Re: Alternative booting

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



oh ye gods, has this become the mailing list for the blind leading the
blind?


David Krings:
>> I gave up on getting GRUB to behave consistently in my setup. I 
>> squarely blame GRUB for that as there is no reason not to work properly.
>> Anyhow, what are the other reliable boot options other than a boot 
>> loader installed in MBR?

You can use whatever bootloader you fancy, but you'll probably have to
figure it out for yourself.  I think LILO is dead and buried by now, or
at least as far as Fedora is concerned.  But that one's sufficiently
fresh in its grave that you could probably find help in using it with
Fedora, if you *reeeeeaaallly* want to.

But I can't see that helping, much.  We have no details in David's
message about what the problem really is.  Most bootloaders depend on
something in the MBR, so if he's having MBR problems, I can't see
another MBR-dependent bootloader helping.


Karl Larsen:
>     Hi David, I this morning am having problems with Grub. But I think 
> the root cause of the problem is my computer's bios setting. Several 
> years ago I set everything up with all the hard drives using cable 
> select and it worked.
> 
>     Now I want to add a new hard drive and Grub has gone bonkers. I was 
> not able to get it done yet. But I think first I need to go back to 
> Master Slave which defines for grub which is hd0 and hd1. Right now it 
> switches and then the dumb thing can't boot.

Master and slave jumpers set the drive to believe that it is a master or
slave.  Cable-select does exactly the same thing, except that the
master/slave jumpers are now part of the 40-way IDE cabling.  You jumper
the drive to be use cable-select, *then* the drive's master or slave
status is set by which socket on the ribbon lead is plugged into it (one
of them has an open-circuit pin, the other has a short).

I keep seeing all sorts of silly mythologies about what cable-select,
and master and slave drive jumpering does.  Use one or the other, and
don't mix the two schemes together, that's about all you need to know
(yes, it's possible to mix them, but you have to be damn sure that you
don't connect and jumper things as if there were two masters or two
slaves).  Whichever scheme you're using, if you only have one drive on a
cable, make sure that the unused connector is the one in the middle.
And however many drives you have, make sure the motherboard end on an
80-wire cable, is plugged into the motherboard.

Once the drives are set to be master or slave, the rest of the system
(hardware & software) doesn't give a damn about how it was actually
done.  Only the drives, themselves, care which is master and slave, and
they only care which is which, not how it's done.

>     If I take the other hard drive clear out this hard drive immediately 
> becomes hd0 and grub is not working. It can't find hd1 :-)

This sort of thing tends to be because someone doesn't understand how
GRUB orders the drives (the first one is hd0, the second hd1, etc.), and
it doesn't care where they're connected.  Yet, when someone installs
GRUB, they use a different scheme (/dev/hda or /dev/sda) and installs it
to the other drive, or points it to get its second stage files at the
other drive (inside the /boot/ partition), without realising it.

On systems that have removable drives, it really helps if whatever's hd0
is always going to be considered the first drive, and you put all the
GRUB stuff on it.  This may mean changing BIOS boot orders so that
things like USB drives are later in the boot order.

-- 
(This box runs FC5, my others run FC4 & FC6, in case that's
 important to the thread.)

Don't send private replies to my address, the mailbox is ignored.
I read messages from the public lists.

-- 
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
[Index of Archives]     [Older Fedora Users]     [Fedora Announce]     [Fedora Package Announce]     [EPEL Announce]     [Fedora Magazine]     [Fedora News]     [Fedora Summer Coding]     [Fedora Laptop]     [Fedora Cloud]     [Fedora Advisory Board]     [Fedora Education]     [Fedora Security]     [Fedora Scitech]     [Fedora Robotics]     [Fedora Maintainers]     [Fedora Infrastructure]     [Fedora Websites]     [Anaconda Devel]     [Fedora Devel Java]     [Fedora Legacy]     [Fedora Desktop]     [Fedora Fonts]     [ATA RAID]     [Fedora Marketing]     [Fedora Management Tools]     [Fedora Mentors]     [SSH]     [Fedora Package Review]     [Fedora R Devel]     [Fedora PHP Devel]     [Kickstart]     [Fedora Music]     [Fedora Packaging]     [Centos]     [Fedora SELinux]     [Fedora Legal]     [Fedora Kernel]     [Fedora OCaml]     [Coolkey]     [Virtualization Tools]     [ET Management Tools]     [Yum Users]     [Tux]     [Yosemite News]     [Gnome Users]     [KDE Users]     [Fedora Art]     [Fedora Docs]     [Asterisk PBX]     [Fedora Sparc]     [Fedora Universal Network Connector]     [Libvirt Users]     [Fedora ARM]

  Powered by Linux