On Sat, 2009-06-20 at 16:28 -0400, Kanwar Ranbir Sandhu wrote: > When I boot the machine, the card appears to be detected properly. But, > the actual RAID array isn't. That is, instead of seeing one drive, all > three drives are detected individually. Oh, the sata_mv module is being > automatically loaded. > Does anyone know what could be wrong? I should have included the output when the sata_mv module is loaded: Jun 20 15:58:37 ranbir kernel: sata_mv 0000:05:00.0: version 1.24 Jun 20 15:58:37 ranbir kernel: sata_mv 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jun 20 15:58:37 ranbir kernel: sata_mv 0000:05:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx Jun 20 15:58:37 ranbir kernel: scsi14 : sata_mv Jun 20 15:58:37 ranbir kernel: scsi15 : sata_mv Jun 20 15:58:37 ranbir kernel: scsi16 : sata_mv Jun 20 15:58:37 ranbir kernel: scsi17 : sata_mv Jun 20 15:58:37 ranbir kernel: ata13: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb22000 irq 16 Jun 20 15:58:37 ranbir kernel: ata14: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb24000 irq 16 Jun 20 15:58:37 ranbir kernel: ata15: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb26000 irq 16 Jun 20 15:58:37 ranbir kernel: ata16: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb28000 irq 16 Jun 20 15:58:37 ranbir kernel: ata13: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jun 20 15:58:38 ranbir kernel: ata13.00: ATA-7: ST3500630AS, 3.AAC, max UDMA/133 Jun 20 15:58:38 ranbir kernel: ata13.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) Jun 20 15:58:38 ranbir kernel: ata13.00: configured for UDMA/133 Jun 20 15:58:38 ranbir kernel: ata14: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jun 20 15:58:38 ranbir kernel: ata14.00: ATA-7: ST3500630AS, 3.AAC, max UDMA/133 Jun 20 15:58:38 ranbir kernel: ata14.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) Jun 20 15:58:38 ranbir kernel: ata14.00: configured for UDMA/133 Jun 20 15:58:39 ranbir kernel: ata15: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jun 20 15:58:39 ranbir kernel: ata15.00: ATA-8: ST3500320AS, SD15, max UDMA/133 Jun 20 15:58:39 ranbir kernel: ata15.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) Jun 20 15:58:39 ranbir kernel: ata15.00: configured for UDMA/133 Jun 20 15:58:39 ranbir kernel: ata16: SATA link down (SStatus 0 SControl 300) Jun 20 15:58:39 ranbir kernel: scsi 14:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 Jun 20 15:58:39 ranbir kernel: sd 14:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) Jun 20 15:58:39 ranbir kernel: sd 14:0:0:0: [sdc] Write Protect is off Jun 20 15:58:39 ranbir kernel: sd 14:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jun 20 15:58:39 ranbir kernel: sd 14:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) Jun 20 15:58:39 ranbir kernel: sd 14:0:0:0: [sdc] Write Protect is off Jun 20 15:58:39 ranbir kernel: sd 14:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jun 20 15:58:39 ranbir kernel: sdc: unknown partition table Jun 20 15:58:39 ranbir kernel: sd 14:0:0:0: [sdc] Attached SCSI disk Jun 20 15:58:39 ranbir kernel: sd 14:0:0:0: Attached scsi generic sg2 type 0 Jun 20 15:58:39 ranbir kernel: scsi 15:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 Jun 20 15:58:39 ranbir kernel: sd 15:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) Jun 20 15:58:39 ranbir kernel: sd 15:0:0:0: [sdd] Write Protect is off Jun 20 15:58:39 ranbir kernel: sd 15:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jun 20 15:58:39 ranbir kernel: sd 15:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) Jun 20 15:58:39 ranbir kernel: sd 15:0:0:0: [sdd] Write Protect is off Jun 20 15:58:39 ranbir kernel: sd 15:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jun 20 15:58:39 ranbir kernel: sdd: unknown partition table Jun 20 15:58:39 ranbir kernel: sd 15:0:0:0: [sdd] Attached SCSI disk Jun 20 15:58:39 ranbir kernel: sd 15:0:0:0: Attached scsi generic sg3 type 0 Jun 20 15:58:39 ranbir kernel: scsi 16:0:0:0: Direct-Access ATA ST3500320AS SD15 PQ: 0 ANSI: 5 Jun 20 15:58:39 ranbir kernel: sd 16:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB) Jun 20 15:58:39 ranbir kernel: sd 16:0:0:0: [sde] Write Protect is off Jun 20 15:58:39 ranbir kernel: sd 16:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jun 20 15:58:39 ranbir kernel: sd 16:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB) Jun 20 15:58:39 ranbir kernel: sd 16:0:0:0: [sde] Write Protect is off Jun 20 15:58:39 ranbir kernel: sd 16:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jun 20 15:58:39 ranbir kernel: sde: unknown partition table Jun 20 15:58:39 ranbir kernel: sd 16:0:0:0: [sde] Attached SCSI disk Jun 20 15:58:39 ranbir kernel: sd 16:0:0:0: Attached scsi generic sg4 type 0 -- Kanwar Ranbir Sandhu Linux 2.6.27.24-170.2.68.fc10.x86_64 x86_64 GNU/Linux 16:32:11 up 58 min, 4 users, load average: 0.00, 0.02, 0.06 -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
