I ran:
modprobe sky2
and got some good feedback.
I then ran
ifup eth0
no output.
I ran:
ifconfig and got:
eth0 Link encap:Ethernet HWaddr 00:11:11:B2:ED:CC
inet addr:192.168.0.125 Bcast:192.168.0.125 Mask:255.255.255.255
inet6 addr: fe80::211:11ff:feb2:edcc/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:5702 (5.5 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:56 errors:0 dropped:0 overruns:0 frame:0
TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10761 (10.5 KiB) TX bytes:10761 (10.5 KiB)
vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
RX packets:144 errors:0 dropped:0 overruns:0 frame:0
TX packets:4774 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:14876 (14.5 KiB) TX bytes:1471983 (1.4 MiB)
xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING NOARP MTU:1500 Metric:1
RX packets:4469 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1371625 (1.3 MiB) TX bytes:0 (0.0 b)
Finally, I ran
ping 192.168.0.1 (my router)
I got unable to reach network.
I feel like there is a step I forgot.
-----Original Message-----
From: fedora-list-bounces@xxxxxxxxxx
[mailto:fedora-list-bounces@xxxxxxxxxx]On Behalf Of GérardMilmeister
Sent: Wednesday, November 29, 2006 2:36 PM
To: For users of Fedora
Subject: Re: FC6 and Marvell Yukon network card
On Wed, 2006-11-29 at 14:20 -0700, Don Raikes wrote:
> Hello,
>
> I just installed FC6 on my gateway computer. The computer has a Marvell Yukon 88E8050 network chipset, and now I have no network support.
>
> I found a copy of the sk98lin driver for fc6 in rpm format, but it was for the upgraded kernel 2.6.18-1.2849fc6, but my installed kernel is 2.6.18-1.2798fc6.
>
> I downloaded the manufacturer's installation package, but when I try to compile it I keep getting errors saying that there are problems with the kernel headers.
>
> I downloaded and installedthe kernel sources as discussed at:
> http://www.g-loaded.eu/2005/12/14/the-complete-fedora-kernel-headers/
The sk98lin is obsolete, I think. You should try with sky2.
--
Gérard Milmeister
Langackerstrasse 49
CH-8057 Zürich
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
