On Fri, 2008-01-25 at 22:41 +0200, Gilboa Davara wrote: > What kind of RAID is it? > SATA? SCSI? > What chipset are you using? > Motherboard? > > - Gilboa > It has raid on the MOBO but I don't remember how we set it up originally (way back when with Fedora 3). I don't remember if we used the raid on the MOBO or did it via software. [root@bilonick log]# lspci 00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07) 00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05) 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03) 00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02) 00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05) 00:07.5 Multimedia audio controller: Advanced Micro Devices [AMD] AMD-8111 AC97 Audio (rev 03) 00:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) 00:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) 00:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) 00:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 02:09.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703X Gigabit Ethernet (rev 02) 03:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b) 03:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b) 03:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 03:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) 04:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-8151 System Controller (rev 14) 04:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8151 AGP Bridge (rev 14) 05:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (rev 01) 05:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (Secondary) (rev 01) As I said previously, once I switched to the vesa driver, I get a 1280x 1040 display. I looked at the X log when trying the radeon driver - I don't see any problems - it correctly identifies the monitor as a Dell P1110 and knows that it can do up to 1800x1440. But when using the radeon driver with Fedora 8, the display looks like old analog TV with a rolling, distorted screen that is unusable. (It works fine under Fedora 7 and all the way back to Fedora 3). I got nowhere with the ATI proprietary flgrx driver (from their web page) but was able to install this via an rpm from livna. I did this remotely so I won't be able to really try this driver until I go back to the office on Monday. Rick -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
