Hello hats,
I posted this message to the Shrike-List a while ago, and suggested to
repost it on this list.
I encountered problems with two of fedora-legacy packages for the
Shrike.
First one was gnome-vfs2 package which crafted incorrectly my GNOME
start menu, hatching everything above 'Run Program...' option. Luckilly
there was a 'rpmsave' config that put things right.
The second is serious, and it's concerned the kernel package,
2.4.20-42.9.legacysmp, as well as the latest one. 2.4.20-43.legacysmp.
I lost automatic power off for the computer. The system just hangs
after 'Power Down' message, instead of shutting off, like it used to.
What was changed? Is there some new unconfigured module I should be
aware?
Below you can take a look at what "dmesg" reports. Here I extracted
what should be interesting:
An unexpected IO-APIC was found. If this kernel release
is less than three months old please report this to
linux-smp@xxxxxxxxxxxxxxx
Should I file bugs on these issues? Thank you for your support.
0
I/O APIC #2 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Kernel command line: ro root=LABEL=/ hdc=ide-scsi hdd=ide-scsi
ide_setup: hdc=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 2405.499 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4797.23 BogoMIPS
Memory: 509928k/523456k available (1497k kernel code, 10964k reserved, 1101k data, 156k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
per-CPU timeslice cutoff: 1463.08 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4810.34 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU1: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
Total of 2 processors activated (9607.57 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-20 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 23.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00178020
....... : arbitration: 00
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@xxxxxxxxxxxxxxx
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 0FF 0F 0 0 0 0 0 1 1 39
02 0FF 0F 0 0 0 0 0 1 1 31
03 0FF 0F 0 0 0 0 0 1 1 41
04 0FF 0F 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 0FF 0F 0 0 0 0 0 1 1 51
07 0FF 0F 0 0 0 0 0 1 1 59
08 0FF 0F 0 0 0 0 0 1 1 61
09 0FF 0F 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 0FF 0F 0 0 0 0 0 1 1 71
0d 0FF 0F 0 0 0 0 0 1 1 79
0e 0FF 0F 0 0 0 0 0 1 1 81
0f 0FF 0F 0 0 0 0 0 1 1 89
10 0FF 0F 1 1 0 1 0 1 1 91
11 0FF 0F 1 1 0 1 0 1 1 99
12 0FF 0F 1 1 0 1 0 1 1 A1
13 0FF 0F 1 1 0 1 0 1 1 A9
14 000 00 1 0 0 0 0 0 0 00
15 0FF 0F 1 1 0 1 0 1 1 B1
16 0FF 0F 1 1 0 1 0 1 1 B9
17 0FF 0F 1 1 0 1 0 1 1 C1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2405.4576 MHz.
..... host bus clock speed is 200.4544 MHz.
cpu: 0, clocks: 2004544, slice: 668181
CPU0<T0:2004544,T1:1336336,D:27,S:668181,C:2004544>
cpu: 1, clocks: 2004544, slice: 668181
CPU1<T0:2004544,T1:668176,D:6,S:668181,C:2004544>
checking TSC synchronization across CPUs: passed.
Starting migration thread for cpu 0
smp_num_cpus: 2.
Starting migration thread for cpu 1
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using IRQ router default [8086/24d0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I9,P0) -> 21
PCI->APIC IRQ transform: (B2,I10,P0) -> 22
PCI->APIC IRQ transform: (B2,I11,P0) -> 23
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: disabled - APM is not SMP safe.
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y120L0, ATA DISK drive
blk: queue c0459580, I/O limit 4095Mb (mask 0xffffffff)
hdc: ASUS DVD-ROM DVD-E616P 0104, ATAPI CD/DVD-ROM drive
hdd: ASUS DRW-1608P, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 146k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 156k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: PCI device 8086:24dd (Intel Corp.)
ehci-hcd 00:1d.7: irq 23, pci mem e084cc00
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 128.
ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 8 ports detected
usb-uhci.c: $Revision: 1.275 $ time 19:17:23 Apr 30 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xd480, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xd880, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0xdc00, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 5
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
Adding Swap: 1052216k swap-space (priority -1)
hub.c: new USB device 00:1d.1-1, assigned address 2
usb-uhci.c: interrupt, status 2, frame# 1056
input0: USB HID v1.10 Keyboard [13ec:000a] on usb3:2.0
input1: USB HID v1.10 Pointer [13ec:000a] on usb3:2.1
usb-uhci.c: ENXIO 84000280, flags 0, urb df747b00, burb df8e3380
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 18 ret -6
usb-uhci.c: ENXIO 84000280, flags 0, urb df8e3280, burb df8e3380
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 18 ret -6
usb-uhci.c: ENXIO 84000280, flags 0, urb df8e3280, burb df8e3380
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 18 ret -6
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usbdevfs: remount parameter error
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
hdd: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: ASUS Model: DVD-E616P Rev: 1.04
Type: CD-ROM ANSI SCSI revision: 02
Vendor: ASUS Model: DRW-1608P Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
IA-32 Microcode Update Driver: v1.11 <tigran@xxxxxxxxxxx>
microcode: CPU0 no microcode found! (sig=f29, pflags=4)
microcode: CPU1 no microcode found! (sig=f29, pflags=4)
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4089 buckets, 32712 max) - 292 bytes per conntrack
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
Model 1002 Rev 00000000 Serial 10021102
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7167 Fri Feb 25 09:08:22 PST 2005
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected an Intel(R) 865G, but could not find the secondary device. Assuming a non-integrated video card.
agpgart: Detected Intel(R) 865G chipset
agpgart: AGP aperture is 64M @ 0xf8000000
hub.c: new USB device 00:1d.1-2, assigned address 3
usb.c: USB device 3 (vend/prod 0x3f0/0xc17) is not claimed by any active driver.
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0C17
printer.c: v0.11: USB Printer Device Class driver
usb.c: USB disconnect on device 00:1d.1-2 address 3
printer.c: usblp0: removed
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
divert: not allocating divert_blk for non-ethernet device ppp0
PPP Deflate Compression module registered
divert: no divert_blk to free, ppp0 not ethernet
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4089 buckets, 32712 max) - 292 bytes per conntrack
--
Igor NestoroviÄ
Home Page: http://jung.ekof.bg.ac.yu
ICQ UIN: 31079000
Attachment:
signature.asc
Description: =?iso-8859-5?Q?=BE=D2=DE?= =?iso-8859-5?Q?_=F8=D5?= =?iso-8859-5?Q?_=D4=D5=DE?= =?iso-8859-5?Q?_=DF=DE=E0=E3=DA=D5?= =?iso-8859-5?Q?_=E1=D0?= =?iso-8859-5?Q?_=D4=D8=D3=D8=E2=D0=DB=DD=D8=DC?= =?iso-8859-5?Q?_=DF=DE=E2=DF=D8=E1=DE=DC?=
-- fedora-legacy-list@xxxxxxxxxx http://www.redhat.com/mailman/listinfo/fedora-legacy-list
