Hi Fred, Am 03.04.20 um 13:10 schrieb Fred van Zwieten: > I haven't retried it yet, but I do have some extra info on my previous > (and failed) attempt: > > I used arm-image-installer as the tool. As it does not yet have a rpi4 > target, I used the rpi3 value. It does boot, but, like I said, it > hangs in a later stage. I will provide screenshots when I am able to > test again. > > This is the (relevant) output from /proc/cpuinfo: > Hardware : BCM2835 > Revision : c03111 > Serial : 1000000094b1358a > Model : Raspberry Pi 4 Model B Rev 1.1 this should work with Linux 5.6. So i don't have an idea what's the problem here. Rev 1.2 needs recent changes to sdhci-iproc and the devicetree. Best regards Stefan > > - Fred > > On Fri, Apr 3, 2020 at 12:25 PM Andreas Reschke <arm_ml@xxxxxxxxxxx > <mailto:arm_ml@xxxxxxxxxxx>> wrote: > > Hello Dirk, > > I've tried it with balenaEtcher: It works !! > > Thank you for that tip !! > > Andreas > > PS: I dind't know why it not works with xzcat and dd but now I have a > working method. > > Am 03.04.20 um 10:23 schrieb Dirk Streubel: > >> Hello together, > >> > >> Hello Dirk > >> > >> how did you you install > Fedora-Minimal-32_Beta-1.2.aarch64.raw.xz on SD-Card? > >> > >> Just xzcat Fedora-Minimal-32_Beta-1.2.aarch64.raw.xz | dd > of=/dev/sdc status=progress bs=4M > >> > >> didn't work for me. All I get is a dracut shell > >> > >> > >> Thanks > >> > >> Andreas > > Hello Andreas, > > > > yes, i installed the two Version yesterday on a 64 GB SD Card. > > > > Image has been unpacked with all necessary tools. > > > > For installation on the SD Card i use balenaEtcher. That Program > works fine here. > > > > Dirk > > > > > > > > > > > >> _______________________________________________ > >> arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx > <mailto:arm@xxxxxxxxxxxxxxxxxxxxxxx> > >> To unsubscribe send an email to > arm-leave@xxxxxxxxxxxxxxxxxxxxxxx > <mailto:arm-leave@xxxxxxxxxxxxxxxxxxxxxxx> > >> Fedora Code of Conduct: > https://docs.fedoraproject.org/en-US/project/code-of-conduct/ > >> List Guidelines: > https://fedoraproject.org/wiki/Mailing_list_guidelines > >> List Archives: > https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx > > _______________________________________________ > > arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx > <mailto:arm@xxxxxxxxxxxxxxxxxxxxxxx> > > To unsubscribe send an email to > arm-leave@xxxxxxxxxxxxxxxxxxxxxxx > <mailto:arm-leave@xxxxxxxxxxxxxxxxxxxxxxx> > > Fedora Code of Conduct: > https://docs.fedoraproject.org/en-US/project/code-of-conduct/ > > List Guidelines: > https://fedoraproject.org/wiki/Mailing_list_guidelines > > List Archives: > https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx > _______________________________________________ > arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx > <mailto:arm@xxxxxxxxxxxxxxxxxxxxxxx> > To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx > <mailto:arm-leave@xxxxxxxxxxxxxxxxxxxxxxx> > Fedora Code of Conduct: > https://docs.fedoraproject.org/en-US/project/code-of-conduct/ > List Guidelines: > https://fedoraproject.org/wiki/Mailing_list_guidelines > List Archives: > https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx > > > _______________________________________________ > arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx > To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx > Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/ > List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines > List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/ List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
