On Mon, 2007-09-24 at 17:09 -0700, Rick Stevens wrote: > On Mon, 2007-09-24 at 16:58 -0500, Aaron Konstam wrote: > > On Mon, 2007-09-24 at 19:43 +0200, Gilboa Davara wrote: > > > On Mon, 2007-09-24 at 13:34 -0400, Jon Shorie wrote: > > > > Does anyone know how I can find out the speed of my network connection on a > > > > fedora machine? > > > > > > > > On my ubunto boxen, I do a > > > > > > > > dmesg | grep eth0 > > > > > > > > and it usually tells me > > > > > > > > something like: > > > > > > > > [ 24.527986] eth0: no IPv6 routers present > > > > [ 2466.508627] e1000: eth0: e1000_watchdog: NIC Link is Down > > > > [ 2472.385648] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full > > > > Duplex > > > > > > > > but on fedora, I get: > > > > > > > > eth0: RTL8168b/8111b at 0xf883e000, 00:16:e6:6c:42:a1, IRQ 17 > > > > r8169: eth0: link up > > > > r8169: eth0: link up > > > > eth0: no IPv6 routers present > > > > r8169: eth0: link down > > > > r8169: eth0: link up > > > > > > > > a uname -r gives me: > > > > 2.6.20-1.2944.fc6 > > > > > > > > any suggestions? I want to know if I am getting a 100 or 1000 mb/s > > > > connection. > > > > > > > > Thank you > > > > > > > > Jon Shorie > > > > Systems Administrator > > > > Medina County Sanitary Engineers > > > > > > > > > > $ ethtool ethX > > ethtool does not do this for me. > > I get: > > ethtool eth1 > > Settings for eth1: > > Link detected: yes > > That's hard to believe for a wired card. > > Settings for eth0: > Supported ports: [ TP ] > Supported link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > 1000baseT/Full > Supports auto-negotiation: Yes > Advertised link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > Advertised auto-negotiation: Yes > ------> Speed: 100Mb/s > Duplex: Full > Port: Twisted Pair > PHYAD: 0 > Transceiver: internal > Auto-negotiation: on > Supports Wake-on: pumbg > Wake-on: g > Current message level: 0x00000033 (51) > Link detected: yes > > Is this a wireless card? If so, you need to use iwconfig and look > for the "Bit Rate" value: > > [root@golem3 ~]# iwconfig wlan0 > wlan0 IEEE 802.11g ESSID:"mynetwork" > Mode:Managed Frequency:2.452 GHz Access Point: > xx:xx:xx:xx:xx:xx > -------> Bit Rate=54 Mb/s > Retry min limit:7 RTS thr:off Fragment thr=2346 B > Encryption key:xxxx-xxxx-xxxx-xxxx-xxxx-xxxx-xx > Link Quality=100/100 Signal level=-39 dBm Noise level=-95 > dBm > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Exactly where in your posting did you say that ethtool only works on wired cards? ======================================================================= Your CHEEKS sit like twin NECTARINES above a MOUTH that knows no BOUNDS -- ======================================================================= Aaron Konstam telephone: (210) 656-0355 e-mail: akonstam@xxxxxxxxxxxxx -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
