Carroll Grigsby wrote:
On Sunday 28 October 2007 12:28:56 pm Karl Larsen wrote:
Ralf Corsepius wrote:
On Sun, 2007-10-28 at 12:00 -0400, Carroll Grigsby wrote:
According to the Soyo site, your motherboard has an onboard Prosavage
graphics chip (http://www.soyousa.com/products/proddesc.php?t=d&id=292),
and uses a VIA chipset. Nothing there about nVidia, so I assume that the
nVidia card is an add-on.
/sbin/lspci probably will tell.
Ralf
Thanks Ralf, you are right again. Here is a whole list of nvidia
hardware:
[root@k5di ~]# lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:05.0 VGA compatible controller: nVidia Corporation C51G [GeForce
6100] (rev a2)
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3)
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3)
00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a3)
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1)
00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller
(rev a1)
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2)
00:10.2 Multimedia audio controller: nVidia Corporation MCP51 AC97 Audio
Controller (rev a2)
00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
[root@k5di ~]#
And the video controller is a nVidia Corporation C51G [GeForce 6100]
(rev a2) what ever that might mean. Also the entire computer is full of
nvidia things and the only one causing trouble is the video.
Karl:
First, whatever Soyo board that you have, it certainly isn't the model number
that you cited above.
Second, unlike video cards, onboard chips _usually_ rely on system RAM rather
than onboard RAM. If that is the case here, you have to reserve some memory
space for the use of the chip by using a mem=XXXX command at boot time. (xxxx
is the difference between the installed RAM and that required by the video
card). I've never dealt with one of these onboard critters, so I'll leave it
to you to determine the exact form of the mem command. In particular, be
careful about expressing the amount of memory -- I'm not certain whether it's
in kilobytes, megabyte or whatever.
-- cmg
Gads, I thought that was what the kernel does. Why must I tell it to
save RAM? Part of the Nvidia software is a kernel package which might
take care of this. At least I do not have any kernel stuff like that in
my grub.conf.
--
Karl F. Larsen, AKA K5DI
Linux User
#450462 http://counter.li.org.
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
