need DHCP to serve the BOOTP protocol, so static IP's other than the laptops don't really help.

 

Hope this helps,

Thanks,

Aaron

-- 
users mailing list
users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe or change subscription options:
https://admin.fedoraproject.org/mailman/listinfo/users
Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines