On Thursday 13 July 2006 04:17, Mikkel L. Ellertson wrote: > Nigel Henry wrote: > > Hi Mikkel. Thanks for explaining how the floppy boot works. From FC2 I > > ran /sbin/grub-install /dev/hda, which was successfull and displayed my > > edited drive map. Rebooted, but still no go, and a "no such disk" when > > trying to boot FC1. Next I booted up Win ME on the basis that at least I > > can see what it says about the card, as I'd used the supplied boot floppy > > to install the drivers on that. According to the device manager there are > > no problems with the card, the only difference from the cards handbook > > was that the handbook said that I would find the card in harddrive > > controllers, but it was actually listed in scsi controllers. Not much > > help there. > > > > Next I venture into the BIOS. In the boot section the dvdrom (hdg) is > > listed last on the list. Also, all 3 harddrives are showing in the BIOS. > > > > Running out of ideas here, but thought I'd try to boot from the dvdrom > > drive, and moved it up to before the harddrive. Then tried Knoppix 5.0, > > but it gave me a boot failed. Not being sure if dvdrom drives can boot > > cdroms I found my only dvdrom for mdk 10.1, and tried that. The output > > from that try was: > > Every DVD drive I have used will boot from a bootable CD as well. > But you may run into a problem with your setup where what you are > booting does not find the DVD drive. > > > Isolinux 1.76 Mandrake Isolinux: > > Disk error 01, AX = 423B, Drive 00 > > Boot failed: press a key to retry... > > Zilch!. Had to hard reset. > > > > I somehow think that this is going to end up going nowhere. I will either > > have to put up with using the floppy for FC1, which Fedora legacy are > > dropping in the next few days, but that's my choice if I want to continue > > using it. Or I can move FC1 to either hda or hdb, which I don't know how > > to do, and just use hde, which is on the IDE PCI adaptor card for backups > > , and data, as it works ok once the system is booted up. > > > > Unless you have any further ideas, I suppose it's a case of "you can't > > win em all" Nigel. > > Well, with the BIOS showing all 3 hard drives, I wonder if the error > message you are getting is actually from the Grub install on hde > after you chain to it. Were you using a different drive > configuration when Grub was installed? If so, you may have to > re-install Grub after booting FC1. But make sure you are installing > it to the MBR on hde, and not overwriting your working Grub install. > Then make sure you are chainloading to the right place. > > Mikkel Hi Mikkel. Sorry for the delay in replying. I've been trying various incantations, then the other machines psu fan stopped (ran out of oil) and tripped the psu's thermal cutout, so I had to spend a bit of time fixing that. Anyway back to the job in hand. I'v actually just got FC1 to boot from the main bootloader in hda, but that is from a kernel entry, not the chainloader. All I get from trying to chainload is a grub prompt. Running /sbin/grub I tried different drives to see if grub> root (hdx,0) would find somewhere to put FC1's bootloader. grub> root (hd2,0) printed the following, after also running grub> setup (hd2). grub> root (hd2,0) Filesystem type is ext2fs, partition type 0x83 grub> setup (hd2) Checking if "/boot/grub/stage1" exists... yes Checking if "/boot/grub/stage2" exists... yes Checking if "/boot/grub/e2fs_stage1_5" exists... yes Running "embed /boot/grub/e2fs_stage1_5 (hd2)"... 15 sectors are embedded. succeeded Running "install /boot/grub/stage1 (hd2) (hd2)1+15 p (hd2,0)/boot/grub/stage2 /boot/grub/grub.conf"... succeeded Done. There's some weird stuff going on here, as (hd2) hdc, is the cdwriter, and when I ran grub> setup (hd2) the writers light was flickering quite a bit, but as you can see from the output above, the bootloader installed ok. Another thing that is a bit weird, is that the kernel entries in grub.conf, apart from the latest from fedora legacy show a strange entry after label=/. Again, as below. LABEL=/ hdc=ide-scsi (perhaps this has something to do with Win ME identifying the IDE PCI adaptor card as a scsi controller) I've never seen that before. Quite what the situation is with the cdwriter now, I don't know. It wasn't showing up in the mobo's BIOS before. Only the cdrom drive (hdd), and the dvdrom (hdg) which I couldn't boot a distro from were there. As I can boot an FC1 kernel from the main bootloader, the harddrive on the IDE PCI adaptor card is obviously accessable, but there is obviously some problem with the BIOS regarding drive ID's. Webmin on FC1 still shows the harddrive on the IDE PCI adaptor card as IDE device E, and yet the mobo's BIOS is identifying this same harddrive as hdc. Anyway, the only problem left now is accessing the Grub menu. I've been back into FC1, and changed the splashimage from (hd4,0) to (hd2,0), but still only get the Grub prompt when trying to chainload to (hd2,0) hdc1, aka hde1. Nigel. > -- > > Do not meddle in the affairs of dragons, > for thou art crunchy and taste good with Ketchup! -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
