On Fri, 2008-02-22 at 18:29 -0500, max wrote: > Sean Bruno wrote: > > On Fri, 2008-02-22 at 17:40 -0500, max wrote: > >> Sean Bruno wrote: > >>>> > >>>> > >>>> > -- > >>>> Can you post the output of lspci -vv for your modem please? > >>>> > >>>> Sean > >>>> > >>>> - > >>>> > >>>> Here you go and thanks for the help. > >>>> > >>>> > >>>> 01:09.0 Communication controller: Conexant HCF 56k Data/Fax Modem (rev > >>>> 08) > >>>> Subsystem: Aztech System Ltd Dell Mercury - MDP3880-U(B) Data Fax > >>>> Modem > >>>> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > >>>> ParErr- Stepping- SERR- FastB2B- DisINTx- > >>>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > >>>> <TAbort- <MAbort- >SERR- <PERR- INTx- > >>>> Latency: 32 > >>>> Interrupt: pin A routed to IRQ 11 > >>>> Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size=64K] > >>>> Region 1: I/O ports at 9000 [size=8] > >>>> Capabilities: [40] Power Management version 2 > >>>> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=55mA PME(D0 > >>>> +,D1-,D2-,D3hot+,D3cold-) > >>>> Status: D0 PME-Enable- DSel=0 DScale=0 PME- > >>>> > >>>> > >>>> Thanks, > >>>> > >>>> Max > >>> Isn't this one of those s/w modems? I think you will need to buy the > >>> "conextant" drivers or use the NDIS wrapper with the windows driver. > >>> > >>> http://www.linuxant.com > >> I didn't think it was but you maybe right. I read that a great many > >> conextant modems were compatible which is why I went with that modem. I > >> will have to double check to make sure this one is hardware modem, can > >> you tell by looking at the board?what would i look for? Would > >> ndiswrapper give me all the functionality i need here? I have a somewhat > >> large collection of internal modems at my disposal. Does anyone know of > >> an internal modem that is compatible with linux? It doesn't have to be > >> red hat based linux , though that is my preference. I appreciate the help. > >> > >> Max > >> > > I think that the easiest way to tell is to visually inspect the board. > > The ones that have a large amount of components, in my experience, are > > h/w modems. > > > > Also, if you put the modem into your box and you can see a TTY appear in > > the boot dmesg(dmesg|grep -i tty), then linux has recognized and > > assigned it to a serial interface and you should be good to go. > > > > Sean > > > > > My modem is recognized. It is a different card than before. > > $dmesg | grep -i tty > console [tty0] enabled > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > > then : > $wvdialconf /etc/wvdial.conf > Editing `/etc/wvdial.conf'. > > Scanning your serial ports for a modem. > > ttyS0<Info>: Device or resource busy > Modem Port Scan<*1>: S0 > ttyS1<Info>: Device or resource busy > Modem Port Scan<*1>: S1 > ttyS2<Info>: Device or resource busy > Modem Port Scan<*1>: S2 > ttyS3<Info>: Device or resource busy > Modem Port Scan<*1>: S3 > > > Sorry, no modem was detected! Is it in use by another program? > Did you configure it properly with setserial? > > > This is where i got stuck before. I am not using setserial properly. I > can execute the command but i am assigning the wrong values i think but > my syntax is ok or I would get an error from bash. One thing,at least, > is clear, i do not understand the setserial command or what to set the > values to. > > > Thanks, > > Max > I see two serial ports, does your machine have two physical serial ports. Are they conflicting with your modem perchance? Sean -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
