On Wed, 2007-07-18 at 08:36 +0200, Sjoerd Mullender wrote: > On 07/17/2007 07:59 PM, Craig White wrote: > > On Tue, 2007-07-17 at 10:46 -0700, Srikanth Konjarla wrote: > >> Craig White wrote: > >>> On Tue, 2007-07-17 at 10:23 -0700, Srikanth Konjarla wrote: > >>>> Craig White wrote: > >>>>> On Mon, 2007-07-16 at 15:13 -0500, Mikkel L. Ellertson wrote: > >>>>>> Craig White wrote: > >>>>>>> I am struggling trying to make a Palm T|X work on Fedora 7 > >>>>>>> > >>>>>>> The problem *may* lie with the fact that in order to make this box work > >>>>>>> (A Dell Optiplex 320), that I have to add 'pci=nomsi acpi=off' kernel > >>>>>>> params on bootup. > >>>>>>> > >>>>>>> udevinfo tells me all about the device. > >>>>>>> > >>>>>>> I can see the device exists when I plug it in and check it via > >>>>>>> > >>>>>>> ls -l /dev/ttyUSB* and > >>>>>>> ls -l /dev/pilot > >>>>>>> > >>>>>>> but even if I try (as root), > >>>>>>> > >>>>>>> pilot-xfer -l -p /dev/ttyUSB1 or pilot-xfer -l -p /dev/pilot show > >>>>>>> nothing at all > >>>>>>> > >>>>>>> Is the problem my kernel parameters? > >>>>>>> > >>>>>> It probably isn't your kernel parameters. If it were, then > >>>>>> /dev/ttyUSB0 and /dev/USB1 most likely not be created. What happens > >>>>>> if you use /dev/ttyUSB0? Or, if you have more then 2 ttyUSB* > >>>>>> entries, try using /dev/ttyUSB2. I don't remember if the T|X uses > >>>>>> the first or second USB serial port that is created when you hit sync... > >>>>> ---- > >>>>> OK - didn't know the impact of the kernel params > >>>>> > >>>>> # ls -l /dev/ttyUSB* > >>>>> crw-rw---- 1 root uucp 188, 0 2007-07-17 09:52 /dev/ttyUSB0 > >>>>> crw-rw---- 1 root uucp 188, 1 2007-07-17 09:52 /dev/ttyUSB1 > >>>>> > >>>>> and from dmesg... > >>>>> usb 4-2: new full speed USB device using ohci_hcd and address 6 > >>>>> usb 4-2: configuration #1 chosen from 1 choice > >>>>> visor 4-2:1.0: Handspring Visor / Palm OS converter detected > >>>>> usb 4-2: Handspring Visor / Palm OS converter now attached to ttyUSB0 > >>>>> usb 4-2: Handspring Visor / Palm OS converter now attached to ttyUSB1 > >>>>> > >>>>> but while the palm is using ttyUSB0/1 - I get nada... > >>>>> > >>>>> # pilot-xfer -l -p /dev/ttyUSB1 > >>>>> > >>>>> Listening for incoming connection on /dev/ttyUSB1... > >>>>> > >>>>> # pilot-xfer -l -p /dev/ttyUSB0 > >>>>> > >>>>> Listening for incoming connection on /dev/ttyUSB0... > >>>>> # > >>>>> > >>>>> but never anything else ;-( > >>>> As you can see the device files are owned and writable by only root. > >>>> There are couple of options that you can try, > >>>> > >>>> 1. change the permissions on device files as root. > >>>> # chmod 777 /dev/ttyUSB* > >>>> > >>>> Try to sync your palm. > >>> ---- > >>> you might note the "#" cli prompt which is typical for user root. > >>> > >>> Trying to sync the palm is rather pointless if you can't do a basic > >>> listing of the files on the palm from the pilot-xfer (pilot-link > >>> package) which is the base package that all of the GUI tools > >>> (JPilot/KPilot/GPilot) all use. > >>> ---- > >>>> 2. Review the udev rules for ttyUSB* under /etc/udev/rules.d. It is very > >>>> likely that the default mode is set to "0660". You can refer to > >>>> 50-udev.rules file. Here is a link from one of the old RH Magazines. > >>>> > >>>> http://www.redhat.com/magazine/002dec04/features/udev/ > >>> ---- > >>> I am all over the udev rules - I am a long time palm user but that is > >>> more for 'users' and I am simply trying to communicate with the palm via > >>> pilot-xfer which as stated above, is the basic toolset for accessing a > >>> palm. The udev rules are tilted towards user space and again, I am > >>> trying to work this through as root first. > >>> > >>> I am quite certain that this would work with FC-6 but that isn't the > >>> point...there is an issue with F7 and it would help if someone related > >>> what they have done to get a Palm working on F7 - especially one of the > >>> newer 'OS5' Palms > >>> > >> For whatever it is worth, i have added the following lines to > >> 50-udev.rules on F7 to get the palm sync work with jpilot (the palm > >> device is configured as /dev/ttyUSB0). I have found that this is missing > >> in F7 from that of FC6 (of course i had to change the MODE to 0777). > >> > >> KERNEL=="ttyUSB*", SYSFS{product}=="Palm Handheld*", SYMLINK+="pilot", > >> GROUP="uucp", MODE="0777" > >> KERNEL=="ttyUSB*", SYSFS{product}=="palmOne Handheld*", > >> SYMLINK+="pilot", GROUP="uucp", MODE="0777" > >> KERNEL=="ttyUSB*", SYSFS{product}=="Handspring Visor*", > >> SYMLINK+="pilot", GROUP="uucp", MODE="0777" > > ---- > > thanks - I already have the same thing except MODE="0666" (files not > > folders) but that is for user space and I can't get root to be able to > > talk to the palm device other than, per my original post, udevinfo can > > get the information from the palm but pilot-xfer/pilot-link cannot. > > > > I am reasonably certain that this issue is related to the newest palm > > devices with what they call 'lifedrive' > > > > http://www.pilot-link.org/node/253 > > I have a T|X which I backup on my F7 laptop (Dell Inspiron 8200). It is > relatively painless, but not completely. > > I have the following udev rule (I have a lot more, derived from, but not > identical to, the ones in /usr/share/pilot-link/udev/60-libpisock.rules): > > KERNEL=="ttyUSB*", SYSFS{idVendor}=="0830", SYSFS{idProduct}=="0061", > SYMLINK+="pilot", GROUP="uucp", MODE="0664" > > With this rule, there is a shortish window of opportunity to start > pilot-xfer after I push the hotsync button on the Palm side. If I am > too fast (or start it before I push the button), it doesn't work, and if > I am too late, it just hangs. > > I use /dev/pilot which is created (by udev) as a symlink to /dev/ttyUSB1 > (i.e. not /dev/ttyUSB0). ---- BING! Thanks Craig -- Craig White <craig@xxxxxxxxxxxxx> -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
