Yuandan Zhang wrote:
>
>
> lspci does not show this device, from MS Windows side, it shows:
>
> Texas Instruments PCIxx20 Integrated FlashMedia Controllor
> Type: PCMCIA and Flash Memery devices
> Manufacturer: Texas Instrument Inc
> Location PCI Bus 1, device 6, fnuction 3
>
>
Under Linux it probably shows up something like this:
04:06.0 CardBus bridge: Texas Instruments Unknown device 8039
Subsystem: Toshiba America Info Systems Unknown device ff10
Flags: bus master, medium devsel, latency 168, IRQ 18
Memory at dc007000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=04, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 50000000-51fff000 (prefetchable)
Memory window 1: 52000000-53fff000
I/O window 0: 00004400-000044ff
I/O window 1: 00004800-000048ff
16-bit legacy interface ports at 0001
04:06.1 FireWire (IEEE 1394): Texas Instruments Unknown device 803a
(prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Unknown device ff10
Flags: bus master, medium devsel, latency 128, IRQ 16
Memory at dc006000 (32-bit, non-prefetchable) [size=2K]
Memory at dc000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
04:06.2 Mass storage controller: Texas Instruments Unknown device 803b
Subsystem: Toshiba America Info Systems Unknown device ff10
Flags: bus master, medium devsel, latency 128, IRQ 10
Memory at dc004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
04:06.3 Class 0805: Texas Instruments Unknown device 803c (prog-if 01)
Subsystem: Toshiba America Info Systems Unknown device ff10
Flags: bus master, medium devsel, latency 128, IRQ 10
Memory at dc006800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
The chip has 4 functions in one PCI slot as far as the system is
concerned. To make it work, I had to run a script. I added it to
/etc/rc.d/rc.local.
#!/bin/bash
#
# Script to enable SD interface of the TI PCXxx12 interface.
#
# Remove SDHCI and MMC modules, if they are installed.
modprobe -r sdhci
modprobe -r mmc_block
# Change what interface is enabled.
setpci -s 04:06.2 4c.b=02
# Load the SD and MMC modules again.
modprobe sdhci || exit 1
modprobe mmc_block || exit 1
exit 0
What it does is turn off the MMC controller and turn on the SD
controller on the chip. I guess they can not both be on at the same
time. I am not sure what happens if you insert a MMC or a Memory
Stick after doing this, as I only have SD cards. (Well, I have
Compact Flash and Smart Media cards, but they do not fit...)
If your laptop has the chip mapped to a different PCI bus them mine
does, you will have to adjust the setpci command to match. It is bus
4, slot 6 on my Toshiba. (04:06.x)
Mikkel
--
Do not meddle in the affairs of dragons,
for thou art crunchy and taste good with Ketchup!
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
