Some time ago I bought Rockpro64 board from Pine64. To check how EBBR works, how PCIe works on SBCs, Mali Panfrost driver etc. Board arrived yesterday. I connected serial cable (CB2102 dongles suxx, FT2232HL works fine at 1.5Mbps serial), Ethernet, HDMI and booted. Boot fails each time at same place (whole boot log attached): [ 29.043106] panfrost ff9a0000.gpu: clock rate = 500000000 [ 29.053073] rockchip-vop ff8f0000.vop: Adding to iommu group 1 [ 29.058099] panfrost ff9a0000.gpu: mali-t860 id 0x860 major 0x2 minor 0x0 status 0x0 [ 29.058948] panfrost ff9a0000.gpu: features: 00000000,100e77bf, issues: 00000000,24040400 [ 29.059820] panfrost ff9a0000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 [ 29.061053] panfrost ff9a0000.gpu: shader_present=0xf l2_present=0x1 [ 29.063559] rockchip-vop ff900000.vop: Adding to iommu group 2 [ 29.147966] panfrost ff9a0000.gpu: devfreq_add_device: Unable to find governor for the device [ 29.151244] panfrost ff9a0000.gpu: [drm:panfrost_devfreq_init [panfrost]] *ERROR* Couldn't initialize GPU devfreq [ 29.173499] panfrost ff9a0000.gpu: Fatal error during devfreq init Same effect with F32 and it's 5.6.6 kernel and with rawhide and 5.7-rc4 one. Board boots to login when I blacklist "panfrost" driver with "rd.driver.blacklist=panfrost" kernel argument. Any suggestions what to look at? It's been a while since I did kernel debugging.
Terminal ready
U-Boot TPL 2020.04 (Apr 20 2020 - 00:00:00)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
256B stride
256B stride
lpddr4_set_rate: change freq to 400000000 mhz 0, 1
lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2020.04 (Apr 20 2020 - 00:00:00 +0000)
Trying to boot from MMC1
EFI stub: Booting Linux Kernel...
EFI stub: Using DTB from configuration table
EFI stub: Exiting boot services and installing virtual address map...
Host not halted after 16000 microseconds.
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.7.0-0.rc4.20200508git79dede78c057.1.fc33.aarch64 (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 10.1.1 20200507 (Red Hat 10.1.1-1) (GCC), GNU ld version 2.34-4.fc33) #1 SMP Fri May 8 14:59:03 UTC 2020
[ 0.000000] Machine model: Pine64 RockPro64 v2.1
[ 0.000000] efi: EFI v2.80 by Das U-Boot
[ 0.000000] efi: RTPROP=0xf4f1d040 SMBIOS=0xf4f12000 RNG=0xf4c86040 MEMRESERVE=0xf4c85040
[ 0.000000] efi: seeding entropy pool
[ 0.000000] cma: Reserved 64 MiB at 0x00000000f0000000
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: System description tables not found
[ 0.000000] ACPI: Failed to init ACPI tables
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0xf777a3c0-0xf7790fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000200000-0x000000003fffffff]
[ 0.000000] DMA32 [mem 0x0000000040000000-0x00000000f7ffffff]
[ 0.000000] Normal empty
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000200000-0x00000000f4c85fff]
[ 0.000000] node 0: [mem 0x00000000f4c86000-0x00000000f4c86fff]
[ 0.000000] node 0: [mem 0x00000000f4c87000-0x00000000f4f0bfff]
[ 0.000000] node 0: [mem 0x00000000f4f0c000-0x00000000f4f10fff]
[ 0.000000] node 0: [mem 0x00000000f4f11000-0x00000000f4f11fff]
[ 0.000000] node 0: [mem 0x00000000f4f12000-0x00000000f4f12fff]
[ 0.000000] node 0: [mem 0x00000000f4f13000-0x00000000f4f14fff]
[ 0.000000] node 0: [mem 0x00000000f4f15000-0x00000000f4f1afff]
[ 0.000000] node 0: [mem 0x00000000f4f1b000-0x00000000f4f1cfff]
[ 0.000000] node 0: [mem 0x00000000f4f1d000-0x00000000f4f21fff]
[ 0.000000] node 0: [mem 0x00000000f4f22000-0x00000000f7f2ffff]
[ 0.000000] node 0: [mem 0x00000000f7f30000-0x00000000f7f3ffff]
[ 0.000000] node 0: [mem 0x00000000f7f40000-0x00000000f7ffffff]
[ 0.000000] Zeroed struct page in unavailable ranges: 34 pages
[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] 'bootconfig' found on command line, but no bootconfig found
[ 0.000000] percpu: Embedded 480 pages/cpu s1928216 r8192 d29672 u1966080
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 999432
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=(hd0,msdos2)/vmlinuz-5.7.0-0.rc4.20200508git79dede78c057.1.fc33.aarch64 root=UUID=185c4fe8-fe41-40ce-a662-cec5b2a2a371 ro
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0x3bfff000-0x3ffff000] (64MB)
[ 0.000000] Memory: 3722816K/4061184K available (14396K kernel code, 3474K rwdata, 9900K rodata, 8384K init, 23923K bss, 272832K reserved, 65536K cma-reserved)
[ 0.000000] random: get_random_u64 called from kmem_cache_open+0x34/0x290 with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] kmemleak: Kernel memory leak detector disabled
[ 0.000000] ftrace: allocating 47449 entries in 186 pages
[ 0.000000] ftrace: allocated 186 pages with 5 groups
[ 0.000000] Running RCU self tests
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU lockdep checking is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4096 to nr_cpu_ids=6.
[ 0.000000] rcu: RCU callback double-/use-after-free debug enabled.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 256 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @f5200000 (flat, esz 8, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GICv3: using LPI property table @0x00000000f5190000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000000f51a0000
[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.002766] Console: colour dummy device 80x25
[ 0.017669] printk: console [tty0] enabled
[ 0.018023] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.018256] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.018399] ... MAX_LOCK_DEPTH: 48
[ 0.018545] ... MAX_LOCKDEP_KEYS: 8192
[ 0.018694] ... CLASSHASH_SIZE: 4096
[ 0.018844] ... MAX_LOCKDEP_ENTRIES: 32768
[ 0.018995] ... MAX_LOCKDEP_CHAINS: 65536
[ 0.019146] ... CHAINHASH_SIZE: 32768
[ 0.019296] memory used by lock dependency info: 6813 kB
[ 0.019471] memory used for stack traces: 4224 kB
[ 0.019631] per task-struct memory footprint: 2688 bytes
[ 0.020399] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.020708] pid_max: default: 32768 minimum: 301
[ 0.021708] LSM: Security Framework initializing
[ 0.022043] Yama: becoming mindful.
[ 0.022316] SELinux: Initializing.
[ 0.023546] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.023811] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.039594] rcu: Hierarchical SRCU implementation.
[ 0.047180] Platform MSI: interrupt-controller@fee20000 domain created
[ 0.047986] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.048665] fsl-mc MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.052009] Remapping and enabling EFI services.
[ 0.056982] smp: Bringing up secondary CPUs ...
[ 0.062986] Detected VIPT I-cache on CPU1
[ 0.063044] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
[ 0.063286] GICv3: CPU1: using allocated LPI pending table @0x00000000f51b0000
[ 0.063399] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.069505] Detected VIPT I-cache on CPU2
[ 0.069559] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
[ 0.069814] GICv3: CPU2: using allocated LPI pending table @0x00000000f51c0000
[ 0.069906] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.075598] Detected VIPT I-cache on CPU3
[ 0.075653] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
[ 0.075903] GICv3: CPU3: using allocated LPI pending table @0x00000000f51d0000
[ 0.075991] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.081641] CPU features: detected: EL2 vector hardening
[ 0.081723] CPU features: detected: ARM erratum 1319367
[ 0.081736] Detected PIPT I-cache on CPU4
[ 0.081782] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
[ 0.081952] GICv3: CPU4: using allocated LPI pending table @0x00000000f51e0000
[ 0.082017] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
[ 0.087468] Detected PIPT I-cache on CPU5
[ 0.087505] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
[ 0.087661] GICv3: CPU5: using allocated LPI pending table @0x00000000f51f0000
[ 0.087713] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
[ 0.088512] smp: Brought up 1 node, 6 CPUs
[ 0.092708] SMP: Total of 6 processors activated.
[ 0.092882] CPU features: detected: 32-bit EL0 Support
[ 0.093065] CPU features: detected: CRC32 instructions
[ 0.094533] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.173823] CPU: All CPU(s) started at EL2
[ 0.174358] alternatives: patching kernel code
[ 0.184249] devtmpfs: initialized
[ 0.280880] Registered cp15_barrier emulation handler
[ 0.281031] Registered setend emulation handler
[ 0.281177] KASLR enabled
[ 0.315852] DMA-API: preallocated 65536 debug entries
[ 0.315975] DMA-API: debugging enabled by kernel config
[ 0.316089] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.316305] futex hash table entries: 2048 (order: 6, 262144 bytes, linear)
[ 0.372720] pinctrl core: initialized pinctrl subsystem
[ 0.377311]
[ 0.377370] *************************************************************
[ 0.377496] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.377621] ** **
[ 0.377746] ** IOMMU DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL **
[ 0.377870] ** **
[ 0.377994] ** This means that this kernel is built to expose internal **
[ 0.378118] ** IOMMU data structures, which may compromise security on **
[ 0.378242] ** your system. **
[ 0.378366] ** **
[ 0.378551] ** If you see this message and you are not debugging the **
[ 0.378679] ** kernel, report this immediately to your vendor! **
[ 0.378803] ** **
[ 0.378927] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.379050] *************************************************************
[ 0.380122] thermal_sys: Registered thermal governor 'fair_share'
[ 0.380135] thermal_sys: Registered thermal governor 'step_wise'
[ 0.380264] thermal_sys: Registered thermal governor 'user_space'
[ 0.383514] SMBIOS 3.0 present.
[ 0.383712] DMI: pine64 rockpro64_rk3399/rockpro64_rk3399, BIOS 2020.04 04/20/2020
[ 0.386516] NET: Registered protocol family 16
[ 0.433346] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.433534] audit: initializing netlink subsys (disabled)
[ 0.434743] audit: type=2000 audit(0.430:1): state=initialized audit_enabled=0 res=1
[ 0.440800] cpuidle: using governor menu
[ 0.441672] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.442507] ASID allocator initialised with 32768 entries
[ 0.445076] Serial: AMBA PL011 UART driver
[ 0.719592] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.719738] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.719868] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.719997] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 1.244708] cryptomgr_test (53) used greatest stack depth: 12656 bytes left
[ 1.247674] kworker/u12:0 (55) used greatest stack depth: 12400 bytes left
[ 1.454509] cryptd: max_cpu_qlen set to 1000
[ 1.553076] alg: No test for 842 (842-generic)
[ 1.555677] alg: No test for 842 (842-scomp)
[ 1.567946] cryptomgr_test (103) used greatest stack depth: 12144 bytes left
[ 1.643872] fbcon: Taking over console
[ 1.644495] ACPI: Interpreter disabled.
[ 1.656265] vcc3v3_pcie: supplied by vcc12v_dcin
[ 1.667888] vcc5v0_sys: supplied by vcc12v_dcin
[ 1.670962] vcc5v0_usb: supplied by vcc12v_dcin
[ 1.673093] vcc3v3_sys: supplied by vcc5v0_sys
[ 1.677005] iommu: Default domain type: Translated
[ 1.689823] vgaarb: loaded
[ 1.693183] SCSI subsystem initialized
[ 1.695627] usbcore: registered new interface driver usbfs
[ 1.696002] usbcore: registered new interface driver hub
[ 1.696649] usbcore: registered new device driver usb
[ 1.698289] pps_core: LinuxPPS API ver. 1 registered
[ 1.698396] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx>
[ 1.698625] PTP clock support registered
[ 1.699916] EDAC MC: Ver: 3.0.0
[ 1.710261] NetLabel: Initializing
[ 1.710355] NetLabel: domain hash size = 128
[ 1.710448] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 1.710873] NetLabel: unlabeled traffic allowed by default
[ 1.713923] clocksource: Switched to clocksource arch_sys_counter
[ 2.332862] VFS: Disk quotas dquot_6.6.0
[ 2.333260] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.336560] pnp: PnP ACPI: disabled
[ 2.388511] NET: Registered protocol family 2
[ 2.391930] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 180224 bytes, linear)
[ 2.392765] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 2.395916] TCP bind hash table entries: 32768 (order: 9, 2621440 bytes, linear)
[ 2.405780] TCP: Hash tables configured (established 32768 bind 32768)
[ 2.408237] UDP hash table entries: 2048 (order: 6, 393216 bytes, linear)
[ 2.409860] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes, linear)
[ 2.412727] NET: Registered protocol family 1
[ 2.412906] NET: Registered protocol family 44
[ 2.413026] PCI: CLS 0 bytes, default 64
[ 2.414787] Trying to unpack rootfs image as initramfs...
[ 8.256529] Freeing initrd memory: 54648K
[ 8.260472] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 8.262145] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 8.263590] kvm [1]: IPA Size Limit: 40bits
[ 8.290835] kvm [1]: vgic-v2@fff20000
[ 8.290998] kvm [1]: GIC system register CPU interface enabled
[ 8.292027] kvm [1]: vgic interrupt IRQ10
[ 8.293091] kvm [1]: Hyp mode initialized successfully
[ 10.935863] Initialise system trusted keyrings
[ 10.936507] Key type blacklist registered
[ 10.937450] workingset: timestamp_bits=37 max_order=20 bucket_order=0
[ 11.004055] zbud: loaded
[ 11.078762] NET: Registered protocol family 38
[ 11.078998] Key type asymmetric registered
[ 11.079151] Asymmetric key parser 'x509' registered
[ 11.079426] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 11.080657] io scheduler mq-deadline registered
[ 11.080763] io scheduler kyber registered
[ 11.081758] io scheduler bfq registered
[ 11.088917] atomic64_test: passed
[ 11.198124] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 11.265722] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 38, base_baud = 1500000) is a 16550A
[ 11.267183] serial serial0: tty port ttyS0 registered
[ 11.270422] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 39, base_baud = 1500000) is a 16550A
[ 11.399828] printk: console [ttyS2] enabled
[ 11.408490] msm_serial: driver initialized
[ 11.422177] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 11.433438] libphy: Fixed MDIO Bus: probed
[ 11.436681] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.437449] ehci-pci: EHCI PCI platform driver
[ 11.438653] usbcore: registered new interface driver usbserial_generic
[ 11.439575] usbserial: USB Serial support registered for generic
[ 11.441496] mousedev: PS/2 mouse device common for all mice
[ 11.455846] rk808 0-001b: chip id: 0x0
[ 11.468953] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 11.469761] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 11.470667] DCDC_REG1: supplied by vcc5v0_sys
[ 11.474375] vcc5v0_host: supplied by vcc5v0_usb
[ 11.475336] vcc5v0_typec: supplied by vcc5v0_usb
[ 11.476479] DCDC_REG2: supplied by vcc5v0_sys
[ 11.479256] DCDC_REG3: supplied by vcc5v0_sys
[ 11.481517] DCDC_REG4: supplied by vcc5v0_sys
[ 11.484457] LDO_REG1: supplied by vcc5v0_sys
[ 11.488157] LDO_REG2: supplied by vcc5v0_sys
[ 11.491443] LDO_REG3: supplied by vcc5v0_sys
[ 11.495082] LDO_REG4: supplied by vcc5v0_sys
[ 11.498551] LDO_REG5: supplied by vcc5v0_sys
[ 11.501645] LDO_REG6: supplied by vcc5v0_sys
[ 11.505289] LDO_REG7: supplied by vcc5v0_sys
[ 11.508527] LDO_REG8: supplied by vcc5v0_sys
[ 11.511984] SWITCH_REG1: supplied by vcc3v3_sys
[ 11.514360] SWITCH_REG2: supplied by vcc3v3_sys
[ 11.520161] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[ 11.520986] fan53555-reg: supplied by vcc5v0_sys
[ 11.525537] vcc1v8_s3: supplied by vcc_1v8
[ 11.528760] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[ 11.529572] fan53555-reg: supplied by vcc5v0_sys
[ 11.545643] device-mapper: uevent: version 1.0.3
[ 11.548297] device-mapper: ioctl: 4.42.0-ioctl (2020-02-27) initialised: dm-devel@xxxxxxxxxx
[ 11.561228] ledtrig-cpu: registered to indicate activity on CPUs
[ 11.569108] hid: raw HID events driver (C) Jiri Kosina
[ 11.570603] usbcore: registered new interface driver usbhid
[ 11.571202] usbhid: USB HID core driver
[ 11.580842] drop_monitor: Initializing network drop monitor service
[ 11.582150] Initializing XFRM netlink socket
[ 11.585950] NET: Registered protocol family 10
[ 11.805904] Segment Routing with IPv6
[ 11.806331] RPL Segment Routing with IPv6
[ 11.806945] mip6: Mobile IPv6
[ 11.807299] NET: Registered protocol family 17
[ 11.811966] registered taskstats version 1
[ 11.812653] Loading compiled-in X.509 certificates
[ 12.014718] Loaded X.509 cert 'Fedora kernel signing key: 55a62b57e03d71686d8cc11719b5805f74d36de6'
[ 12.017433] zswap: loaded using pool lzo/zbud
[ 12.022955] Key type ._fscrypt registered
[ 12.023426] Key type .fscrypt registered
[ 12.024085] Key type fscrypt-provisioning registered
[ 12.143551] Key type big_key registered
[ 12.996235] Key type encrypted registered
[ 12.996984] ima: No TPM chip found, activating TPM-bypass!
[ 12.997701] ima: Allocated hash algorithm: sha256
[ 12.998342] ima: No architecture policies found
[ 13.284042] random: fast init done
[ 13.375449] dw-apb-uart ff1a0000.serial: forbid DMA for kernel console
[ 13.436921] Freeing unused kernel memory: 8384K
[ 13.513863] Checked W+X mappings: passed, no W+X pages found
[ 13.514628] rodata_test: all tests were successful
[ 13.515180] Run /init as init process
[ 13.601951] systemd[1]: System time before build time, advancing clock.
[ 13.685784] systemd[1]: systemd v245.5-2.fc33 running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 13.699275] systemd[1]: Detected architecture arm64.
[ 13.699888] systemd[1]: Running in initial RAM disk.
Welcome to Fedora 33 (Rawhide Prerelease) dracut-050-26.git20200316.fc33 (Initramfs)!
[ 13.746135] systemd[1]: No hostname configured.
[ 13.746885] systemd[1]: Set hostname to <localhost>.
[ 13.748343] random: systemd: uninitialized urandom read (16 bytes read)
[ 13.749316] systemd[1]: Initializing machine ID from random generator.
[ 14.989533] random: systemd: uninitialized urandom read (16 bytes read)
[ 14.990410] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 14.994800] random: systemd: uninitialized urandom read (16 bytes read)
[ 14.995680] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 14.998624] random: systemd: uninitialized urandom read (16 bytes read)
[ 14.999515] systemd[1]: Reached target Timers.
[ OK ] Reached target Timers.
[ 15.005720] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 15.011698] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 15.017601] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 15.023493] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 15.028282] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 15.031108] systemd[1]: Reached target Sockets.
[ OK ] Reached target Sockets.
[ 15.080145] systemd[1]: Starting Create list of static device nodes for the current kernel...
Starting Create list of st…odes for the current kernel...
[ 15.126877] systemd[1]: Started Hardware RNG Entropy Gatherer Daemon.
[ OK ] Started Hardware RNG Entropy Gatherer Daemon.
[ 15.202731] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 15.237566] systemd[1]: Condition check resulted in Load Kernel Modules being skipped.
[ 15.260836] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 15.297043] systemd[1]: Starting Setup Virtual Console...
Starting Setup Virtual Console...
[ 15.355144] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ OK ] Finished Create list of st… nodes for the current kernel.
[ 15.423070] systemd[1]: Starting Create Static Device Nodes in /dev...
Starting Create Static Device Nodes in /dev...
[ 15.457922] systemd[1]: Finished Setup Virtual Console.
[ OK ] Finished Setup Virtual Console.
[ 15.513868] systemd[1]: Finished Apply Kernel Variables.
[ OK ] Finished Apply Kernel Variables.
[ 15.592794] systemd[1]: Starting dracut ask for additional cmdline parameters...
Starting dracut ask for additional cmdline parameters...
[ 15.625456] systemd[1]: Finished Create Static Device Nodes in /dev.
[ OK ] Finished Create Static Device Nodes in /dev.
[ 15.846946] systemd[1]: Finished dracut ask for additional cmdline parameters.
[ OK ] Finished dracut ask for additional cmdline parameters.
[ 15.880780] systemd[1]: Starting dracut cmdline hook...
Starting dracut cmdline hook...
[ 16.311369] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ 16.336074] audit: type=1130 audit(1587127034.730:2): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-journald comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ OK ] Finished dracut cmdline hook.
[ 17.315093] audit: type=1130 audit(1587127035.710:3): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-cmdline comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
Starting dracut pre-udev hook...
[ 17.732491] raid6: skip pq benchmark and using algorithm neonx8
[ 17.733144] raid6: using neon recovery algorithm
[ 17.750371] xor: measuring software checksum speed
[ 17.843916] 8regs : 2386.800 MB/sec
[ 17.943915] 32regs : 2732.400 MB/sec
[ 18.043914] arm64_neon: 2402.000 MB/sec
[ 18.044377] xor: using function: 32regs (2732.400 MB/sec)
[ 18.624653] Btrfs loaded, crc32c=crc32c-generic
[ 18.703547] alua: device handler registered
[ 18.763860] emc: device handler registered
[ 18.827110] rdac: device handler registered
[ OK ] Finished dracut pre-udev hook.
[ 19.135458] audit: type=1130 audit(1587127037.530:4): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-udev comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 19.150301] audit: type=1334 audit(1587127037.540:5): prog-id=6 op=LOAD
[ 19.151640] audit: type=1334 audit(1587127037.540:6): prog-id=7 op=LOAD
Starting udev Kernel Device Manager...
[ OK ] Started udev Kernel Device Manager.
[ 20.195115] audit: type=1130 audit(1587127038.590:7): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-udevd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
Starting dracut pre-trigger hook...
[ OK ] Finished dracut pre-trigger hook.
[ 21.715111] audit: type=1130 audit(1587127040.110:8): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
Starting udev Coldplug all Devices...
[ OK ] Finished udev Coldplug all Devices.
[ 24.910443] audit: type=1130 audit(1587127043.300:9): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-udev-trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
Mounting Kernel Configuration File System...
Starting dracut initqueue hook...
Starting Show Plymouth Boot Screen...
Starting udev Wait for Complete Device Initialization...
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started Show Plymouth Boot Screen.
[ 25.304512] audit: type=1130 audit(1587127043.700:10): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=plymouth-start comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ OK ] Started Forward Password R…s to Plymouth Directory Watch.
[ OK ] Reached target Local Encrypted Volumes.
[ OK ] Reached target Paths.
[ 25.518841] Synopsys Designware Multimedia Card Interface Driver
[ 25.745439] dwmmc_rockchip fe310000.mmc: IDMAC supports 32-bit address mode.
[ 25.746574] dwmmc_rockchip fe310000.mmc: Using internal DMA controller.
[ 25.747297] dwmmc_rockchip fe310000.mmc: Version ID is 270a
[ 25.748131] dwmmc_rockchip fe310000.mmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
[ 25.749968] dwmmc_rockchip fe310000.mmc: allocated mmc-pwrseq
[ 25.750606] mmc_host mmc0: card is non-removable.
[ 25.868388] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 25.889464] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
[ 25.890321] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
[ 25.891078] dwmmc_rockchip fe320000.mmc: Version ID is 270a
[ 25.892006] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 29,32 bit host data width,256 deep fifo
[ 25.915723] dwmmc_rockchip fe320000.mmc: Got CD GPIO
[ 25.927913] mmc_host mmc0: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[ 25.955236] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 25.974367] mmc_host mmc0: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[ 26.029516] ehci-platform: EHCI generic platform driver
[ 26.030760] mmc_host mmc0: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
[ 26.040967] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 26.042687] mmc1: new high speed SD card at address 6939
[ 26.166249] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 26.168155] pwm-regulator: supplied by regulator-dummy
[ 26.229472] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 26.230425] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[ 26.253677] ohci-platform: OHCI generic platform driver
[ 26.363416] sdhci: Secure Digital Host Controller Interface driver
[ 26.364215] sdhci: Copyright(c) Pierre Ossman
[ 26.378838] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 26.379668] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 26.688018] sdhci-pltfm: SDHCI platform and OF driver helper
[ 26.870865] sdhci-arasan fe330000.sdhci: No phy for arasan,sdhci-5.1.
[ 27.190744] mmc2: CQHCI version 5.10
[ 27.244171] mmc2: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[ 27.383042] ehci-platform fe380000.usb: EHCI Host Controller
[ 27.394694] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
[ 27.396943] ehci-platform fe380000.usb: irq 31, io mem 0xfe380000
[ 27.424213] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[ 27.429909] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.07
[ 27.431077] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 27.431979] usb usb1: Product: EHCI Host Controller
[ 27.432605] usb usb1: Manufacturer: Linux 5.7.0-0.rc4.20200508git79dede78c057.1.fc33.aarch64 ehci_hcd
[ 27.433733] usb usb1: SerialNumber: fe380000.usb
[ 27.454084] rk808-rtc rk808-rtc: registered as rtc0
[ 27.464884] hub 1-0:1.0: USB hub found
[ 27.466556] hub 1-0:1.0: 1 port detected
[ 27.494779] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[ 27.514315] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 2
[ 27.516089] rk808-rtc rk808-rtc: setting system clock to 2020-05-13T06:42:53 UTC (1589352173)
[ 27.516374] ohci-platform fe3a0000.usb: irq 32, io mem 0xfe3a0000
[ 27.590191] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.07
[ 27.591242] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 27.592144] usb usb2: Product: Generic Platform OHCI controller
[ 27.592890] usb usb2: Manufacturer: Linux 5.7.0-0.rc4.20200508git79dede78c057.1.fc33.aarch64 ohci_hcd
[ 27.594202] usb usb2: SerialNumber: fe3a0000.usb
[ 27.606299] hub 2-0:1.0: USB hub found
[ 27.607204] hub 2-0:1.0: 1 port detected
[ 27.620231] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[ 27.623384] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 3
[ 27.625480] ohci-platform fe3e0000.usb: irq 34, io mem 0xfe3e0000
[ 27.699812] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.07
[ 27.700862] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 27.701765] usb usb3: Product: Generic Platform OHCI controller
[ 27.702510] usb usb3: Manufacturer: Linux 5.7.0-0.rc4.20200508git79dede78c057.1.fc33.aarch64 ohci_hcd
[ 27.703639] usb usb3: SerialNumber: fe3e0000.usb
[ 27.716211] hub 3-0:1.0: USB hub found
[ 27.717038] hub 3-0:1.0: 1 port detected
[ 27.726039] ehci-platform fe3c0000.usb: EHCI Host Controller
[ 27.728482] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 4
[ 27.730300] ehci-platform fe3c0000.usb: irq 33, io mem 0xfe3c0000
[ 27.754155] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[ 27.757804] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.07
[ 27.758846] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 27.759748] usb usb4: Product: EHCI Host Controller
[ 27.760372] usb usb4: Manufacturer: Linux 5.7.0-0.rc4.20200508git79dede78c057.1.fc33.aarch64 ehci_hcd
[ 27.761501] usb usb4: SerialNumber: fe3c0000.usb
[ 27.776286] hub 4-0:1.0: USB hub found
[ 27.777416] hub 4-0:1.0: 1 port detected
[ 28.429221] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 28.788741] random: crng init done
[ 28.789145] random: 6 urandom warning(s) missed due to ratelimiting
[ 29.043106] panfrost ff9a0000.gpu: clock rate = 500000000
[ 29.053073] rockchip-vop ff8f0000.vop: Adding to iommu group 1
[ 29.058099] panfrost ff9a0000.gpu: mali-t860 id 0x860 major 0x2 minor 0x0 status 0x0
[ 29.058948] panfrost ff9a0000.gpu: features: 00000000,100e77bf, issues: 00000000,24040400
[ 29.059820] panfrost ff9a0000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7
[ 29.061053] panfrost ff9a0000.gpu: shader_present=0xf l2_present=0x1
[ 29.063559] rockchip-vop ff900000.vop: Adding to iommu group 2
[ 29.147966] panfrost ff9a0000.gpu: devfreq_add_device: Unable to find governor for the device
[ 29.151244] panfrost ff9a0000.gpu: [drm:panfrost_devfreq_init [panfrost]] *ERROR* Couldn't initialize GPU devfreq
[ 29.173499] panfrost ff9a0000.gpu: Fatal error during devfreq init
_______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/ List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
