On Tue, 2009-05-05 at 23:33 +0200, Nigel Henry wrote: > On Tuesday 05 May 2009 00:55, William Case wrote: > > Thanks Nigel; > > > > On Mon, 2009-05-04 at 23:06 +0200, Nigel Henry wrote: > > > On Sunday 03 May 2009 20:04, William Case wrote: > > Hi Bill. > > Apologies. I forgot to add the alsamixer command so as to bypass the default > alsamixer screen when pulseaudio is installed. The command below will open > alsamixer and show all controls available for your soundcard. Again F4 will > show the capture controls. > > alsamixer -D hw:0 > > Your lsmod shows a bunch of modules loaded that are specific to the TV card. > Quite why the tuner module isn't being loaded automatically, I don't know. It > may be worth a look at dmesg, and see what is being loaded for the TV card. > You may see some reference to the tuner module. dmesg ... tveeprom 1-0050: Hauppauge model 78521, rev C1E9, serial# 4870798 tveeprom 1-0050: MAC address is 00-0D-FE-4A-52-8E tveeprom 1-0050: tuner model is Philips 18271_8295 (idx 149, type 54) tveeprom 1-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88) tveeprom 1-0050: audio processor is CX23887 (idx 42) tveeprom 1-0050: decoder processor is CX23887 (idx 37) tveeprom 1-0050: has radio cx23885[0]: hauppauge eeprom: model=78521 cx25840' 3-0044: cx25 0-21 found @ 0x88 (cx23885[0]) cx23885[0]/0: registered device video0 [v4l2] end_request: I/O error, dev sr0, sector 0 __ratelimit: 82 callbacks suppressed Buffer I/O error on device sr0, logical block 0 firmware: requesting v4l-cx23885-avcore-01.fw end_request: I/O error, dev sr0, sector 4 Buffer I/O error on device sr0, logical block 1 Buffer I/O error on device sr0, logical block 2 Buffer I/O error on device sr0, logical block 3 Buffer I/O error on device sr0, logical block 4 Buffer I/O error on device sr0, logical block 5 Buffer I/O error on device sr0, logical block 6 Buffer I/O error on device sr0, logical block 7 end_request: I/O error, dev sr0, sector 0 Buffer I/O error on device sr0, logical block 0 Buffer I/O error on device sr0, logical block 1 HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 HDA Intel 0000:00:1b.0: setting latency timer to 64 cx25840' 3-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes) cx23885[0]: registered device video1 [mpeg] cx23885[0]: cx23885 based dvb card MT2131: successfully identified at address 0x61 .... tuner' 1-0061: chip found @ 0xc2 (cx23885[0]) tuner' 2-0042: chip found @ 0x84 (cx23885[0]) tda829x 2-0042: could not clearly identify tuner address, defaulting to 60 tda18271 2-0060: creating new instance I have: /lib/firmware/v4l-cx23885-avcore-01.fw /lib/firmware/v4l-cx23885-enc.fw One site I googled suggests that they should be in /lib/firmware/your-kernel-version. I would think it depends on where the init looks. For Fedora 10, since there is no '/lib/firmware/your-kernel-version' directory it wouldn't be necessary. > > If you still can't get any sounds after fiddling with alsamixer, it may be > worth disabling pulseaudio temporarily, in case it for some reason is not > able to deal with sound output from the TV card. The command below as root > will disable it. > > yum remove alsa-plugins-pulseaudio > I will try that next but first I thought I would straighten out any problems in dmesg. -- Regards Bill Fedora 10, Gnome 2.24.3 Evo.2.24.5, Emacs 22.3.1 -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
