On Dec 5, 2007 11:33 PM, Nigel Henry <cave.dnb@xxxxxxxxxx> wrote: > > > > > Another thing. Are you sure that ntp isn't doing it's stuff, even > > > > > though the bootup shows a fail. Before you do the ntpd restart, run > > > > > the following as user. > > > > > > > > > > /usr/sbin/ntpq > > > > > then type pe, which will give you some info on which servers ntp is > > > > > trying to connect to, and how successfull it is being. You can keep > > > > > typing pe at intervals, which will show ntp's progress at reaching a > > > > > point where a time server is being used as a "sys peer". The server > > > > > being used will be prefixed by a "*". Other useable servers will be > > > > > prefixed by a "+" "candidat". To quit ntpq type q. > > > > > > > > Thanks, Nigel. In fact, > > > > # /usr/sbin/ntpq > > > > ntpq> pe > > > > No association ID's returned > > > > ntpq> pe > > > > remote refid st t when poll reach delay offset > > > > jitter > > > > ======================================================================= > > > >==== === clock-a.develoo 192.12.19.20 2 u 28 64 3 190.143 > > > > 438.261 9.311 ntpq> > > > > > > Well it appears to have a connection to the timeserver here, and often > > > takes a while before the timeserver is accepted as a system peer. Then an > > > "*" will appear before clock-a.develoo. Your reach is showing as 3, and > > > will gradually progress until it reaches 377, but this can take some > > > time. > > > > > > > i.e., when I run pe after a while, I get the above, but the first time > > > > I run pe, I get > > > > > > > > 'No association ID's returned' > > > > > > That usually indicates that ntp cannot contact the timeserver, no network > > > connection, or the timeserver is not accessable. > > > > > > > Can I be sure that ntp is running now and synchronizing with a ntp > > > > server? > > > > > > It appears to be running, but I think you have a problem in only having > > > one timeserver available. > > > > > > > Paul > > > > > > Paul. I'd still suggest that you add more timeservers to your > > > /etc/ntp.conf. Try the 3 that I am using. I know they are not the closest > > > to you, but they have been reliable for me. As I mentioned earlier, make > > > sure that everything in /etc/ntp.conf is commented out, except the > > > driftfile line, comment out also your present server, and add the ones > > > I've listed below. Save the changes, restart the ntp daemon, and rerun > > > /usr/sbin/ntpq. Type pe every minute or so, and see how it progresses. > > > > > > server ntp.obspm.fr > > > server ntp.kamino.fr > > > server ntp2.belbone.be > > > > > > Is this just the one machine you have connected to the Internet, or are > > > you on a LAN with other machines that are also using ntp to get their > > > time from Internet timeservers? > > > > Thanks again, Nigel. Does it seem that it is working now? > > > > # /usr/sbin/ntpq > > ntpq> pe > > remote refid st t when poll reach delay offset > > jitter > > =========================================================================== > >=== *syrte8.obspm.fr 134.157.254.19 2 u 27 64 377 62.413 132.612 > > 16.037 +ns1.kamino.fr 193.52.184.106 2 u 20 64 377 85.748 > > 119.231 10.125 +ntp2.belbone.be 195.13.23.6 2 u 54 64 377 > > 69.566 104.344 12.046 ntpq> > > > > No, I am directly connected to the Internet, with no LAN in between. > > > > Paul > > That looks fine, and just what I'd expect to see. I have just noticed that at booting, the Network Manager daemon is loaded after the ntp one. This may be the cause of the problem. Paul -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
