On Thu, Aug 9, 2018 at 2:40 AM, Jonathan Vaughn <jonathan@xxxxxxxxxxxxx> wrote: > I see a few months ago in the mailing list that support was brought up (in > the context of F27) and it was mentioned that improving support for > Rockchips devices in general was intended for F28. Yes, I did intend on doing that, I ran into a number of problems and also purely just ran out of time. > It doesn't appear that fedora-arm-installer currently supports the Rock64 > board as far as I can tell. That is correct and the Rock64 particularly is different to the Rockchips support above. The Rock64 device is not supported in upstream u-boot which is what we ship and for a device to be classified as fully supported by Fedora so even when the improvement in Rockchips support lands (which I'm hoping I will finish off in F-29, assistance would help) it's currently unlikely the Rock64 will be in that list. > I'm trying to figure out how to add support by adding to > /usr/share/arm-image-installer/boards.d and socs.d, as well as solving the > lack of appropriate uboot in /usr/share/uboot for Rock64. That's two different problems and there's a bunch of other stuff that is actually in there. > I flashed (and tested successfully) a community built Debian Stretch image > and by comparing it's partition layout and some information from OpenSUSE I > can guess at what some of it should be, but I'm not entirely sure how to > make the appropriate files in socs.d, boards.d, and what all is needed in > uboot ... Most of what you have below is interesting but most probably won't going into a-i-i, we don't currently and personally I really not sure i want to go the route of moving around partitions and changing partitioning schemes on the fly there. > Debian Stretch image that boots : > https://github.com/ayufan-rock64/linux-build/releases/download/0.7.8/stretch-minimal-rock64-0.7.8-1061-arm64.img.xz > U-boot used in the above build : > https://github.com/ayufan-rock64/linux-u-boot > OpenSUSE info : https://en.opensuse.org/HCL:Rock64 > > working stretch partition layout : > # gdisk -l /dev/sdc > GPT fdisk (gdisk) version 1.0.4 > > Partition table scan: > MBR: protective > BSD: not present > APM: not present > GPT: present > > Found valid GPT with protective MBR; using GPT. > Disk /dev/sdc: 62333952 sectors, 29.7 GiB > Model: Storage Device > Sector size (logical/physical): 512/512 bytes > Disk identifier (GUID): 9CFDF7D8-766C-43DE-9354-57097D428E8F > Partition table holds up to 128 entries > Main partition table begins at sector 2 and ends at sector 33 > First usable sector is 34, last usable sector is 62333918 > Partitions will be aligned on 64-sector boundaries > Total free space is 30 sectors (15.0 KiB) > > Number Start (sector) End (sector) Size Code Name > 1 64 8063 3.9 MiB 8300 loader1 > 2 8064 8191 64.0 KiB 8300 reserved1 > 3 8192 16383 4.0 MiB 8300 reserved2 > 4 16384 24575 4.0 MiB 8300 loader2 > 5 24576 32767 4.0 MiB 8300 atf > 6 32768 262143 112.0 MiB 0700 boot > 7 262144 62333918 29.6 GiB 8300 root > > loader1 (partition 1) is the SPL, loader2 (partition 4) is the U-Boot. atf > (partition 5) per OpenSUSE is apparently some kind of "trust" image. ATF is Arm Trusted Firmware, it's a requirement of ARMv8 / aarch64. It's a core part of the ARM architecture and handles a number of things including the PSCI which is what handles things such as secondary CPU startup etc. > The reserved partitions (partitions 2 and 3) seem to just be all nulls. > > The boot partition (partition 6) has extlinux/extlinux.conf apparently as > well as 'System Volume Information' (guessing that the origin of that > partition was built on Windows), and partition 7 is of course regular old > Linux filesystem. Being Debian I very much doubt that TBH > I'm not sure how fedora-arm-installer decides to partition things, it wasn't It doesn't, only thing it does related to partitions is to optionally grow the root partitions out to the full size of the destination storage. > obvious from socs.d/boards.d, so I'm not sure how to ensure that when > creating the soc/board scripts that the correct layout is maintained. From > glancing at the source code for fedora-arm-installer it seems like it just > extracts the image onto the media and assumes the layout based on what was > in the image, which might present a problem if the unified AArch64 image has > only 3 partitions? Unless it would be expected that Fedora would have it's > own build of uboot that would ensure things didn't need all those other > partitions ? > > Anyways, I'm happy to either figure this out on my own if you can point me > in the right direction or if you already have some WIP that needs a > volunteer to test it, to do be your guinea pig. So all the of the above is interesting but I'm not sure we actually need to put all the bits into a series of partitions. Generally a lot of the above appears to be based upon the way Android does this stuff. Rockchips actually some really good docs on their boot process, a few bits are a little out of date based on improvements in upstream U-Boot but it's a very useful starting point: http://opensource.rock-chips.com/wiki_Boot_option >From there we should be able to dd out the U-Boot/ATF stack to an offset and it should just work. The bit that I've had issues with is around the upstream ATF working on the SoCs Peter _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx/message/WUS2SCZGD3JOHLQNZOYH45KFOJBLJEL6/
