Greetings,
This evening when I installed my USB MicroSD reader into a USB port it
failed to be mounted.
My flash drives mount properly.
Looking at the log files I see:
Apr 21 23:12:54 brill kernel: usb 1-2: new high speed USB device using
ehci_hcd and address 7
Apr 21 23:12:54 brill kernel: usb 1-2: configuration #1 chosen from 1
choice
Apr 21 23:12:54 brill kernel: scsi11 : SCSI emulation for USB Mass Storage
devices
Apr 21 23:12:54 brill kernel: usb 1-2: New USB device found,
idVendor=090c, idProduct=6200
Apr 21 23:12:54 brill kernel: usb 1-2: New USB device strings: Mfr=1,
Product=2, SerialNumber=3
Apr 21 23:12:54 brill kernel: usb 1-2: Product: Generic USB2.0 card
Apr 21 23:12:54 brill kernel: usb 1-2: Manufacturer: Silicon Motion, Inc.
Apr 21 23:12:54 brill kernel: usb 1-2: SerialNumber: 12345678901234567890
Apr 21 23:12:59 brill kernel: scsi 11:0:0:0: Direct-Access Generic
USB SD Reader 1.00 PQ: 0 ANSI: 0 CCS
Apr 21 23:12:59 brill kernel: sd 11:0:0:0: [sdc] Attached SCSI removable
disk
Apr 21 23:12:59 brill kernel: sd 11:0:0:0: Attached scsi generic sg3 type
0
It stops there.
A few days ago when I mounted the reader and card, /var/log/messages read:
Apr 13 07:27:19 brill kernel: usb 3-1: USB disconnect, address 2
Apr 13 07:28:30 brill kernel: usb 1-1: new high speed USB device using
ehci_hcd and address 3
Apr 13 07:28:30 brill kernel: usb 1-1: configuration #1 chosen from 1
choice
Apr 13 07:28:30 brill kernel: usb 1-1: New USB device found,
idVendor=090c, idProduct=6200
Apr 13 07:28:30 brill kernel: usb 1-1: New USB device strings: Mfr=1,
Product=2, SerialNumber=3
Apr 13 07:28:30 brill kernel: usb 1-1: Product: Generic USB2.0 card
Apr 13 07:28:30 brill kernel: usb 1-1: Manufacturer: Silicon Motion, Inc.
Apr 13 07:28:30 brill kernel: usb 1-1: SerialNumber: 12345678901234567890
Apr 13 07:28:32 brill kernel: Initializing USB Mass Storage driver...
Apr 13 07:28:32 brill kernel: scsi6 : SCSI emulation for USB Mass Storage
devices
Apr 13 07:28:32 brill kernel: usbcore: registered new interface driver
usb-storage
Apr 13 07:28:32 brill kernel: USB Mass Storage support registered.
Apr 13 07:28:37 brill kernel: scsi 6:0:0:0: Direct-Access Generic USB
SD Reader 1.00 PQ: 0 ANSI: 0 CCS
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] 7745536 512-byte hardware
sectors (3966 MB)
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Write Protect is off
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Assuming drive cache:
write through
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] 7745536 512-byte hardware
sectors (3966 MB)
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Write Protect is off
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Assuming drive cache:
write through
Apr 13 07:28:37 brill kernel: sdc: sdc1
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Attached SCSI removable
disk
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: Attached scsi generic sg3 type 0
Apr 13 07:28:40 brill gnome-keyring-daemon[3199]: adding removable
location: volume_uuid_565F_311A at /media/Kingston
Apr 13 07:28:40 brill hald: mounted /dev/sdc1 on behalf of uid 500
Any suggestions on how to mount this card?
Much thanks.
Max Pyziur
pyz@xxxxxxxxx
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
