On Nov 24, 2007 3:39 PM, Les <hlhowell@xxxxxxxxxxx> wrote: > > On Mon, 2007-11-19 at 09:17 -0800, Les wrote: > > Hi, everyone, > > I have a problem with mounting CF disks via a printer, an HP Photosmart > > 1215 with the disk slot in the side. It used to work. Hald is running, > > the printer is found by CUPS, but the CF's don't mount. I looked to see > > if I could find an error message, but didn't see one. The printer shows > > a green LED when it recognizes the disk, and that appears. > > > > In the past inserting the card would bring up an icon automatically. > > > > I don't remember doing anything at all to get this to work before. > > Where should I look and what should I look for? > > > > Thanks, > > Les H > > > > Here is the content of lsusb > > Bus 005 Device 003: ID 059b:007e Iomega Corp. > > Bus 005 Device 001: ID 0000:0000 > > Bus 004 Device 001: ID 0000:0000 > > Bus 003 Device 001: ID 0000:0000 > > Bus 002 Device 014: ID 03f0:3202 Hewlett-Packard > > Bus 002 Device 013: ID 0518:0001 EzKEY Corp. > > Bus 002 Device 012: ID 0451:2046 Texas Instruments, Inc. TUSB2046 Hub > > Bus 002 Device 011: ID 0451:2046 Texas Instruments, Inc. TUSB2046 Hub > > Bus 002 Device 001: ID 0000:0000 > > Bus 001 Device 001: ID 0000:0000 > > > > > > > > Here is the content of lspci: > > 00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM > > Controller/Host-Hub Interface (rev 02) > > 00:01.0 PCI bridge: Intel Corporation 82865G/PE/P PCI to AGP Controller > > (rev 02) > > 00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB > > UHCI Controller #1 (rev 02) > > 00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB > > UHCI Controller #2 (rev 02) > > 00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB > > UHCI Controller #3 (rev 02) > > 00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB > > UHCI Controller #4 (rev 02) > > 00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 > > EHCI Controller (rev 02) > > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) > > 00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC > > Interface Bridge (rev 02) > > 00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE > > Controller (rev 02) > > 00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller > > (rev 02) > > 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus > > Controller (rev 02) > > 00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER > > (ICH5/ICH5R) AC'97 Audio Controller (rev 02) > > 01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX > > 5200] (rev a1) > > 02:02.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host > > Controller (rev 46) > > 02:04.0 Communication controller: Agere Systems LT WinModem (rev 02) > > 02:08.0 Ethernet controller: Intel Corporation 82562EZ 10/100 Ethernet > > Controller (rev 01) > > > > > I know it is bad form to reply to your own message, but anyway.... > I couldn't find any information to assist me with this issue, so I > finally just put one of those cheap "card reader" things on USB and > bingo, the CF's automounted and I was able to copy the files and use > them. Not the perfect solution, but it got me going again. > > Regards, > Les H Do you have hplip and hplip-gui installed? -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
