Hi List,
I just installed FC6 on my old computer. everything was fine until I rebooted computer. I did install in graphic mode. My S3 Savage4 video card (32MB RAM) and Benq FP767-12 LCD Monitor were correctly identified. However on boot display is going blank.
I tried Xorg -configure, which generated attached file, however did not resolve issue.
Attached below are Xorg.conf and Xorg.0.log: (last few lines).
Please let me know if any one wnat to see full log file.
I would appreciate help from list.
Thanks...
Rajesh
====================================
xorg.conf:
----------
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "unix/:7100"
FontPath "built-ins"
EndSection
Section "Module"
Load "vnc"
Load "record"
Load "dbe"
Load "glx"
Load "xtrap"
Load "dri"
Load "extmod"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
#DisplaySize 340 270 # mm
Identifier "Monitor0"
VendorName "BNQ"
ModelName "BenQ FP767-12"
### Comment all HorizSync and VertSync values to use DDC:
HorizSync 31.0 - 83.0
VertRefresh 56.0 - 76.0
Option "DPMS"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "NoAccel" # [<bool>]
#Option "HWCursor" # [<bool>]
#Option "SWCursor" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "Rotate" # [<str>]
#Option "UseBIOS" # [<bool>]
#Option "LCDClock" # <freq>
#Option "ShadowStatus" # [<bool>]
#Option "CrtOnly" # [<bool>]
#Option "TvOn" # [<bool>]
#Option "PAL" # [<bool>]
#Option "ForceInit" # [<bool>]
#Option "Overlay" # [<str>]
#Option "TransparencyKey" # [<str>]
#Option "ForceInit" # [<bool>]
#Option "DisableXVMC" # [<bool>]
#Option "DisableTile" # [<bool>]
#Option "DisableCOB" # [<bool>]
#Option "DRI" # [<bool>]
#Option "BCIforXv" # [<bool>]
#Option "DVI" # [<bool>]
#Option "BusType" # [<str>]
#Option "DmaType" # [<str>]
#Option "DmaMode" # [<str>]
#Option "AGPMode" # <i>
#Option "AGPSize" # <i>
Identifier "Card0"
Driver "savage"
VendorName "S3 Inc."
BoardName "Savage 4"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
====================================
Xorg.0.log: (last few lines)
-----------------------------
(**) Keyboard0: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(--) Mouse0: PnP-detected protocol: "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
(II) SAVAGE(0): [drm] removed 1 reserved context for kernel
(II) SAVAGE(0): [drm] unmapping 8192 bytes of SAREA 0xcfc4c000 at 0xb7f67000
FreeFontPath: FPE "unix/:7100" refcount is 2, should be 1; fixing.
