On 3/4/20 8:34 AM, Peter Robinson wrote:
Thanks Paul. I just tried Fedora-Workstation-32-20200225.n.0.aarch64.raw.xz on my RPi4 but it behaves the same as I previously reported. There is a 5 minute pause after the eth0 link becomes ready and I then wind up in the dracut emergency shell.
That's two different an unrelated problems. Is the pause with ethernet
before the grub2 prompt?
No - the pause is in the kernel. In an earlier email in this chain, I attached a file "session.log". Here is part of that file - note that the eth0 link comes up at around the 28 second mark. Then there is a 5 minute pause where nothing appears to be happening, and then at the 321 second mark, dracut starts printing timeout messages.
I don't read attachments, much less compressed globs of information,
sorry it takes too much time to search for a needle in a haystack.
Ok - I provided the attachment because people often want the full details rather than a summary. Next time I'll be sure to provide both.
[ 23.467681] raspberrypi-firmware soc:firmware: Request 0x00028001 returned status 0x00000000
[ 23.969125] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[ 23.986485] bcmgenet fd580000.ethernet eth0: Link is Down
[ 27.394605] systemd-udevd (515) used greatest stack depth: 11696 bytes left
[ 28.172043] bcmgenet fd580000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 28.186922] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 28.241941] NetworkManager (549) used greatest stack depth: 10272 bytes left
[ 234.092146] random: crng init done
[ 234.101385] random: 6 urandom warning(s) missed due to ratelimiting
[ 321.541094] dracut-initqueue[522]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 322.921646] dracut-initqueue[522]: Warning: dracut-initqueue timeout - starting timeout scripts
The "Warning: dracut-initqueue timeout" messages repeat for a quite a while, then at the 466 second mark we get the following:
[ 464.979853] dracut-initqueue[522]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 466.181960] dracut-initqueue[522]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 466.183175] dracut-initqueue[522]: Warning: Could not boot.
Starting Setup Virtual Console...
[ OK ] Started Setup Virtual Console.
[ 466.475450] audit: type=1130 audit(1580894910.719:14): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-vconsole-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ 466.475689] audit: type=1131 audit(1580894910.719:15): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-vconsole-setup comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
Starting Dracut Emergency Shell...
[ 466.661153] audit: type=1131 audit(1580894910.899:16): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=plymouth-start comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
Warning: /dev/disk/by-uuid/369ee56a-5038-4040-b16e-f127f8a81ba0 does not exist
What storage/medium are you booting off? Unless it's a network style
of storage it's actually unlikely to be an issue here with the network
side of things. More likely storage.
I have a 4 GB RPi4 with an SD card. I think you are correct that it looks more like a storage issue.
Also what rev of the RPi4 hardware do you have? If it's one of the
refresh versions there may be an issue around a firmware <-> kernel
interaction. I should have a new rev 2Gb version in the next day or
so, there's a proposed patch under review upstream but I think it
might need a newer firmware as well. I'll be testing once I have all
the pieces available.
Great. Thanks for checking. Here is the hardware data for my board:
Hardware : BCM2835
Revision : c03112
Serial : 100000004463a5a7
Model : Raspberry Pi 4 Model B Rev 1.2
Based on the revision-codes page [1], this would be the latest revision of the 4 GB RPi4 board.
Steve
[1] https://www.raspberrypi.org/documentation/hardware/raspberrypi/revision-codes/README.md
_______________________________________________
arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/
List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
