Paul Howarth wrote:
On Fri, 2006-05-05 at 05:19 -0700, Roger wrote:
Paul Howarth wrote:
On Thu, 2006-05-04 at 15:13 -0700, Roger wrote:
I have just installed FC4 on a new PC and ran yum update. The yum
update created 94 .rpmnew files. Most of these end with .conf.rpmnew
and the others end with /config/xxxxx.rpmnew.
I understand these to be application configuration files that were not
installed by yum because there may have been local customizations. In
normal circumstances, I should review each .rpmnew file against its
counterpart and determine if if the configuration files can be swapped
by renaming or if the .rpmnew file must first be edited. However, at
least a few of the .rpmnew files seem to be binary and I do not know the
function of each application that has an .rpmnew file.
Because this is a new installation (I have customized my monitor
settings and made a static IP address), a guess is that I just want all
the .rpmnew files installed -- and maybe the existing files renamed to
.rpmold just in case. Is there an installation option that I missed or
is there a cleanup script somewhere to deal with this problem? Would
use of smart (or apt) instead of yum have resulted in fewer problems?
Are you by any chance using x86_64 and are many of these files
associated with packages that you have both .x86_64 and .i386 versions
installed? A common cause of spurious .rpmnew file generation is when
multiple packages own the same config file (as is the case described
above, and also for example /etc/vimrc).
Paul.
Yes, I am using x86_64 and the rpmnew files seem to be consistent with
packages that have .i386 versions. I tried removing a few
(alsa-lib.i386, apr.i386, and SDL.i386) and yum showed no dependencies
and removed them. When I entered a remove command for the x86_64
counterparts, yum showed many dependencies so I did not remove them.
So now the question is why do I have these .386 versions and is it a
good idea to remove them all?
I suspect they were installed by anaconda but other than that I can't
say much; I don't currently have an x86_64 box myself so I'm not up on
the gory details of what's needed and what's not.
I should note that I am trying to install MythTV and after the initial
yum update I added atrpms as a yum repository. atrpms seems to be a bit
flakey (sometimes there and sometimes not), but I think all the rpmnew
files predated my adding atrpms as a repository. I could do a clean
install again to verify that as I am having trouble getting lirc to
install correctly.
What problems are you having exactly?
Paul.
My root problem is my ATI remote does not work, probably because "dmesg
| grep lirc" yields a message 'lirc_dev: no version for "struct_module"
found: kernel tainted'. I think this is because the lirc-devices.noarch
version installed is 0.7.0-1; lirc and lirc-lib are versions 0.8.1.
lirc-kmdl is version 2.6.16 matching my 2.6.16 kernel.
The above is after I removed lirc (and MythTV along with it), and then
reinstalled both. Prior to that I had the same modules installed plus
lirc and lirc-devel versions 0.7.2-1 installed.
I have been following the MythTV installation doc at
http://wilsonet.com/mythtv/fcmyth.php and the ATI Remote doc at
http://www.mythtv.org/wiki/index.php/ATI_Remote_Wonder_II.
-----
Alex, thanks for the note -- I have had no trouble accessing atrpms
today, as I recall my prior problems were limited to early evenings and
weekends.
Roger
--
fedora-list mailing list
fedora-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
