Re: Eth1 problems again [ Solved - for the moment]

[david walcroft <d_j_w46@xxxxxxxxxxxxxx>]

Craig White wrote:
> On Thu, 2007-10-04 at 10:59 +1000, david walcroft wrote:
>   
> > Timothy Murphy wrote:
> >     
> > >   
> > >       
> > Eth0 is dhcp,Ethe1 is static 192.168.0.1
> >     
> > > What does "ifconfig eth1" say?
> > >   
> > >       
> > [david@reddwarf ~]$ ifconfig eth1
> > eth1      Link encap:Ethernet  HWaddr 00:E0:4C:14:1B:09
> >           inet6 addr: fe80::2e0:4cff:fe14:1b09/64 Scope:Link
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
> >           RX packets:3 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:1000
> >           RX bytes:747 (747.0 b)  TX bytes:578 (578.0 b)
> >           Interrupt:22 Base address:0x8c00
> >     
> ----
> nope - ip address doesn't show...there's an error
> ----
>   
> > [david@reddwarf ~]$
> >     
> > > What does "route" say?
> > >   
> > >       
> > [david@reddwarf ~]$ route
> > Kernel IP routing table
> > Destination     Gateway         Genmask         Flags Metric Ref    Use 
> > Iface
> > 121.208.32.0    *               255.255.248.0   U     0      0        0 eth0
> > 169.254.0.0     *               255.255.0.0     U     0      0        0 eth0
> > default         121.208.32.1    0.0.0.0         UG    0      0        0 eth0
> > [david@reddwarf ~]$
> >     
> > > What is in /etc/sysconfig/network-scripts/ifcfg-eth1?
> > >   
> > >       
> > # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
> > DEVICE=eth1
> > ONBOOT=yes
> > BOOTPROTO=none
> > HWADDR=00:e0:4c:14:1b:09
> > NETMASK=255.255.255.0
> > IPADDR=192.168.0.1
> > GATEWAY=192.168.0.0
> > TYPE=Ethernet
> > USERCTL=no
> > IPV6INIT=no
> > PEERDNS=yes
> >     
> ----
> GATEWAY is a bad address... that's a network address
>
> comment out GATEWAY...you already have a GATEWAY address per above
> (121.208.32.1)
> comment out PEERDNS...that's for BOOTPROTO=dhcp
> comment out BOOTPROTO
>
> after you change these settings...
>
> try...
>
> ifup eth1
> ----
>   
> > [david@reddwarf ~]$ sudo ping -c 5 192.168.0.2
> > PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data.
> > ping: sendmsg: Operation not permitted
> > ping: sendmsg: Operation not permitted
> > ping: sendmsg: Operation not permitted
> > ping: sendmsg: Operation not permitted
> > ping: sendmsg: Operation not permitted
> >
> > What do I do to get ping to work  and is it part of this problem overall.
> > 192.168.0.2 is on the other end of my crossover cable
> >     
> ----
> should work
>
> Craig
>
>   
Thanks Craig It's up and running and 192.168.0.2 is on the net
But pinging only provides me with lost packets to 192.168.0.2
I can ping 192.168.0.1 and 121.208.32.1 my gateway.

Thanks a lot Craig
  
  david

--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list