One further bit of information. While brushing up on IP I found this.
Definition: The IP address 192.168.1.0 represents the 192.168.1.x range of addresses where x is between 1 and 255. 192.168.1.0 is a private IP network. It is the default network (but not the default address) for Linksys brand home broadband routers.
192.168.1.0 is not a valid IP address for a network router or other host, and no device on your network should be configured to own this address. Instead, 192.168.1.0 is used in routing tables and by the Internet Protocol internally to identify the 192.168.1.x network as a whole. A router or other network gateway device on these networks is typically installed at 192.168.1.1, and other hosts use higher numbers in the range.
At this point I would recommend changing the routers address.
On Fri, 2009-03-06 at 19:24 +0000, Ray Ward wrote:
Ok lets force the issue.
Create a new network profile using your Ethernet adapter (Probably eth0).
Under network configuration.
IP address 192.168.1.20
Network mask 255.255.255.0
Default Gateway 192.168.1.0
Under DNS set the following
Primary DNS server 192.168.1.0
Save this and activate.
Deactivate any other profiles.
If this does not work I would like you to change the routers address to 192.168.1.1 and change the DHCP range to start from 2.
While 192.168.1.0 is a valid address this could be where the problem is.
So the adapter settings would become.
IP address 192.168.1.20
Network mask 255.255.255.0
Default Gateway 192.168.1.1
Under DNS set the following
Primary DNS server 192.168.1.1
Regards
Ray
On Fri, 2009-03-06 at 13:40 +0530, Gyan PRAKASH wrote:
Please find my answers below………
From: Ray Ward [mailto:rayfward@xxxxxxx]
Sent: Friday, March 06, 2009 1:23 PM
To: Gyan PRAKASH
Cc: fedora-laptop-list@redhat
Subject: RE: F10 installation on Hp laptop(dv5-1210tx)
Here's what you do.
In Vista go to a command prompt and type ipconfig and post it here. 192.168.1.2
In Fedora get a terminal session and type ifconfig and post it here. Command not found – through status of connection ip-comes to be 192.168.1.1
In vista do a nslookup from a command prompt for your favorite web site and check that it returns the correct DNS address. 192.168.1.0
In Fedora do the same from a terminal and check that you get the correct address.
In Vista from a command prompt try pinging the gateway and confirm that you can reach the gateway. YES
In Fedora do the same and confirm that you can reach the gateway. Unreachable host
In vista are you using the WiFi Connection rather than the wired. If so use the wired in both cases so we get the same results. Both are Wired
In both cases the default gateway should be the broadband router and the DNS server will also be the same address as the gateway (This will depend on make and model of the router).
I need this information to catch the problem.
On Thu, 2009-03-05 at 14:09 +0530, Gyan PRAKASH wrote:
Yes I do have a broadband connected to external modem. When I pug-in the LAN cable, it says connected, but nothing works! I verified the ip-address but it’s not the one which I get while running vista.
I need a detail diagnose procedure to catch the problem.
From: Ray Ward [mailto:rayfward@xxxxxxx]
Sent: Thursday, March 05, 2009 1:31 PM
To: Gyan PRAKASH
Cc: fedora-laptop-list@xxxxxxxxxx
Subject: RE: F10 installation on Hp laptop(dv5-1210tx)
Ok.
Do you have a connection such as broadband?
It seems your first problem is getting connected to the internet.
I think you need to setup a wired link to your router first with DHCP enable and see what happens.
There are no security settings so you should just connect. From there we can proceed with the other problems.
Let the updater update everything.
Regards
On Thu, 2009-03-05 at 13:06 +0530, Gyan PRAKASH wrote:
In Add/Remove packages, I’m not able view anything. It says, “unable to load the package view list, it should be done at backend”.
Is it because I’m not able connect to internet, and the list has to be downloaded from http server?
From: Ray Ward [mailto:rayfward@xxxxxxx]
Sent: Wednesday, March 04, 2009 1:26 PM
To: Gyan PRAKASH
Cc: 'Miguel Angel Perez'; fedora-laptop-list@xxxxxxxxxx
Subject: RE: F10 installation on Hp laptop(dv5-1210tx)
Look in Add/remove packages and search for Pulse.
The first item should be this.
Enable pulseaudio support in KDE.
It's unlikely the Nvidia driver would stop sound working.
On Wed, 2009-03-04 at 10:40 +0530, Gyan PRAKASH wrote:
After installing NVIDIA graphics drivers(NVIDIA-Linux-x86_64-180.35-pkg1.run) sound is not working!!!
From: gyan prakash [mailto:gyan.prakash@xxxxxx]
Sent: Tuesday, March 03, 2009 10:35 AM
To: 'Miguel Angel Perez'; 'fedora-laptop-list@xxxxxxxxxx'
Subject: RE: F10 installation on Hp laptop(dv5-1210tx)
Hello,
My laptop multimedia-keys(HP smart keys) works fine in GNOME desktop but doesn’t work with KDE.
Also, Internet is not getting configured. When I plugin the LAN wire, it says connected and the ip address displayed is different to what I see in windows. I have a external modem connected to broadband service provider.
Please provide suggestion to configure the above.
Thanks,
Gyan
From: Miguel Angel Perez [mailto:mangelp@xxxxxxxxx]
Sent: Friday, February 27, 2009 5:48 PM
To: Gyan PRAKASH
Subject: Re: F10 installation on Hp laptop(dv5-1210tx)
Rpmfusion is easy to set up: http://rpmfusion.org/Configuration/
The nvidia-driver is propietary but you are allowed to use it as you own the card, so you sould not care about licensing issues about it. Only philosofical issues for being using a propietary binary thing into your free kernel.
The audio card can be a problem. You first have to identify the chipset and know if alsa supports it, you can start in alsa's web site instructions for new alsa users: http://www.alsa-project.org/main/index.php/Main_Page
Good luck!
2009/2/27 Gyan PRAKASH <gyan.prakash@xxxxxx>
Hey, but am more worried about the Audio card. I tried with F10 KDE live CD but no sound was audible! Also how do I get rpm-fusion usage license?
Is their any alternate method to get sound working on my laptop?
From: Miguel Angel Perez [mailto:mangelp@xxxxxxxxx]
Sent: Friday, February 27, 2009 5:20 PM
To: Gyan PRAKASH
Cc: fedora-laptop-list@xxxxxxxxxx; gyanu2k@xxxxxxxxx
Subject: Re: F10 installation on Hp laptop(dv5-1210tx)
Nvidia graphics will be supported if you use rpm fusion non-free repository, the processor is supported, the touchpad too, the network card too, but the tv tunner the audo codec and the HP MeadiaSmart thing should be check before. The best thing is trying first with a live cd and check that everything works out of the box. With a live cd you should not have proper video aceleration as it will use the default nv driver for your nvidia card until you set up rpmfusion and install nvidia propietary kernel, so don't worry about the video performance.
2009/2/27 Gyan PRAKASH <gyan.prakash@xxxxxx>
Hello,
Hey, did anyone tried Fedora(F10) on HP dv5-1210tx laptop. Following are the specs of my laptop
1. Intel Core 2 Duo 2Ghz
2. NVIDIA GeForce 9200M GS/9600M GT Video/Graphic
3. Synaptics PS/2 Port TouchPad
4. HP Integrated Digital TV Tuner
5. IDT High-Definition Audio CODEC
6. Realtek PCI-E Fast Ethernet NIC
7. HP MediaSmart
Am scared of whether the above mentioned sound/graphics and network hardware’s would work or NOT? Please provide feedback!
Regards,
Gyan
_______________________________________________
Fedora-laptop-list mailing list
Fedora-laptop-list@xxxxxxxxxx
http://www.redhat.com/mailman/listinfo/fedora-laptop-list
--
Regards,
Miguel Ángel Pérez
--
Regards,
Miguel Ángel Pérez
_______________________________________________
Fedora-laptop-list mailing list
Fedora-laptop-list@xxxxxxxxxx
http://www.redhat.com/mailman/listinfo/fedora-laptop-list
|
