|
wpa_supplicant -dd -c /etc/wpa_supplicant/wpa_supplicant.conf -ira0 -Dwext would work flawlessly on FC7 On F11, I get this: [root@localhost 2009_0521_RT2860_Linux_STA_V2.1.2.0]# wpa_supplicant -dd -c /etc/wpa_supplicant/wpa_ supplicant.conf -ira0 -Dwext Initializing interface 'ra0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' ctrl_interface='/var/run/wpa_supplicant' ctrl_interface_group='wheel' Initializing interface (2) 'ra0' Interface ra0 set UP - waiting a second for the driver to complete initialization SIOCGIWRANGE: WE(compiled)=22 WE(source)=14 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 WEXT: Operstate: linkmode=1, operstate=5 Own MAC address: 00:0C:7a:2b:cc:b7 wpa_driver_wext_set_wpa wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_countermeasures wpa_driver_wext_set_drop_unencrypted RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED Using existing control interface directory. ctrl_interface_group=10 (from group name 'wheel') Added interface ra0 RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) RTM_NEWLINK, IFLA_IFNAME: Interface 'ra0' added RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) RTM_NEWLINK, IFLA_IFNAME: Interface 'ra0' added Wireless event: cmd=0x8b06 len=8 RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) RTM_NEWLINK, IFLA_IFNAME: Interface 'ra0' added State: DISCONNECTED -> SCANNING Starting AP scan (broadcast SSID) Trying to get current scan results first without requesting a new scan to speed up initial association ioctl[SIOCGIWSCAN]: Resource temporarily unavailable Failed to get scan results Failed to get scan results - try scanning again Setting scan request: 0 sec 0 usec Starting AP scan (broadcast SSID) Scan requested (ret=0) - scan timeout 5 seconds EAPOL: disable timer tick Scan timeout - try to get results Received 996 bytes of scan results (8 BSSes) CTRL-EVENT-SCAN-RESULTS No suitable AP found. Setting scan request: 5 sec 0 usec No enabled networks - do not scan State: SCANNING -> INACTIVE The wpa supplicant completely stops scanning. I am puzzled why it works on FC7 butnot on F11 (same ra driver - albeit, recompiles for F11), and same wpa_supplicant.conf file. The wpa_supplicant.conf file contains: ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=wheel # ap_scan=1 ap_scan=2 network={ bssid=00:D5:C2:51:F3:C4 ssid="MyHiddenSSID" mode=MANAGED proto=WPA2 key_mgmt=WPA-PSK pairwise=TKIP group=TKIP scan_ssid=1 # only needed if your access point uses a hidden ssid psk="GoesWithoutSayingThatSomeThingsAreBetterLeftUnsaid" } I set scan_ssid=1 because my router does not broadcast the ssid. Windows Live™: Keep your life in sync. Check it out. |
-- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
