Re: LAN question

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Joel Rees wrote:

On Sep 15, 2008, at 1:56 PM, Paul Newell wrote:

Fedora:

Before I switched to F9, all my FC5 machines were happily chatting with each other through a Linksys WRT54GL but none of them could see the net.

How did you set this up originally? Apparently not DHCP, from what you've written about /etc/hosts, but what machine(s) did you specify as the name server(s)?

I upgraded one of them to F9 and it sees the net and can ssh to the others.

So, when you upgraded the one, you probably gave the install script a DNS server address or two?

But the other two machines can no longer ssh into it F9 system.

And I must admit, based on the /etc/hosts below, that I'm wondering how you did before. ssh to a numerical IP address, perhaps?

I tried to play with things to fix it, but the best I could do was kill the network connection so that the F9 system can't see the other machine or the net. In other words, I screwed up. Since I can't figure out how to get the network back alive by restoring prior conditions, I am resigned to yet another re-install (the price of learning is lots of starting over...)

If it's a slow machine, I hope you haven't already started. Waste a good learning opportunity.

Did you backup /etc/hosts before the upgrade, by the way?

That being said, I was hoping to get a bit of advice.

The following is the F9 /etc/hosts file after 1) a fresh install of f9 and 2) my additions (noted with comments):

   # Do not remove the following line, or various programs
   # that require network functionality will fail.
   127.0.0.1        chowder.localdomain chowder localhost.localdomain
   localhost chowder

Any reason to have chowder in there twice?

   ::1        localhost6.localdomain6 localhost6

   #-# 14sep08 (paul): self
   192.168.2.11    chowder

I usually don't put this line in, just leave the declaration with localhost to take care of it.

   #-# 14sep08 (paul): other machines available
   192.168.2.10    chalupa
   192.168.2.12    parsnip

The next section is from one of the FC5 machines:

   # Do not remove the following line, or various programs
   # that require network functionality will fail.
   127.0.0.1    localhost.localdomain    localhost

   #-# self
   192.168.2.12    parsnip

I would have put that up there on 127.0.0.1 like you did with chowder.

   #-# other machines available
   192.168.2.10    chalupa      192.168.2.11    chowder

Should we assume that somehow two lines got combined when you pasted that here, or is this the reason parsnip can't see chowder?

If that's one line in your hosts file, I'm pretty sure it would prevent parsnip from seeing chowder. In fact, it would likely make strange things happen, like mapping "192.168.2.11" (as a string) and "chowder" to to 192.168.2.10 along with chalupa. Just for parsnip, of course.

I am suspect of the "localdomain" in the F9 version, but trying to play with that is what killed network (LAN and internet) ability.

Hmm. What was the 127.0.0.1 line when chowder was seeing the internet? And did you specify any dns servers when you set up chowder?

I went through the system->admin->network stuff and couldn't see anything that looked wrong (then again, do I know what is right?)

As always, suggestions appreciated (including general pointers as to where to go online to learn more about all this)

Thanks,
Paul

[...]

I did want to add the following in case it makes any difference in your advice. My plan is to convert all the FC5 machines to F9 once I am confident in the F9 machine and my understanding of it. None of the machines are servers, they are three independent workstations that just need to ssh/scp/"s-etc" to each other. I would hope that each could independently access the internet and each other.

Have you got a file in /etc/sysconfig/network-scripts called ifcfg-eth0 or something similar? (ifcfg-something-other-than-lo)

Does it look something like this:
-----------------------------------
DEVICE=eth0
BOOTPROTO=none
BROADCAST=192.168.2.255
# HWADDR is your NIC's MAC address, six bytes in hexadecimal
HWADDR=00:0e:3a:b2:51:fc
IPADDR=192.168.2.11
NETMASK=255.255.255.0
NETWORK=192.168.2.0
ONBOOT=yes
DNS1=<your-isp-dns-server-1>
DNS2=<your-isp-dns-server-2>
# I don't remember what SEARCH is set to by default, maybe "localdomain"?
# (In my case it is the domain name I get from dyndns.com.)
SEARCH="localdomain"
# This next line was giving me trouble earlier because I had left it no,
# but was using network manager:
NM_CONTROLLED=yes
# GATEWAY would be the IP address of your Linksys.
GATEWAY=192.168.2.1
TYPE=Ethernet
# I'm not sure what USERCTL and PEERDNS do at this point.
USERCTL=no
PEERDNS=yes
IPV6INIT=no
------------------------------------

That file is used by the startup scripts when they call ifconfig to bring your NICs up, as I understand it.

Here's a page that will tell you more:

http://www.redhat.com/docs/manuals/enterprise/RHEL-3-Manual/ref-guide/s1-networkscripts-interfaces.html

(And I think I'll go review it, myself.)

Joel Rees

Joel:

First, as mentioned in a reply to Arthur, I've got a confirm that the issue is my inability to give the F9 machine a static IP w/ name as I can ssh in from other machines if I ifconfig the F9 machine to see its DHCP.

When I did the original install, I gave (on the network page):

network devices: left at default
hostname: chowder.localdomain
gateway: 192.168.2.2
primary DNS: empty
secondary DNS: empty

This ended up giving me network access, no sense of local static IP, a primary DNS resolved back to198.168.1.1 and the Gateway of myhome.westell.com.

I then tried a new install in which I changed the default network devices settings to:

(checked) enable IPv4 support
(not checked) DHCP
(checked) manual config with 192.168.2.11 / 255.255.255.0
(enable) IPv6 support
(checked) neighbor discovery
(not checked) DHCPv6
(not checked) manual config

This produced a broken network that I could never get working and nobody could ssh into the machine as well.

In the original FC5 setup, I could ssh via the machine's HOSTNAME or its static IP. I did backup the original /etc/hosts and included them in my last post to Arthur, plus the new F9 version after re-installing the original "default" way so I at least had the network working.

No way around re-installing, it seems that once I get in a bad state I can't undo it due to lack of knowledge. For the manual config, I did the reinstall(s) and didn't bother doing yum update as I just wanted to see if network would work. Once I went back to original default, did proper install.

Regarding your question of having chowder in the 127.0.0.1 line, this is how F9 install created the file.

Your comments of not adding the 192.168.2.11 references to self make sense, except I am now pretty certain my problem is that I can't tell the F9 box that it is "chowder" and it has a static IP of 192.168.2.11. I thought this info went into /etc/hosts (???)

Correct on typo for cut-and-paste of parsnip, apologies.

Regarding the ifcfg-eth0, I am attaching the file and as you can see it is nowhere near what you thought it might look like and clearly indicates that I am DHCP and my issue is learning how to make the machine a static IP. I considered trying to cut-and-paste your version in to see what happened, but I felt like that could be a newbie-hurts-self exercise as I have no idea what other settings might be assuming the old version.

I read the link you provided, read it again, then read it again. Sure makes it seem like I should be able to cut-and-paste, but I'm still trying to understand parts of the info as I am wary of parroting something I don't really understand. I get the DHCP versus the page's notes on "system using a fixed address" (8.2.1), but the other sections are confusing and I can't tell if they apply or not to my situation.

Wondering if I ought to convert another one of the FC5 machines to F9 with a manual config w/ address and see if I can figure out (probably includes asking for help (smile) to get closer to the ifcfg you suggested (keeping chowder in its current state so I at least have a usable machine that I can begin exercising and reinstalling backed up personal stuff so I can start using it ... plus have web access for the link you gave me as right now the Linux is in one room on one floor and, unless it has internet, I have to go to my Windows box in another room on another floor and that just a lousy way to work!)

Sorry for the delay in getting back, I can only work on this stuff over the weekend. Suggestions appreciated.

Thanks,
Paul


# Intel Corporation 82557/8/9/0/1 Ethernet Pro 100
DEVICE=eth0
BOOTPROTO=dhcp
HWADDR=00:e0:81:00:62:94
ONBOOT=yes
DHCP_HOSTNAME=chowder.localdomain
NM_CONTROLLED=
-- 
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
[Index of Archives]     [Older Fedora Users]     [Fedora Announce]     [Fedora Package Announce]     [EPEL Announce]     [Fedora Magazine]     [Fedora News]     [Fedora Summer Coding]     [Fedora Laptop]     [Fedora Cloud]     [Fedora Advisory Board]     [Fedora Education]     [Fedora Security]     [Fedora Scitech]     [Fedora Robotics]     [Fedora Maintainers]     [Fedora Infrastructure]     [Fedora Websites]     [Anaconda Devel]     [Fedora Devel Java]     [Fedora Legacy]     [Fedora Desktop]     [Fedora Fonts]     [ATA RAID]     [Fedora Marketing]     [Fedora Management Tools]     [Fedora Mentors]     [SSH]     [Fedora Package Review]     [Fedora R Devel]     [Fedora PHP Devel]     [Kickstart]     [Fedora Music]     [Fedora Packaging]     [Centos]     [Fedora SELinux]     [Fedora Legal]     [Fedora Kernel]     [Fedora OCaml]     [Coolkey]     [Virtualization Tools]     [ET Management Tools]     [Yum Users]     [Tux]     [Yosemite News]     [Gnome Users]     [KDE Users]     [Fedora Art]     [Fedora Docs]     [Asterisk PBX]     [Fedora Sparc]     [Fedora Universal Network Connector]     [Libvirt Users]     [Fedora ARM]

  Powered by Linux