I have an install of fc5 on a normal ata note book hard drive, in an Ibase FWA7304 (it only has a serial port on vga).
I have managed to get it to work once then it broke and I cant get it to work again..
this is as far as it boots ....
Booting 'Fedora Core (2.6.15-1.2054_FC5)'
root (hd0,0)
Filesystem type is ext2fs, partition type 0x83
kernel /vmlinuz-2.6.15-1.2054_FC5 ro root=LABEL=/ console=tty0 console=ttyS0,19
200n8
[Linux-bzImage, setup=0x1e00, size=0x16eb71]
initrd /initrd-2.6.15-1.2054_FC5.img
[Linux-initrd @ 0x1edff000, 0xe0f81 bytes]
no matter how i reinstall the drive... I even used the hdd from my laptop with a full install of fc5 and it stops at exactly the same place ......
here are my configs
/boot/grub/grub.conf
default=0
#timeout=5
serial --unit=0 --speed=19200 --word=8 --parity=no --stop=1
terminal --timeout=10 serial console
#splashimage=(hd0,0)/grub/splash.xpm.gz
#hiddenmenu
title Fedora Core (2.6.15-1.2054_FC5)
root (hd0,0)
kernel /vmlinuz-2.6.15-1.2054_FC5 ro root=LABEL=/ console=tty0 console=ttyS0,19200n8
initrd /initrd-2.6.15-1.2054_FC5.img
/etc/inittab
id:5:initdefault:
# System initialization.
si::sysinit:/etc/rc.d/rc.sysinit
l0:0:wait:/etc/rc.d/rc 0
l1:1:wait:/etc/rc.d/rc 1
l2:2:wait:/etc/rc.d/rc 2
l3:3:wait:/etc/rc.d/rc 3
l4:4:wait:/etc/rc.d/rc 4
l5:5:wait:/etc/rc.d/rc 5
l6:6:wait:/etc/rc.d/rc 6
# Trap CTRL-ALT-DELETE
ca::ctrlaltdel:/sbin/shutdown -t3 -r now
# When our UPS tells us power has failed, assume we have a few minutes
# of power left. Schedule a shutdown for 2 minutes from now.
# This does, of course, assume you have powerd installed and your
# UPS connected and working correctly.
pf::powerfail:/sbin/shutdown -f -h +2 "Power Failure; System Shutting Down"
# If power was restored before the shutdown kicked in, cancel it.
pr:12345:powerokwait:/sbin/shutdown -c "Power Restored; Shutdown Cancelled"
# Run gettys in standard runlevels
1:2345:respawn:/sbin/mingetty tty1
2:2345:respawn:/sbin/mingetty tty2
3:2345:respawn:/sbin/mingetty tty3
4:2345:respawn:/sbin/mingetty tty4
5:2345:respawn:/sbin/mingetty tty5
6:2345:respawn:/sbin/mingetty tty6
# Run xdm in runlevel 5
x:5:once:/etc/X11/prefdm -nodaemon
s0:12345:respawn:/sbin/agetty ttyS0 19200 vt102
/etc/sysconfig/init
# color => new RH6.0 bootup
# verbose => old-style bootup
# anything else => new style bootup without ANSI colors or positioning
BOOTUP=serial
# Turn on graphical boot
GRAPHICAL=yes
# column to start "[ OK ]" label in
RES_COL=60
# terminal sequence to move to that column. You could change this
# to something like "tput hpa ${RES_COL}" if your terminal supports it
MOVE_TO_COL="echo -en \\033[${RES_COL}G"
# terminal sequence to set color to a 'success' color (currently: green)
SETCOLOR_SUCCESS="echo -en \\033[0;32m"
# terminal sequence to set color to a 'failure' color (currently: red)
SETCOLOR_FAILURE="echo -en \\033[0;31m"
# terminal sequence to set color to a 'warning' color (currently: yellow)
SETCOLOR_WARNING="echo -en \\033[0;33m"
# terminal sequence to reset to the default color.
SETCOLOR_NORMAL="echo -en \\033[0;39m"
# default kernel loglevel on boot (syslog will reset this)
LOGLEVEL=3
# Set to anything other than 'no' to allow hotkey interactive startup...
PROMPT=yes
/etc/sysconfig/kudzu
# Set to anything other than 'no' to force a 'safe' probe on startup.
# 'safe' probe disables:
# - serial port probing
# - DDC monitor probing
# - PS/2 probing
SAFE=yes
/etc/securetty
console
ttyS0
vc/1
vc/2
vc/3
vc/4
vc/5
vc/6
vc/7
vc/8
vc/9
vc/10
vc/11
tty1
tty2
tty3
tty4
tty5
tty6
tty7
tty8
tty9
tty10
tty11
/etc/selinux/config
# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
# enforcing - SELinux security policy is enforced.
# permissive - SELinux prints warnings instead of enforcing.
# disabled - SELinux is fully disabled.
SELINUX=disabled
# SELINUXTYPE= type of policy in use. Possible values are:
# targeted - Only targeted network daemons are protected.
# strict - Full SELinux protection.
SELINUXTYPE=targeted
So what have I missed ?
I used the following howto...
http://bluequartz.org/~oda/docs/serial/index.html
and
http://taosecurity.blogspot.com/2004/06/fedora-core-2-based-soekris-system.html
Many Thanks in advance
--
Gregory Machin
gregory.machin@xxxxxxxxx
www.linuxpro.co.za
-- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
