2009/12/14 Andrew Haley <aph@xxxxxxxxxx>
That looks alright.Adel ESSAFI wrote:
> Hi list
> This is the first time I have to configure linux as router.
> I have a single network card for which I gave to IPs
>
> eth0 Link encap:Ethernet HWaddr 00:11:5B:72:7F:D9
> inet addr:41.231.X.Y Bcast:41.255.255.255 Mask:255.255.255.0
> inet6 addr: fe80::211:5bff:fe72:7fd9/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:2595 errors:0 dropped:0 overruns:0 frame:0
> TX packets:2295 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:1876353 (1.7 MiB) TX bytes:328059 (320.3 KiB)
> Interrupt:21 Base address:0x8000
>
> eth0:1 Link encap:Ethernet HWaddr 00:11:5B:72:7F:D9
> inet addr:192.168.10.10 Bcast:192.168.10.255 Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> Interrupt:21 Base address:0x8000
>
>
>
>
> and this is the default route
>
> [root@routeur ~]# route
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use
> Iface
> 41.231.2.0 * 255.255.255.0 U 0 0 0 eth0
> 192.168.10.0 * 255.255.255.0 U 0 0 0 eth0
> link-local * 255.255.0.0 U 1002 0 0 eth0
> default 41.231.2.81 0.0.0.0 UG 0 0 0 eth0
>
This isn't making very much sense.
> The problem now, is when I configure a PC with an IP adress 192.168.10.X
> and I put the gateway as 192.168.10.10, I do not succeed to ping any PC. How
> can I route all the packages from eth0:1 to eth0??
What is the address of your gateway? If it is 41.231.2.81, then it makes no
sense to move it to the 192.168.10 network.
Well, I have no great experience with routing but I am in an internet café where I have a limited number of addresses.
so my logical configuration is as follows
ISP -- ROUTER 41.231.2.81 <--LAN--> 41.231.2.83 My SERVER 192.168.10.10 <--- LAN --> CLients 102.168.10.X
I hope with that figure things are more precise
Thanks for help
so my logical configuration is as follows
ISP -- ROUTER 41.231.2.81 <--LAN--> 41.231.2.83 My SERVER 192.168.10.10 <--- LAN --> CLients 102.168.10.X
I hope with that figure things are more precise
Thanks for help
If you're trying to set up a local network with NAT forwarding, then there's
more to do.
Andrew.
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
--
http://ilovefedora.blogspot.com/
--
PhD candidate in Computer Science
Address
BP 108, Bureau de poste Tunis republique
1001 Tunis
Tunisia
tel: +216 97 246 706
fax: +216 71 391 166
-- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
