Hi all,
I've recently installed Linux Fedora Core 7 onto a Pentium III 800Mhz computer.
Everything went OK but when I boot a message appeared going something like:
ata1.01: Exception Emask 0x0
BDMA stat 0x64
Googled it up but found nothing conclusive. Could it be a hard drive problem? It
would be strange since there's no SMART warnings and this computer used to have
WinXP and no disk problem ever ocurred.
'dmesg' output attached.
thanks in adv
FG
Linux version 2.6.22.7-85.fc7 (kojibuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.2 20070502 (Red Hat 4.1.2-12)) #1 SMP Fri Sep 21 19:53:05 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000030000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
768MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 196608) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 196608
HighMem 196608 -> 196608
early_node_map[1] active PFN ranges
0: 0 -> 196608
On node 0 totalpages: 196608
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1504 pages used for memmap
Normal zone: 191008 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
Allocating PCI resources starting at 40000000 (gap: 30000000:cfff0000)
Built 1 zonelists. Total pages: 195072
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet acpi=off
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0160e000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0793000 soft=c0773000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 866.413 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 771020k/786432k available (2111k kernel code, 14836k reserved, 1117k data, 260k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf0800000 - 0xff7fe000 ( 239 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
.init : 0xc072d000 - 0xc076e000 ( 260 kB)
.data : 0xc060fde8 - 0xc0727504 (1117 kB)
.text : 0xc0400000 - 0xc060fde8 (2111 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 1733.86 BogoMIPS (lpj=866933)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f1ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
CPU0: Intel Pentium III (Coppermine) stepping 06
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1536 bytes
Time: 2:29:51 Date: 10/15/07
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb230, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0596] at 0000:00:07.0
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: e4000000-e7ffffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3496k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1192415392.001:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 5C8CFCE5A817ACD0
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Activating ISA DMA hang workarounds.
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Generic RTC Driver v1.07
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Magic number: 11:286:460
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 260k freed
Write protecting the kernel read-only data: 864k
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x0000e400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
SCSI subsystem initialized
usb 1-1: new low speed USB device using uhci_hcd and address 2
libata version 2.21 loaded.
pata_via 0000:00:07.1: version 0.3.1
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/66 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001e000 irq 14
ata2: PATA max UDMA/66 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001e008 irq 15
usb 1-1: configuration #1 chosen from 1 choice
input: Logitech Optical USB Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:07.2-1
ata1.00: ATA-6: ST380011A, 3.06, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48
ata1.01: ATA-6: ST380011A, 8.54, max UDMA/100
ata1.01: 156301488 sectors, multi 16: LBA48
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
ata2.00: ATAPI: PIONEER DVD-RW DVR-107D, 1.15, max UDMA/33
ata2.01: ATAPI: HL-DT-STDVD-ROM GDR8162B, 0015, max UDMA/33
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA ST380011A 3.06 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 0:0:1:0: Direct-Access ATA ST380011A 8.54 PQ: 0 ANSI: 5
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 0:0:1:0: [sdb] Attached SCSI disk
scsi 1:0:0:0: CD-ROM PIONEER DVD-RW DVR-107D 1.15 PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM HL-DT-ST DVD-ROM GDR8162B 0015 PQ: 0 ANSI: 5
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:04:4d:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 2048 in
res 51/84:01:50:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:04:4d:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 2048 in
res 51/84:01:50:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:04:4d:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 2048 in
res 51/84:01:50:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
ata1: EH complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
ata1.01: limiting speed to UDMA/44:PIO4
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:04:4d:00:00/00:00:00:00:00/f0 tag 0 cdb 0x0 data 2048 in
res 51/84:01:50:00:00/00:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/44
ata1: EH complete
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1192415402.989:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1845 types, 82 bools, 1 sens, 1024 cats
security: 61 classes, 70170 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1192415403.451:3): policy loaded auid=4294967295
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
scsi 1:0:0:0: Attached scsi generic sg2 type 5
scsi 1:0:1:0: Attached scsi generic sg3 type 5
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 20x/48x cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux Tulip driver version 1.1.15 (Feb 27, 2007)
PCI: setting IRQ 10 as level-triggered
PCI: Found IRQ 10 for device 0000:00:0c.0
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1.
eth0: Digital DS21142/43 Tulip rev 65 at MMIO 0xe9000000, 00:C0:F0:4A:CF:65, IRQ 10.
PCI: setting IRQ 11 as level-triggered
PCI: Found IRQ 11 for device 0000:00:09.0
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1572856k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:1572856k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd 35/00:00:6f:42:00/00:04:00:00:00/f0 tag 0 cdb 0x0 data 524288 out
res 51/84:00:6f:42:00/84:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/44
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd 35/00:00:6f:42:00/00:04:00:00:00/f0 tag 0 cdb 0x0 data 524288 out
res 51/84:00:6f:42:00/84:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/44
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
audit(1192415436.994:4): audit_pid=1315 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
eth0: Setting half-duplex based on MII#1 link partner capability of 4021.
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd ca/00:30:bf:01:98/00:00:00:00:00/f8 tag 0 cdb 0x0 data 24576 out
res 51/84:00:bf:01:98/84:00:00:00:00/f8 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/44
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
eth0: no IPv6 routers present
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (6144 buckets, 49152 max)
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
ata1.01: limiting speed to UDMA/33:PIO4
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd 35/00:60:87:7a:00/00:01:00:00:00/f0 tag 0 cdb 0x0 data 180224 out
res 51/84:00:87:7a:00/84:00:00:00:00/f0 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:88:a7:0a:fa/00:00:00:00:00/f4 tag 0 cdb 0x0 data 69632 in
res 51/84:01:2e:0b:fa/84:00:00:00:00/f4 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:88:a7:0a:fa/00:00:00:00:00/f4 tag 0 cdb 0x0 data 69632 in
res 51/84:01:2e:0b:fa/84:00:00:00:00/f4 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:88:a7:0a:fa/00:00:00:00:00/f4 tag 0 cdb 0x0 data 69632 in
res 51/84:01:2e:0b:fa/84:00:00:00:00/f4 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:20:cf:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 16384 in
res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
sd 0:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 0:0:1:0: [sdb] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
03 43 41 ee
sd 0:0:1:0: [sdb] Add. Sense: Scsi parity error
end_request: I/O error, dev sdb, sector 54739407
ata1: EH complete
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:08:e7:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 4096 in
res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/33
ata1: EH complete
ata1.01: limiting speed to PIO4
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.01: (BMDMA stat 0x64)
ata1.01: cmd c8/00:08:e7:41:43/00:00:00:00:00/f3 tag 0 cdb 0x0 data 4096 in
res 51/84:01:ee:41:43/84:00:00:00:00/f3 Emask 0x10 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1.01: configured for PIO4
ata1: EH complete
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Clocksource tsc unstable (delta = 143851066 ns)
Time: pit clocksource has been installed.
spurious 8259A interrupt: IRQ7.
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
