Re: Adaptec 29160 Ultra160 problem -- Fedora 9 install.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





--- On Tue, 9/30/08, gary artim <gartim@xxxxxxxxx> wrote:

> From: gary artim <gartim@xxxxxxxxx>
> Subject: Adaptec 29160 Ultra160 problem -- Fedora 9 install.
> To: fedora-list@xxxxxxxxxx
> Date: Tuesday, September 30, 2008, 12:49 AM
> Hi --
> 
> Installed fc9 on a server from fc8 and had a scsi
> controller Adaptec
> 29160 Ultra160 SCSI adapter
> give me grief. It's used with an lto autochanger. When
> I entered:
> 
> mtx -d /dev/changer status
> (/dev/changer a symlink to /dev/sg6)
> 
> It hung for a while, (a huge listing follows, sorry about
> this), then
> kernel messages gallor.
> 
> Anyway I tried  reseating the card, moving the card to an
> alternate
> slot, checking the cabling, reboot the autochanger,
> reboot the system  --all did _not_ help.
> 
> I pulled the card and replaced it with a Adaptec AIC-7892A
> U160/m (rev
> 02)  and the autochanger and lto drive worked.
> I also had to swap cables because of the interface
> differences.
> 
> Long story, but can anyone say that this card looks broken?
> It has a 5
> year warranty and would like to get it replaced if so. Or
> is
> it a driver issue/I couldn't find a direct hit
> searching the web or in
> the archives?
> 
> I think my head is still sore from banging it against the
> autochanger!
> Thanks for _any_ help!
> 
> -- Gary
> 
> Sep 27 10:30:15 genepi1 kernel: scsi5 : Adaptec AIC79XX
> PCI-X SCSI HBA
> DRIVER, Rev 3.0
> Sep 27 10:30:15 genepi1 kernel:        <Adaptec 29320ALP
> PCIx Ultra320
> SCSI adapter>
> Sep 27 10:30:15 genepi1 kernel:        aic7901: Ultra320
> Wide Channel
> A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
> Sep 27 10:30:15 genepi1 kernel: ACPI: PCI Interrupt
> 0000:04:01.0[A] ->
> GSI 16 (level, low) -> IRQ 16
> Sep 27 10:30:15 genepi1 kernel: e1000: 0000:04:01.0:
> e1000_probe:
> (PCI:66MHz:32-bit) 00:0e:0c:d9:8d:54
> Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0:
> Sequential-Access HP
>   Ultrium 4-SCSI   B12H PQ: 0 ANSI: 5
> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1:
> asynchronous
> Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:0: Tagged Queuing
> enabled.  Depth 4
> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Beginning
> Domain Validation
> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: wide
> asynchronous
> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: FAST-160
> WIDE SCSI
> 320.0 MB/s DT IU RTI PCOMP (6.25 ns, offset 64)
> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Domain
> Validation
> skipping write tests
> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Ending
> Domain Validation
> Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Medium
> Changer
> OVERLAND NEO Series       0504 PQ: 0 ANSI: 5
> Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:1: Tagged Queuing
> enabled.  Depth 4
> Sep 27 10:30:15 genepi1 kernel: e1000: eth2: e1000_probe:
> Intel(R)
> PRO/1000 Network Connection
> Sep 27 10:30:15 genepi1 kernel: device-mapper: uevent:
> version 1.0.3
> Sep 27 10:30:15 genepi1 kernel: device-mapper: ioctl:
> 4.13.0-ioctl
> (2007-10-18) initialised: dm-devel@xxxxxxxxxx
> Sep 27 10:30:15 genepi1 kernel: device-mapper: multipath:
> version 1.0.5 loaded
> Sep 27 10:30:15 genepi1 kernel: EXT3 FS on sda1, internal
> journal
> Sep 27 10:30:15 genepi1 kernel: Adding 25165812k swap on
> /dev/sda2.
> Priority:-1 extents:1 across:25165812k
> Sep 27 10:30:15 genepi1 kernel: firmware: requesting
> intel-ucode/06-0f-06
> Sep 27 10:30:15 genepi1 kernel: firmware: requesting
> intel-ucode/06-0f-06
> Sep 27 10:30:15 genepi1 kernel: firmware: requesting
> intel-ucode/06-0f-06
> Sep 27 10:30:15 genepi1 kernel: firmware: requesting
> intel-ucode/06-0f-06
> Sep 27 10:30:15 genepi1 kernel: IA-32 Microcode Update
> Driver: v1.14a
> <tigran@xxxxxxxxxxxxxxxxxxxx>
> Sep 27 10:30:15 genepi1 kernel: microcode: CPU0 updated
> from revision
> 0x44 to 0xcd, date = 09162007
> Sep 27 10:30:15 genepi1 kernel: microcode: CPU1 updated
> from revision
> 0x44 to 0xcd, date = 09162007
> Sep 27 10:30:15 genepi1 kernel: microcode: CPU2 updated
> from revision
> 0x44 to 0xcd, date = 09162007
> Sep 27 10:30:15 genepi1 kernel: microcode: CPU3 updated
> from revision
> 0x44 to 0xcd, date = 09162007
> Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0: Attached scsi
> generic sg5 type 1
> Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Attached scsi
> generic sg6 type 8
> Sep 27 10:30:15 genepi1 kernel: osst :I: Tape driver with
> OnStream
> support version 0.99.4
> Sep 27 10:30:15 genepi1 kernel: osst :I: $Id: osst.c,v 1.73
> 2005/01/01
> 21:13:34 wriede Exp $
> Sep 27 10:30:15 genepi1 kernel: Driver 'osst' needs
> updating - please
> use bus_type methods
> Sep 27 10:30:15 genepi1 kernel: st: Version 20080224, fixed
> bufsize
> 32768, s/g segs 256
> Sep 27 10:30:15 genepi1 kernel: Driver 'st' needs
> updating - please
> use bus_type methods
> Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: Attached scsi
> tape st0
> Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: st0: try direct
> i/o: yes
> (alignment 4 B)
> Sep 27 10:30:15 genepi1 kernel: eth0: Link is Up 1000 Mbps
> Full
> Duplex, Flow Control: RX
> Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_CHANGE):
> eth0: link
> becomes ready
> Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_UP): eth1:
> link is not ready
> Sep 27 10:54:58 genepi1 yum: Installed:
> mtx-1.3.12-1.fc9.x86_64
> Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x010D):
> Invalid field in CDB:.
> Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x0101):
> Invalid command opcode:opcode=0xB8.
> Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x0101):
> Invalid command opcode:opcode=0xB8.
> Sep 27 11:02:27 genepi1 kernel: st 5:0:1:0: Attempting to
> queue an
> ABORT message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
> Sep 27 11:02:27 genepi1 kernel: scsi5: At time of recovery,
> card was not paused
> Sep 27 11:02:27 genepi1 kernel:
> >>>>>>>>>>>>>>>>>>
> Dump Card State
> Begins
> <<<<<<<<<<<<<<<<<
> Sep 27 11:02:27 genepi1 kernel: scsi5: Dumping Card State
> at program
> address 0x34 Mode 0x22
> Sep 27 11:02:27 genepi1 kernel: Card was paused
> Sep 27 11:02:27 genepi1Sep 27 11:02:27 genepi1 kernel:
> INTSTAT[0x0]
> SELOID[0x1] SELID[0x10] HS_MAILBOX[0x0]
> Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80]
> SEQINTSTAT[0x0]
> SAVED_MODE[0x11] DFFSTAT[0x33]
> Sep 27 11:02:27 genepi1 kernel: SCSISIGI[0x0]
> SCSIPHASE[0x0]
> SCSIBUS[0x0] LASTPHASE[0x1]
> Sep 27 11:02:27 genepi1 kernel: SCSISEQ0[0x0]
> SCSISEQ1[0x12]
> SEQCTL0[0x0] SEQINTCTL[0x0]
> Sep 27 11:02:27 genepi1 kernel: SEQ_FLAGS[0x0]
> SEQ_FLAGS2[0x4]
> QFREEZE_COUNT[0x7]
> Sep 27 11:02:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
> MK_MESSAGE_SCB[0xff00]
> Sep 27 11:02:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
> SSTAT0[0x0] SSTAT1[0x8]
> Sep 27 11:02:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
> PERRDIAG[0x0]
> SIMODE1[0xa4]
> Sep 27 11:02:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
> LQISTAT2[0x0] LQOSTAT0[0x0]
> Sep 27 11:02:27 genepi1 kernel: LQOSTAT1[0x0]
> LQOSTAT2[0xe1]
> Sep 27 11:02:27 genepi1 kernel:
> Sep 27 11:02:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING
> = 0 LASTSCB
> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
> Sep 27 11:02:27 genepi1 kernel: qinstart = 44 qinfifonext =
> 46
> Sep 27 11:02:27 genepi1 kernel: QINFIFO: 0x3 0x2
> Sep 27 11:02:27 genepi1 kernel: WAITING_TID_QUEUES:
> Sep 27 11:02:27 genepi1 kernel: Pending list:
> Sep 27 11:02:27 genepi1 kernel:  2 FIFO_USE[0x0]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:02:27 genepi1 kernel:  3 FIFO_USE[0x2]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:02:27 genepi1 kernel: Total 2
> Sep 27 11:02:27 genepi1 kernel: Kernel Free SCB list: 1 0
> Sep 27 11:02:27 genepi1 kernel: Sequencer Complete
> DMA-inprog list:
> Sep 27 11:02:27 genepi1 kernel: Sequencer Complete list:
> Sep 27 11:02:27 genepi1 kernel: Sequencer DMA-Up and
> Complete list:
> Sep 27 11:02:27 genepi1 kernel: Sequencer On QFreeze and
> Complete list:
> Sep 27 11:02:27 genepi1 kernel:
> Sep 27 11:02:27 genepi1 kernel:
> Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
> == 0x82a3, SCB 0x3
> Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:27 genepi1 kernel:
> Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
> == 0x8063, SCB 0x3
> Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
> 0x1 0x0 0x0
> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:02:27 genepi1 kernel: scsi5: LQISTATE = 0x0,
> LQOSTATE = 0x0,
> OPTIONMODE = 0x52
> Sep 27 11:02:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
> MAXCMDCNT = 0x1
> Sep 27 11:02:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
> SAVED_LUN = 0x0
> Sep 27 11:02:27 genepi1 kernel: SIMODE0[0xc]
> Sep 27 11:02:27 genepi1 kernel: CCSCBCTL[0x0]
> Sep 27 11:02:27 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
> = 0x104,
> DINDEX = 0x104
> Sep 27 11:02:27 genepi1 kernel: scsi5: SCBPTR == 0x3,
> SCB_NEXT ==
> 0xff80, SCB_NEXT2 == 0xff80
> Sep 27 11:02:27 genepi1 kernel: CDB 3 0 0 83 a 8c
> Sep 27 11:02:27 genepi1 kernel: STACK: 0x20 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0
> Sep 27 11:02:27 genepi1 kernel:
> <<<<<<<<<<<<<<<<<
> Dump Card State Ends
> >>>>>>>>>>>>>>>>>>
> Sep 27 11:02:27 genepi1 kernel: scsi5:0:1:0: Cmd aborted
> from QINFIFO
> Sep 27 11:02:37 genepi1 kernel: st 5:0:1:0: Attempting to
> queue an
> ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
> card was not paused
> Sep 27 11:02:37 genepi1 kernel:
> >>>>>>>>>>>>>>>>>>
> Dump Card State
> Begins
> <<<<<<<<<<<<<<<<<
> Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
> at program
> address 0x18 Mode 0x33
>  kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
> HS_MAILBOX[0x0]
> Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80]
> SEQINTSTAT[0x0]
> SAVED_MODE[0x11] DFFSTAT[0x33]
> Sep 27 11:02:37 genepi1 kernel:
> >>>>>>>>>>>>>>>>>>
> Dump Card State
> Begins
> <<<<<<<<<<<<<<<<<
> Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
> at program
> address 0x18 Mode 0x33
> Sep 27 11:02:37 genepi1 kernel: Card was paused
> Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
> SELID[0x10]
> HS_MAILBOX[0x0]
> Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
> SEQINTSTAT[0x0]
> SAVED_MODE[0x11] DFFSTAT[0x33]
> Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
> SCSIPHASE[0x0]
> SCSIBUS[0x0] LASTPHASE[0x1]
> Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
> SCSISEQ1[0x12]
> SEQCTL0[0x0] SEQINTCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
> SEQ_FLAGS2[0x4]
> QFREEZE_COUNT[0x7]
> Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
> MK_MESSAGE_SCB[0xff00]
> Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
> SSTAT0[0x0] SSTAT1[0x0]
> Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
> PERRDIAG[0x0]
> SIMODE1[0xa4]
> Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
> LQISTAT2[0x0] LQOSTAT0[0x0]
> Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
> LQOSTAT2[0xe1]
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
> = 0 LASTSCB
> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
> Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
> 46
> Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3 0x2
> Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
> Sep 27 11:02:37 genepi1 kernel: Pending list:
> Sep 27 11:02:37 genepi1 kernel:  2 FIFO_USE[0x0]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:02:37 genepi1 kernel:  3 FIFO_USE[0x2]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:02:37 genepi1 kernel: Total 2
> Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 1 0
> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
> DMA-inprog list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
> Complete list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
> Complete list:
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
> == 0x82a3, SCB 0x3
> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
> == 0x8063, SCB 0x3
> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
> 0x1 0x0 0x0
> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
> LQOSTATE = 0x0,
> OPTIONMODE = 0x52
> Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
> MAXCMDCNT = 0x1
> Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
> SAVED_LUN = 0x0
> Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
> Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0xffff,
> SINDEX = 0x104,
> DINDEX = 0x104
> Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
> SCB_NEXT ==
> 0xff80, SCB_NEXT2 == 0xff80
> Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
> Sep 27 11:02:37 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0
> Sep 27 11:02:37 Sep 27 11:02:37 genepi1 kernel:
> scsi5:0:1:0: Cmd
> aborted from QINFIFO
> Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
> queue an
> ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
> Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
> card was not paused
> Sep 27 11:02:37 genepi1 kernel:
> >>>>>>>>>>>>>>>>>>
> Dump Card State
> Begins
> <<<<<<<<<<<<<<<<<
> Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
> at program
> address 0x31 Mode 0x11
> Sep 27 11:02:37 genepi1 kernel: Card was paused
> Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
> SELID[0x10]
> HS_MAILBOX[0x0]
> Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
> SEQINTSTAT[0x0]
> SAVED_MODE[0x11] DFFSTAT[0x33]
> Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
> SCSIPHASE[0x0]
> SCSIBUS[0x0] LASTPHASE[0x1]
> Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
> SCSISEQ1[0x12]
> SEQCTL0[0x0] SEQINTCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
> SEQ_FLAGS2[0x4]
> QFREEZE_COUNT[0x7]
> Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
> MK_MESSAGE_SCB[0xff00]
> Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
> SSTAT0[0x0] SSTAT1[0x0]
> Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
> PERRDIAG[0x0]
> SIMODE1[0xa4]
> Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
> LQISTAT2[0x0] LQOSTAT0[0x0]
> Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
> LQOSTAT2[0xe1]
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
> = 0 LASTSCB
> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
> Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
> 45
> Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
> Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
> Sep 27 11:02:37 genepi1 kernel: Pending list:
> Sep 27 11:02:37 genepi1 kernel:  3 FIFO_USE[0x0]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:02:37 genepi1 kernel: Total 1
> Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
> DMA-inprog list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
> Complete list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
> Complete list:
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
> == 0x82a3, SCB 0x3
> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
> == 0x8063, SCB 0x3
> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
> 0x1 0x0 0x0
> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
> LQOSTATE = 0x0,
> OPTIONMODE = 0x52
> Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
> MAXCMDCNT = 0x1
> Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
> SAVED_LUN = 0x0
> Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
> Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
> = 0x104,
> DINDEX = 0x104
> Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
> SCB_NEXT ==
> 0xff80, SCB_NEXT2 == 0xff80
> Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
> Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0
> Sep 27 11:02:37 genepi1 kernel:
> <<<<<<<<<<<<<<<<<
> Dump Card State Ends
> >>>>>>>>>>>>>>>>>>
> genepi1 kernel:
> <<<<<<<<<<<<<<<<<
> Dump Card State Ends
> >>>>>>>>>>>>>>>>>>
> Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted
> from QINFIFO
> Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
> queue an
> ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
> Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted
> from QINFIFO
> Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
> queue an
> ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
> Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
> card was not paused
> Sep 27 11:02:37 genepi1 kernel:
> >>>>>>>>>>>>>>>>>>
> Dump Card State
> Begins
> <<<<<<<<<<<<<<<<<
> Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
> at program
> address 0x31 Mode 0x11
> Sep 27 11:02:37 genepi1 kernel: Card was paused
> Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
> SELID[0x10]
> HS_MAILBOX[0x0]
> Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
> SEQINTSTAT[0x0]
> SAVED_MODE[0x11] DFFSTAT[0x33]
> Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
> SCSIPHASE[0x0]
> SCSIBUS[0x0] LASTPHASE[0x1]
> Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
> SCSISEQ1[0x12]
> SEQCTL0[0x0] SEQINTCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
> SEQ_FLAGS2[0x4]
> QFREEZE_COUNT[0x7]
> Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
> MK_MESSAGE_SCB[0xff00]
> Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
> SSTAT0[0x0] SSTAT1[0x0]
> Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
> PERRDIAG[0x0]
> SIMODE1[0xa4]
> Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
> LQISTAT2[0x0] LQOSTAT0[0x0]
> Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
> LQOSTAT2[0xe1]
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
> = 0 LASTSCB
> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
> Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
> 45
> Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
> Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
> Sep 27 11:02:37 genepi1 kernel: Pending list:
> Sep 27 11:02:37 genepi1 kernel:  3 FIFO_USE[0x0]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:02:37 genepi1 kernel: Total 1
> Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
> DMA-inprog list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
> Complete list:
> Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
> Complete list:
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
> == 0x82a3, SCB 0x3
> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:37 genepi1 kernel:
> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
> == 0x8063, SCB 0x3
> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
> 0x1 0x0 0x0
> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
> LQOSTATE = 0x0,
> OPTIONMODE = 0x52
> Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
> MAXCMDCNT = 0x1
> Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
> SAVED_LUN = 0x0
> Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
> Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
> Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
> = 0x104,
> DINDEX = 0x104
> Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
> SCB_NEXT ==
> 0xff80, SCB_NEXT2 == 0xff80
> Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
> Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0
> Sep 27 11:02:37 genepi1 kernel:
> <<<<<<<<<<<<<<<<<
> Dump Card State Ends
> >>>>>>>>>>>>>>>>>>
> Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0
> Sep 27 11:02:37 genepi1 kernel:
> <<<<<<<<<<<<<<<<<
> Dump Card State Ends
> >>>>>>>>>>>>>>>>>>
> Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:1: Cmd aborted
> from QINFIFO
> Sep 27 11:02:47 genepi1 kernel: scsi 5:0:1:1: Attempting to
> queue an
> ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:02:47 genepi1 kernel: scsi5: At time of recovery,
> card was not paused
> Sep 27 11:02:47 genepi1 kernel:
> >>>>>>>>>>>>>>>>>>
> Dump Card State
> Begins
> <<<<<<<<<<<<<<<<<
> Sep 27 11:02:47 genepi1 kernel: scsi5: Dumping Card State
> at program
> address 0x18 Mode 0x33
> Sep 27 11:02:47 genepi1 kernel: Card was paused
> Sep 27 11:02:47 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
> SELID[0x10]
> HS_MAILBOX[0x0]
> Sep 27 11:02:47 genepi1 kernel: INTCTL[0x80]
> SEQINTSTAT[0x0]
> SAVED_MODE[0x11] DFFSTAT[0x33]
> Sep 27 11:02:47 genepi1 kernel: SCSISIGI[0x0]
> SCSIPHASE[0x0]
> SCSIBUS[0x0] LASTPHASE[0x1]
> Sep 27 11:02:47 genepi1 kernel: SCSISEQ0[0x0]
> SCSISEQ1[0x12]
> SEQCTL0[0x0] SEQINTCTL[0x0]
> Sep 27 11:02:47 genepi1 kernel: SEQ_FLAGS[0x0]
> SEQ_FLAGS2[0x4]
> QFREEZE_COUNT[0x7]
> Sep 27 11:02:47 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
> MK_MESSAGE_SCB[0xff00]
> Sep 27 11:02:47 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
> SSTAT0[0x0] SSTAT1[0x0]
> Sep 27 11:02:47 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
> PERRDIAG[0x0]
> SIMODE1[0xa4]
> Sep 27 11:02:47 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
> LQISTAT2[0x0] LQOSTAT0[0x0]
> Sep 27 11:02:47 genepi1 kernel: LQOSTAT1[0x0]
> LQOSTAT2[0xe1]
> Sep 27 11:02:47 genepi1 kernel:
> Sep 27 11:02:47 genepi1 kernel: SCB Count = 4 CMDS_PENDING
> = 0 LASTSCB
> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
> Sep 27 11:02:47 genepi1 kernel: qinstart = 44 qinfifonext =
> 45
> Sep 27 11:02:47 genepi1 kernel: QINFIFO: 0x3
> Sep 27 11:02:47 genepi1 kernel: WAITING_TID_QUEUES:
> Sep 27 11:02:47 genepi1 kernel: Pending list:
> Sep 27 11:02:47 genepi1 kernel:  3 FIFO_USE[0x0]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:02:47 genepi1 kernel: Total 1
> Sep 27 11:02:47 genepi1 kernel: Kernel Free SCB list: 2 1 0
> Sep 27 11:02:47 genepi1 kernel: Sequencer Complete
> DMA-inprog list:
> Sep 27 11:02:47 genepi1 kernel: Sequencer Complete list:
> Sep 27 11:02:47 genepi1 kernel: Sequencer DMA-Up and
> Complete list:
> Sep 27 11:02:47 genepi1 kernel: Sequencer On QFreeze and
> Complete list:
> Sep 27 11:02:47 genepi1 kernel:
> Sep 27 11:02:47 genepi1 kernel:
> Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
> == 0x82a3, SCB 0x3
> Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:47 genepi1 kernel:
> Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
> == 0x8063, SCB 0x3
> Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:02:47 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
> 0x1 0x0 0x0
> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:02:47 genepi1 kernel: scsi5: LQISTATE = 0x0,
> LQOSTATE = 0x0,
> OPTIONMODE = 0x52
> Sep 27 11:02:47 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
> MAXCMDCNT = 0x1
> Sep 27 11:02:47 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
> SAVED_LUN = 0x0
> Sep 27 11:02:47 genepi1 kernel: SIMODE0[0xc]
> Sep 27 11:02:47 genepi1 kernel: CCSCBCTL[0x0]
> Sep 27 11:02:47 genepi1 kernel: scsi5: REG0 == 0xffff,
> SINDEX = 0x104,
> DINDEX = 0x104
> Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3,
> SCB_NEXT ==
> 0xff80, SCB_NEXT2 == 0xff80
> Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
> Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3,
> SCB_NEXT ==
> 0xff80, SCB_NEXT2 == 0xff80
> Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
> Sep 27 11:02:47 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0
> Sep 27 11:02:47 genepi1 kernel:
> <<<<<<<<<<<<<<<<<
> Dump Card State Ends
> >>>>>>>>>>>>>>>>>>
> Sep 27 11:02:47 genepi1 kernel: scsi5:0:1:1: Cmd aborted
> from QINFIFO
> Sep 27 11:02:47 genepi1 kernel: st 5:0:1:0: Attempting to
> queue a
> TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
> Sep 27 11:02:47 genepi1 kernel: scsi5: Device reset code
> sleeping
> Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset timer
> expired (active 1)
> Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset
> returning 0x2003
> Sep 27 11:02:52 genepi1 kernel: scsi 5:0:1:1: Attempting to
> queue a
> TARGET RESET message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
> Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset code
> sleeping
> Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset timer
> expired (active 1)
> Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset
> returning 0x2003
> Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
> Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
> Sep 27 11:03:17 genepi1 kernel: st 5:0:1:0: Attempting to
> queue an
> ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:03:17 genepi1 kernel: scsi5: At time of recovery,
> card was not paused
> Sep 27 11:03:17 genepi1 kernel:
> >>>>>>>>>>>>>>>>>>
> Dump Card State
> Begins
> <<<<<<<<<<<<<<<<<
> Sep 27 11:03:17 genepi1 kernel: scsi5: Dumping Card State
> at program
> address 0x9 Mode 0x33
> Sep 27 11:03:17 genepi1 kernel: Card was paused
> Sep 27 11:03:17 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
> SELID[0x10]
> HS_MAILBOX[0x0]
> Sep 27 11:03:17 genepi1 kernel: INTCTL[0x80]
> SEQINTSTAT[0x0]
> SAVED_MODE[0x11] DFFSTAT[0x33]
> Sep 27 11:03:17 genepi1 kernel: SCSISIGI[0x0]
> SCSIPHASE[0x0]
> SCSIBUS[0x0] LASTPHASE[0x1]
> Sep 27 11:03:17 genepi1 kernel: SCSISEQ0[0x0]
> SCSISEQ1[0x12]
> SEQCTL0[0x0] SEQINTCTL[0x0]
> Sep 27 11:03:17 genepi1 kernel: SEQ_FLAGS[0x0]
> SEQ_FLAGS2[0x4]
> QFREEZE_COUNT[0x7]
> Sep 27 11:03:17 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
> MK_MESSAGE_SCB[0xff00]
> Sep 27 11:03:17 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
> SSTAT0[0x0] SSTAT1[0x0]
> Sep 27 11:03:17 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
> PERRDIAG[0x0]
> SIMODE1[0xa4]
> Sep 27 11:03:17 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
> LQISTAT2[0x0] LQOSTAT0[0x0]
> Sep 27 11:03:17 genepi1 kernel: LQOSTAT1[0x0]
> LQOSTAT2[0xe1]
> Sep 27 11:03:17 genepi1 kernel:
> Sep 27 11:03:17 genepi1 kernel: SCB Count = 4 CMDS_PENDING
> = 0 LASTSCB
> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
> Sep 27 11:03:17 genepi1 kernel: qinstart = 44 qinfifonext =
> 45
> Sep 27 11:03:17 genepi1 kernel: QINFIFO: 0x2
> Sep 27 11:03:17 genepi1 kernel: WAITING_TID_QUEUES:
> Sep 27 11:03:17 genepi1 kernel: Pending list:
> Sep 27 11:03:17 genepi1 kernel:  2 FIFO_USE[0x0]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:03:17 genepi1 kernel: Total 1
> Sep 27 11:03:17 genepi1 kernel: Kernel Free SCB list: 3 1 0
> Sep 27 11:03:17 genepi1 kernel: Sequencer Complete
> DMA-inprog list:
> Sep 27 11:03:17 genepi1 kernel: Sequencer Complete list:
> Sep 27 11:03:17 genepi1 kernel: Sequencer DMA-Up and
> Complete list:
> Sep 27 11:03:17 genepi1 kernel: Sequencer On QFreeze and
> Complete list:
> Sep 27 11:03:17 genepi1 kernel:
> Sep 27 11:03:17 genepi1 kernel:
> Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
> == 0x80a3, SCB 0x3
> Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:03:17 genepi1 kernel:
> Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
> == 0x8063, SCB 0x3
> Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
> == 0x8063, SCB 0x3
> Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:03:17 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
> 0x1 0x0 0x0
> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:03:17 genepi1 kernel: scsi5: LQISTATE = 0x0,
> LQOSTATE = 0x0,
> OPTIONMODE = 0x52
> Sep 27 11:03:17 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
> MAXCMDCNT = 0x1
> Sep 27 11:03:17 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
> SAVED_LUN = 0x0
> Sep 27 11:03:17 genepi1 kernel: SIMODE0[0xc]
> Sep 27 11:03:17 genepi1 kernel: CCSCBCTL[0x0]
> Sep 27 11:03:17 genepi1 kernel: scsi5: REG0 == 0xffff,
> SINDEX = 0x104,
> DINDEX = 0x104
> Sep 27 11:03:17 genepi1 kernel: scsi5: SCBPTR == 0x3,
> SCB_NEXT ==
> 0xff80, SCB_NEXT2 == 0xff80
> Sep 27 11:03:17 genepi1 kernel: CDB 3 0 0 83 a 8c
> Sep 27 11:03:17 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0
> Sep 27 11:03:17 genepi1 kernel:
> <<<<<<<<<<<<<<<<<
> Dump Card State Ends
> >>>>>>>>>>>>>>>>>>
> Sep 27 11:03:17 genepi1 kernel: scsi5:0:1:0: Cmd aborted
> from QINFIFO
> Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Attempting to
> queue an
> ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:03:27 genepi1 kernel: scsi5: At time of recovery,
> card was not paused
> Sep 27 11:03:27 genepi1 kernel:
> >>>>>>>>>>>>>>>>>>
> Dump Card State
> Begins
> <<<<<<<<<<<<<<<<<
> Sep 27 11:03:27 genepi1 kernel: scsi5: Dumping Card State
> at program
> address 0x22 Mode 0x33
> Sep 27 11:03:27 genepi1 kernel: Card was paused
> Sep 27 11:03:27 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
> SELID[0x10]
> HS_MAILBOX[0x0]
> Sep 27 11:03:27 genepi1 kernel: INTCTL[0x80]
> SEQINTSTAT[0x0]
> SAVED_MODE[0x11] DFFSTAT[0x33]
> Sep 27 11:03:27 genepi1 kernel: SCSISIGI[0x0]
> SCSIPHASE[0x0]
> SCSIBUS[0x0] LASTPHASE[0x1]
> Sep 27 11:03:27 genepi1 kernel: SCSISEQ0[0x0]
> SCSISEQ1[0x12]
> SEQCTL0[0x0] SEQINTCTL[0x0]
> Sep 27 11:03:27 genepi1 kernel: SEQ_FLAGS[0x0]
> SEQ_FLAGS2[0x4]
> QFREEZE_COUNT[0x7]
> Sep 27 11:03:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
> MK_MESSAGE_SCB[0xff00]
> Sep 27 11:03:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
> SSTAT0[0x0] SSTAT1[0x0]
> Sep 27 11:03:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
> PERRDIAG[0x0]
> SIMODE1[0xa4]
> Sep 27 11:03:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
> LQISTAT2[0x0] LQOSTAT0[0x0]
> Sep 27 11:03:27 genepi1 kernel: LQOSTAT1[0x0]
> LQOSTAT2[0xe1]
> Sep 27 11:03:27 genepi1 kernel:
> Sep 27 11:03:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING
> = 0 LASTSCB
> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
> Sep 27 11:03:27 genepi1 kernel: qinstart = 44 qinfifonext =
> 45
> Sep 27 11:03:27 genepi1 kernel: QINFIFO: 0x2
> Sep 27 11:03:27 genepi1 kernel: WAITING_TID_QUEUES:
> Sep 27 11:03:27 genepi1 kernel: Pending list:
> Sep 27 11:03:27 genepi1 kernel:  2 FIFO_USE[0x0]
> SCB_CONTROL[0x68]
> SCB_SCSIID[0x17]
> Sep 27 11:03:27 genepi1 kernel: Total 1
> Sep 27 11:03:27 genepi1 kernel: Kernel Free SCB list: 3 1 0
> Sep 27 11:03:27 genepi1 kernel: Sequencer Complete
> DMA-inprog list:
> Sep 27 11:03:27 genepi1 kernel: Sequencer Complete list:
> Sep 27 11:03:27 genepi1 kernel: Sequencer DMA-Up and
> Complete list:
> Sep 27 11:03:27 genepi1 kernel: Sequencer On QFreeze and
> Complete list:
> Sep 27 11:03:27 genepi1 kernel:
> Sep 27 11:03:27 genepi1 kernel:
> Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
> == 0x80a3, SCB 0x3
> Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:03:Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00,
> HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:03:27 genepi1 kernel:
> Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
> == 0x8063, SCB 0x3
> Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f]
> SEQINTSRC[0x0]
> DFCNTRL[0x0] DFSTATUS[0x89]
> Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
> SG_STATE[0x0]
> DFFSXFRCTL[0x0]
> Sep 27 11:03:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
> SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:03:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
> 0x1 0x0 0x0
> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> Sep 27 11:03:27 genepi1 kernel: scsi5: LQISTATE = 0x0,
> LQOSTATE = 0x0,
> OPTIONMODE = 0x52
> Sep 27 11:03:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
> MAXCMDCNT = 0x1
> Sep 27 11:03:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
> SAVED_LUN = 0x0
> Sep 27 11:03:27 genepi1 kernel: SIMODE0[0xc]
> Sep 27 11:03:27 genepi1 kernel: CCSCBCTL[0x0]
> Sep 27 11:03:27 genepi1 kernel: scsi5: REG0 == 0xffff,
> SINDEX = 0x104,
> DINDEX = 0x104
> Sep 27 11:03:27 genepi1 kernel: scsi5: SCBPTR == 0x3,
> SCB_NEXT ==
> 0xff80, SCB_NEXT2 == 0xff80
> Sep 27 11:03:27 genepi1 kernel: CDB 3 0 0 83 a 8c
> Sep 27 11:03:27 genepi1 kernel: STACK: 0x1e 0x0 0x0 0x0 0x0
> 0x0 0x0 0x0
> Sep 27 11:03:27 genepi1 kernel:
> <<<<<<<<<<<<<<<<<
> Dump Card State Ends
> >>>>>>>>>>>>>>>>>>
> Sep 27 11:03:27 genepi1 kernel: scsi5:0:1:1: Cmd aborted
> from QINFIFO
> Sep 27 11:03:27 genepi1 kernel: st 5:0:1:0: Device offlined
> - not
> ready after error recovery
> Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Device
> offlined - not
> ready after error recovery
> Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x010D):
> Invalid field in CDB:.
> Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x0101):
> Invalid command opcode:opcode=0xB8.
> Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x0101):
> Invalid command opcode:opcode=0xB8.
> Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x010D):
> Invalid field in CDB:.
> Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x0101):
> Invalid command opcode:opcode=0xB8.
> Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x0101):
> Invalid command opcode:opcode=0xB8.
> Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x010D):
> Invalid field in CDB:.
> Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x0101):
> Invalid command opcode:opcode=0xB8.
> Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
> (0x03:0x0101):
> Invalid command opcode:opcode=0xB8.
> 27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
> 0x00, SHCNT = 0x0
> Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
> CCSGCTL[0x10]
> Sep 27 11:03:27 genepi1 kernel:
> 
My Adaptec 29160 Ultra160 comes with testing software shown early in boot!

Next comes grub
> -- 
> fedora-list mailing list
> fedora-list@xxxxxxxxxx
> To unsubscribe:
> https://www.redhat.com/mailman/listinfo/fedora-list
> Guidelines:
> http://fedoraproject.org/wiki/Communicate/MailingListGuidelines


      

-- 
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
[Index of Archives]     [Older Fedora Users]     [Fedora Announce]     [Fedora Package Announce]     [EPEL Announce]     [Fedora Magazine]     [Fedora News]     [Fedora Summer Coding]     [Fedora Laptop]     [Fedora Cloud]     [Fedora Advisory Board]     [Fedora Education]     [Fedora Security]     [Fedora Scitech]     [Fedora Robotics]     [Fedora Maintainers]     [Fedora Infrastructure]     [Fedora Websites]     [Anaconda Devel]     [Fedora Devel Java]     [Fedora Legacy]     [Fedora Desktop]     [Fedora Fonts]     [ATA RAID]     [Fedora Marketing]     [Fedora Management Tools]     [Fedora Mentors]     [SSH]     [Fedora Package Review]     [Fedora R Devel]     [Fedora PHP Devel]     [Kickstart]     [Fedora Music]     [Fedora Packaging]     [Centos]     [Fedora SELinux]     [Fedora Legal]     [Fedora Kernel]     [Fedora OCaml]     [Coolkey]     [Virtualization Tools]     [ET Management Tools]     [Yum Users]     [Tux]     [Yosemite News]     [Gnome Users]     [KDE Users]     [Fedora Art]     [Fedora Docs]     [Asterisk PBX]     [Fedora Sparc]     [Fedora Universal Network Connector]     [Libvirt Users]     [Fedora ARM]

  Powered by Linux