Hi,
I need help to set up D-Link DWL-G510 wireless G Desktop Adapter on my
Fedora 7 box.
I have installed madwifi through Yum. system-config-network detects
RaLink RT2561/RT61 re card.
When I activate the card I get this message:
------------------------------------------------------------------------
SIOCSIFFLAGS: No such file or directory
Determining IP information for wlan0...SIOCSIFFLAGS: No such file or
directory
SIOCSIFFLAGS: No such file or directory
failed.
------------------------------------------------------------------------
How can I get this work? Any help is appreciated.
I have pasted the iifconfig and dmesg information below.
[root@localhost ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0A:E6:C9:DE:3A
inet addr:192.168.1.100 Bcast:192.168.1.255
Mask:255.255.255.0
inet6 addr: fe80::20a:e6ff:fec9:de3a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12752 errors:0 dropped:0 overruns:0 frame:0
TX packets:11754 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:11865535 (11.3 MiB) TX bytes:1990141 (1.8 MiB)
Interrupt:22 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3287 errors:0 dropped:0 overruns:0 frame:0
TX packets:3287 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9874220 (9.4 MiB) TX bytes:9874220 (9.4 MiB)
------------------------------------------------------------------------
[root@localhost ~]# dmesg
Linux version 2.6.22.9-91.fc7
(kojibuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.2 20070502
(Red Hat 4.1.2-12)) #1 SMP Thu Sep 27 23:10:59 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bff0000 (usable)
BIOS-e820: 000000001bff0000 - 000000001bff3000 (ACPI NVS)
BIOS-e820: 000000001bff3000 - 000000001c000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
447MB LOWMEM available.
found SMP MP-table at 000f5d40
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 114672) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 114672
HighMem 114672 -> 114672
early_node_map[1] active PFN ranges
0: 0 -> 114672
On node 0 totalpages: 114672
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 863 pages used for memmap
Normal zone: 109713 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000F7B40, 0014 (r0 AWARD )
ACPI: RSDT 1BFF3000, 002C (r1 AWARD AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 1BFF3040, 0074 (r1 AWARD AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 1BFF30C0, 39E0 (r1 AWARD AWRDACPI 1000 MSFT 100000E)
ACPI: FACS 1BFF0000, 0040
ACPI: APIC 1BFF6AC0, 007C (r1 AWARD AWRDACPI 42302E31 AWRD 0)
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1c000000:e2c00000)
Built 1 zonelists. Total pages: 113777
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0791000 soft=c0771000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 2489.839 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 446800k/458688k available (2108k kernel code, 11200k reserved,
1112k data, 260k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
lowmem : 0xc0000000 - 0xdbff0000 ( 447 MB)
.init : 0xc072b000 - 0xc076c000 ( 260 kB)
.data : 0xc060f3a8 - 0xc0725504 (1112 kB)
.text : 0xc0400000 - 0xc060f3a8 (2108 kB)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 4982.08 BogoMIPS
(lpj=2491043)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebf3ff 00000000 00000000 0000b080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) 4 CPU 2.50GHz stepping 09
Total of 1 processors activated (4982.08 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1536 bytes
Time: 13:49:19 Date: 10/18/07
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfba90, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Enabling SiS 96x SMBus.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:00: iomem range 0xc0000-0xeffff could not be reserved
pnp: 00:00: iomem range 0xf0000-0xf3fff could not be reserved
pnp: 00:00: iomem range 0xf4000-0xf7fff could not be reserved
pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: ed000000-ed0fffff
PREFETCH window: e0000000-e7ffffff
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2831k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1192715359.447:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 1C0E7986B75803D3
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is
not present [20070126]
ACPI: Thermal Zone [THRM] (40 C)
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected SiS chipset - id:1617
agpgart: AGP aperture is 64M @ 0xe8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Magic number: 11:542:837
Freeing unused kernel memory: 260k freed
Write protecting the kernel read-only data: 858k
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 16
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: irq 16, io mem 0xed11c000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 17
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: irq 17, io mem 0xed118000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 18
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.2: irq 18, io mem 0xed119000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 19
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: irq 19, io mem 0xed11a000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
pata_sis 0000:00:02.5: version 0.5.2
ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 20
scsi0 : pata_sis
scsi1 : pata_sis
ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00014000
irq 14
ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x00014008
irq 15
ata1.01: ATA-5: WDC WD400EB-11CPF0, 06.04G06, max UDMA/100
ata1.01: 78165360 sectors, multi 16: LBA
ata1.01: configured for UDMA/100
ata2.01: ATAPI: ATAPI CDROM 48X, V200R, max UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:1:0: Direct-Access ATA WDC WD400EB-11CP 06.0 PQ: 0
ANSI: 5
sd 0:0:1:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:1:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2
sd 0:0:1:0: [sda] Attached SCSI disk
scsi 1:0:1:0: CD-ROM ATAPI CDROM 48X 200R PQ: 0
ANSI: 5
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1192715364.949:2): selinux=0 auid=4294967295
sd 0:0:1:0: Attached scsi generic sg0 type 0
scsi 1:0:1:0: Attached scsi generic sg1 type 5
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:1:0: Attached scsi CD-ROM sr0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x10c0
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:00:0d.0: This (id 10ec:8139 rev 10) is not an 8139C+
compatible chip
8139cp 0000:00:0d.0: Try the "8139too" driver instead.
ACPI: PCI Interrupt 0000:00:02.3[B] -> GSI 17 (level, low) -> IRQ 21
8139too Fast Ethernet driver 0.9.28
firewire_ohci: Added fw-ohci device 0000:00:02.3, OHCI version 1.0
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 22
eth0: RealTek RTL8139 at 0xdc8e8000, 00:0a:e6:c9:de:3a, IRQ 22
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 21
phy0: Selected rate control algorithm 'simple'
firewire_core: created new fw device fw0 (0 config rom retries)
ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 23
intel8x0_measure_ac97_clock: measured 50859 usecs
intel8x0: clocking to 48000
loop: module loaded
lp0: using parport0 (interrupt-driven).
lp0: console ready
sonypi: Sony Programmable I/O Controller Driver v1.26.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
No dock devices found.
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input5
ACPI: Sleep Button (CM) [FUTS]
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@xxxxxxxxxx
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda1, internal journal
Adding 2048276k swap on /dev/sda2. Priority:-1 extents:1
across:2048276k
IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
audit(1192695589.776:3): audit_pid=1600 old=0 by auid=4294967295
eth0: no IPv6 routers present
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
eth0: no IPv6 routers present
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
eth0: no IPv6 routers present
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
[root@localhost ~]#
------------------------------------------------------------------------
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
